Tested on lemp9, power limits are adjusted from the previously low
values to the values the thermal system can handle. This was
determined by increasing the values and running the system at 100%
CPU utilization until thermal throttling occured and the chassis
temperature became uncomfortable.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I5e176e9d98376f8e2dc415e4397efc456869e72d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43624
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The microphone is wired to the audio codec, not to the PCH. Disable the
DMIC interface.
Change-Id: I4128a694c1a66d3c2c2d1cb831fcca3487160f8f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45133
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This UART is already initialized by coreboot for the console, it does
not need to be initialized by the FSP.
Tested on lemp9.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I7c299fd7cf6fe53d1f500a899a14e63e51ad6266
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
To minimize the quirks the kernel has to apply, the headset mic is set
to its correct value in coreboot.
Tested on lemp9, audio is functional.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I6b59de95f01360a5f7779f87f39edeb75dedc215
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43631
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable SataPortsDevSlp for SATA ports 2 and 3.
Change-Id: Id6c69f4a6fe45cb5c6aad3f42c741a2724c6166c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Enable the I2C HID driver, configure I2C bus 0 and add the touchpad
device to the devicetree.
Tested on lemp9, touchpad confirmed to use i2c-hid driver in Linux
instead of PS/2.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ic3a90fda134b1d53f28ab687b3033ec52fee843b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43623
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
_GPE cannot be anywhere but at the root of the ACPI namespace.
This change ensures that is always the case.
Tested on lemp9, GPE still in correct location.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib31683b06e61da4b1859cd939c36879cebf4c03c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43630
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs required for DeepSx (e.g. SLP_SUS#) are not hooked up on the
lemp9. Therefore, drop the DeepSx settings.
Tested on lemp9, suspend works correctly.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Iab179abd7adc3a65dcfc43ce1b5742d514b711fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43629
Reviewed-by: Michael Niewöhner
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested on lemp9, SA thermal device appears in lspci.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I527e586b1dae5f8087d2364c63c9db5bcb643214
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Don't configure USB3 port 4 since it's not used.
Change-Id: I6919f5ec3a5be53373f2ab75063764287b53baf5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner
Currently HECI3 gets enabled by the option Heci3Enabled, but this
duplicates the devicetree on/off options. Therefore depend on the
devicetree for enablement of the HECI3 controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Heci3Enabled setting, and divergent
devicetrees were adjusted.
Change-Id: Ic7d52096aee225c2ced1e1bc29ca850fe5073edc
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44579
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
MODEM_CLKREQ / CNVI_CLKREQ has no external pull-down resistor.
When there is no M.2 card populated, the pin is floating. Thus
enable an internal 20K PD.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I37e0a9d7e9e0a8c8a7ac198abfd3995b8b0f9e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Add CNVi and PCIe wifi devices to the devicetree and enable the wifi
driver and SMBIOS tables in Kconfig.
Test: both CNVi and PCIe wifi devices work fine
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I16e04dbbf5fc3a163ce5a2bb8de646877d5cbc0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43654
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rework the comments:
- fix wrong gpio / net names
- convert all comments to <gpio> / <net name>
- add more information where appropriate
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I51b552fd3255d5627dcc012e677bad51be517cf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43650
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
INTP_OUT can be used as Type-C VBUS sense input/interrupt but is
currently unused in coreboot. It isn't a requirement for PD to work.
Disable it for now.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I233fbb562969487dff095ba6589fb9da3301ae4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43647
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable internal pull-ups for SATAXPCIE pads since there are external
ones at the M.2 slot's PEDET pins.
Test: both, SATA and NVME devices work fine on both slots
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6be716620695ac38c44a17abe1c4de97b099b8d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43645
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are pads being unused for various reasons:
a) missing board support (DeepSx: SUSWARN#)
b) unneeded feature ID pins
- currently no known device models without keyboard backlight
- currently no known device models without TPM
c) BOARD_ID (L140CU/L140ZU) is fixed and known at build time
d) DDR_TYPE_*: there is only one known ram model
e) strap-only pads
f) unconnected pads
Configure them as NC with appropriate pull-up if no external pull exists.
The latter was checked by schematics and looking at the board.
When any of the unused ID pins is needed in the future, they can be
reactivated easily (configure as GPI).
Further, convert from use of legacy macro PAD_CFG_NC to PAD_NC.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia370c180d5ae6f48360be14af3cbab29e6814e75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43644
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
L140CU has a TPM2 connected via SPI. Add the TPM device to the
devicetree and enable it.
According to Intel doc#615170-001, PIRQ is required for SPI TPM to work.
Since the TPM is connected to GPP_A7, enable NF1 (PIRQA#) and set it as
TPM interrupt in Kconfig.
Note: The PCH maps either LPC TPM or SPI TPM to the same address and
handles either LPC or SPI communication transparently. Thus we can use
MAINBOARD_HAS_LPC_TPM here, which implements TPM via that address.
Tested, but only polling works currently, because there is some upstream
issue with the tpm_tis module in current Linux kernels. [1]
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1770021
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I26d3b396fe1e99368e18fd3a6a9f02e3585b9f6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43641
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Built with BUILD_TIMELESS=1, resulting coreboot.rom does not change.
Change-Id: I655bc7576e8ff48258a2a19387e01372f4bbea3d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
This adds ACPI code for System76 EC and converts system76/lemp9
to use EC_SYSTEM76_EC.
Tested on system76/lemp9.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I1f693268d94b693b6764e4a3baf4c3180689f3be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Michael Niewöhner
Update processor power limit configuration parameters based on
common code base support for Intel Cannonlake SoC based platforms.
BRANCH=None
BUG=None
TEST=Built and tested on drallion system
Change-Id: Iac6e6f81343fcd769619e9d7ac339430966834f6
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some existing devicetrees were manually adapted to anticipate
root-port switching. Now, their PCI-device on/off settings should
just reflect the `PcieRpEnable` state and configuration happens
on the PCI function that was assigned at reset.
Change-Id: I4d76f38c222b74053c6a2f80b492d4660ab4db6d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
The `USE_BLOBS` config only exists for idealistic reasons. If we would
allow us to use blobs by default, we wouldn't need that option and could
just always do it. It's generally debatable for the project as a whole,
but not per board/subject.
Change-Id: I8591862699aef02e5a4ede32655fc82c44c97555
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We can make our lifes much easier by removing its dependency on
`ADD_FSP_BINARIES`. Instead, we imply the latter if the repository
is to be used. We can also hide a lot of unnecessary prompts in
this case.
Also, remove default overrides and selects for the two that are
now unnecessary.
Change-Id: I8538f2e966adc9da0fbea2250c954d86e42dfeb3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39882
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I2aa745e03e62ff8b9b5c9cb6f91d7f832f599f8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Only some mainboard vendors have a prompt for this option. Let's be fair
and give this ability to everyone.
Change-Id: I03eec7c13d18b42e3c56fb1a43dc665d5dbd1145
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- Channel 0: 8-GB on-board DDR4 Samsung K4AAG165WA-BCTD
- Channel 1: 8-GB/16-GB/32-GB DDR4 SO-DIMM
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
