This mainboard contains an external RTC chip RX6110 SA. Enable usage of
this chip and set some initialization values to device tree.
Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This driver enables the usage of the external RTC chip RX6110 SA
(http://www5.epsondevice.com/en/products/i2c/rx6110sab.html) which is
connected to the I2C bus. The I2C address of this device is fixed. One
can change parameters in the device tree so that the used setup can be
adapted to match the configuration of the device on the mainboard.
Change-Id: I1290a10c2d5ad76a317c99c8b92a013309a605d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The thinkpad-acpi driver uses the UCMS (CMOS) ACPI method to control the
ThinkLight from the Operating System. This patch adds partial support for
that method, enough to enable or disable the ThinkLight:
echo on >/proc/acpi/ibm/light
echo off >/proc/acpi/ibm/light
With the original BIOS the UCMS method exposes a wide range of values
through a generic /proc/acpi/ibm/cmos interface. With the changes suggested
in this patch that interface is also exposed but only accepts the commands
to enable or disable the ThinkLight; all other commands are ignored.
This change would potentially benefit all currently supported Thinkpad
models, I only have an X201 available for tests though.
Change-Id: I80285f6630b5830766d82e3ecd174c4a51aa9066
Signed-off-by: Stefan Ott <stefan@ott.net>
Reviewed-on: https://review.coreboot.org/19644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
There are no GCC warnings anymore about set but unused variables, and
Clang warns about this switch, as it doesn’t know it.
So remove the switch to use the default set by the switch `Wall`.
Change-Id: Ie9eb26d4f8b298af231b952b547b71d68c649eaf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Only commented out code uses the variable `csr`, and GCC complains about
it, when enabling the warning *unused-but-set-variable*.
```
Checking for pciutils and zlib... me.c: In function ‘mei_dump’:
me.c:50:18: warning: variable ‘csr’ set but not used [-Wunused-but-set-variable]
struct mei_csr *csr;
^~~
```
As the code is commented, also comment out the declaration of the variable.
Change-Id: I4ecb2b5e9f32906ccfc8a0628d2e0f2d3ad39a02
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Currently only one board uses this northbridge in coreboot but some
patches are pending to add more.
Change-Id: If035e442d1a23674667f46a07b44c4f2b81be48c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
On Ubuntu 16.04 the libpci-dev package is required.
Change-Id: I942b3e96f5b8112166a105eb5a61f8f3cf16cb7c
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Reviewed-on: https://review.coreboot.org/19617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
- set GPIO_183 to high level for enabling the power of SD card
- delete all GPIOs for JTAG interface because they lead to problems with
Lauterbach debug hardware
Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The coreboot had no supported the different frequency for gru yet.
e.g:
we can't support the bob to run ddr 800M for rev3 board and
run 928M for rev4 board.
So, in order to support the 800M and 928M ddr frequency for bob different
boards. We will use the ram_id and board_id to select the board on bob.
Change-Id: I613050292a09ff56f4636d7af285075e32259ef4
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Spread Spectrum Modulator (SSMOD) is a fully-digital circuit used to
modulate the frequency of the Silicon Creations’ Fractional PLL in order
to reduce EMI.
We need to turn the DPLL spread spectrum feature on to
reduce the EMI noise for DDR on bob.
Change-Id: I75461d4235bcf55324e6664a1220754e770b4786
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Promote DRVR_CAP_8BIT from controller specific to controller independent
TEST=Build and run on Galileo Gen2
Change-Id: I51e4c990d3941a9f31915a5703095f92309760f1
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fix bug detected by coverity to handle the zero capacity case. Specific
changes:
* Reduce loop count by one to handle zero capacity case
* Use structure instead of dual arrays
* Move structures into display_capacity routine
Coverity Issues:
* 1374931
* 1374932
* 1374933
* 1374934
TEST=Build and run on Galileo Gen2
Change-Id: Ie5c96e78417b667438a00ee22c70894a00d13291
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
s230u seems only have two sata ports: one for the 2.5in hdd and one for
msata. map 0x11 (port 0 & 4) enables hdd but not msata, and map 0x5
(port 0 & 2) enables both.
Change-Id: I1e9e96f0d0849b1e8c4e02aa4f686ceb5e10b3ab
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Remove unused field in generic SD/MMC controller data structure.
TEST=Build and run on Galileo Gen2
Change-Id: I7169dca07509a6f2513d62b593742daf764010b2
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Is only present on the P45 subtype of chipset.
Change-Id: I6b138db6654c83c40b5ca4b65d6ccd51ad4277fa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested against a lenovo-manufactured tpm 1.2 module:
a /dev/tpm0 visible inside GNU/Linux, but there is no menu items in
SeaBIOS' interface, which seems a common issue of SeaBIOS on ivb boards.
Change-Id: Id0dee74d945bae5d77eb669d8b9d468a67aee508
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19521
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This replaces the custom environment controller handling in the it8728
driver with the common library.
It also updates the two existing boards with hwm register settings in
their devicetree config so they better match their vendor BIOS fan
control settings.
Change-Id: Idf0c8908ba5ad6ff552b8302bffc638aa9052941
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/19293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
BUG=None
TEST=emerge-sand coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I86a35551a9348ff6ad26dfccd3b2786282d56069
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/19479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to "Intel ® 4 Series Chipset Family datasheet" in the
description about GGC and DEVEN, CAPID0 bit46 is said to reflect the
presence of an internal graphic device. This would allow the P43 and
P45 chipset variants to work.
Change-Id: Icdaa2862f82000de6d51278098365c63b7719f7f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18515
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The NGI writes to legacy VGA registers which should not happen when
VGA cycles are assigned to a different device.
TESTED on ga-g41m-es2l
Change-Id: I0a03e35c0d7f2532edd6cc5e62d1cf07dab57f60
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This disables VGA cycles on IGD when an external VGA device is
found. This allows PCI or PCIe devices to be the 'main' VGA device if
found, while the IGD is still available.
TESTED on ga-g41m-es2l: SeaBIOS shows payload on external GPU while
linux (4.10) can use both as a framebuffer simultaneously without any
extra configuration.
Change-Id: I74890918feb0f1ff6b971c4aaa96f1f7b75266ac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Computes TSEG size dynamically.
Changes the size of legacy hole to match other Intel northbirdges.
Refactor this a little by needing one less variable.
Change-Id: I0e6898c06a2bc1016eeaa3f002ff6c39657018ae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Change a4b11e5c90 (soc/intel/skylake: Perform CPU MP Init
before FSP-S Init) dropped mtrr_check while re-organizing
code. Add the check back after MTRR setup is performed.
BUG=b:36656098
TEST=Verified that MTRR check is done after setup on poppy.
Change-Id: I440405c58c470ffa338be386d84870635530a031
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Configure the SD controller to handle the SD card slot.
* Galileo supports a removable SD card slot.
* Set SD card initialization frequency to 100 MHz.
* Set default removable delays.
* Build SD/MMC components by default
TEST=Build and run on Galileo Gen2
Change-Id: Iaf4faa40fe01eca98abffa2681f61fd8e059f0c4
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
With change a4b11e5c90 (soc/intel/skylake: Perform CPU MP Init
before FSP-S Init) to perform CPU MP init before FSP-S init, MTRR
programming was moved to be performed after CPU init is done. However,
in order to allow callbacks after MP init, PARALLEL_MP_AP_WORK needs
to be enabled. Since this option was not selected, MTRR programming
always failed in ramstage for Skylake / Kaby Lake mainboards.
BUG=b:36656098
TEST=Verified 2500+ cycles of suspend resume on poppy.
Change-Id: I22a8f6ac90ba35075ff97dd57bab66c129f3e771
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SD/MMC test support consists of:
* Add Kconfig value to enable the SD/MMC test support.
* Add Kconfig value to enable the logging support.
* Add SD/MMC controller init code and read block 0 from each partition.
* Add logging code to snapshot the transactions with the SD/MMC device.
* Add eMMC driver for ramstage to call test code.
* Add romstage code to call test code.
* Add bootblock code to call test code.
TEST=Build and run on Galileo Gen2
Change-Id: I72785f0dcd466c05c1385cef166731219b583551
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This code ought not to run if ME is disabled. It also prohibits
writing to some GMCH regs like GGC bit1.
Intel ® 4 Series Chipset Family datasheet refers to this as
"ME stolen Memory lock" without actually describing this
functionality.
Change-Id: Iaa8646e535e13c44c010ccd434a5af954cf7dfbc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Provide a failing get_wifi_sar_limits() to allow SAR Kconfig
options to be selected without relying on CHROMEOS which currently
has the only code to provide SAR data.
Change-Id: I1288871769014f4c4168da00952a1c563015de33
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19580
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use `uintptr_t` instead of `uint32_t`, fixing the error below on 64-bit
systems, where pointers are 64-bit wide.
```
cc -O0 -g -Wall -W -Wno-unused-parameter -Wno-unused-but-set-variable -Wno-sign-compare -Wno-unused-function -c -o intelmetool.o intelmetool.c
intelmetool.c: In function ‘dump_me_memory’:
intelmetool.c:85:45: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dump = map_physical_exact((off_t)me_clone, (void *)me_clone, 0x2000000);
^
```
BUG=https://ticket.coreboot.org/issues/111
Change-Id: Id8d778e97090668ad9308a82b44c6b2b599fd6c3
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/19567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Wise (Debian) <pabs@debian.org>
The device ids changed names between patches. Fix them to
not break the build any more.
Change-Id: I1d74d95ec6b516c4d8354a714b2b302557743fe0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19600
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
spi_crop_chunk is a property of the SPI controller since it depends
upon the maximum transfer size that is supported by the
controller. Also, it is possible to implement this within spi-generic
layer by obtaining following parameters from the controller:
1. max_xfer_size: Maximum transfer size supported by the controller
(Size of 0 indicates invalid size, and unlimited transfer size is
indicated by UINT32_MAX.)
2. deduct_cmd_len: Whether cmd_len needs to be deducted from the
max_xfer_size to determine max data size that can be
transferred. (This is used by the amd boards.)
Change-Id: I81c199413f879c664682088e93bfa3f91c6a46e5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19386
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: coreboot org <coreboot.org@gmail.com>
Now that we have a common block driver for fast spi flash controller,
provide spi_ctrlr structure that can be used by different platforms
for defining the bus-ctrlr mapping. Only cs 0 is considered valid.
Change-Id: I7228ae885018d1e23e6e80dd8ce227b0d99d84a6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19575
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
tis_close() must be called after tis_open() otherwise the locked
locality isn't released and the sessions hangs.
Tested=PC Engines APU2
Change-Id: I1a06f6a29015708e4bc1de6e6678827c28b84e98
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/19535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Nico Huber