Toggle LEDs after successful dock and undock.
On boot the LED will light up and on undock button
press the LED will turn off again.
Tested on Lenovo T500.
Change-Id: Ib5851f4abcedf4041faae6b3b810102012f488cd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The flag FF_FreezeDis marks if this feature is disabled. For a better
readability rename freeze_mode to freeze_disable and invert the meaning
of this information.
Change-Id: I648b2392d2c8046965479511fde485a9cb934378
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The two flags FF_FanReq and FF_Freeze_Dis should be treated as
8 bit values and not as 32 bit. Change the length of these fields to
1 byte and adjust the offset and mask for FF_FanReq.
Change-Id: If5e9e8b16491a33997cc39c3dd9b80f97682adc6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch basically does two things -
1) Remove unnecessary setting of flex_ratio to TDP nominal:
Factory configured (default) Max Non-TURBO ratio(P1) is already cofigured
in MSR_PLATFORM_INFO(0xCE).
If this Maximum Non-TURBO Ratio(P1) needs to be modified, it should be done
using MSR_FLEX_RATIO (0x194).
Here, in this code, the FLEX_RATIO is being modified by the TDP Nominal
Ratio, reading the MSR_CONFIG_TDP_NOMINAL(0x648). But this value is
actually less than the factory configured Maximum Non TURBO Ratio (P1).
So, this code is actually not required.
Also, the Bit 12 in PCH Soft Strap Register is already set in descriptor.
This Bit implies Processor Boot Max Frequency -
0 = Disable Boot Max Frequency
1 = Enable Boot Max Frequency (Default)
This setting determines if the processor will operate at maximum frequency
at power-on and boot.
Thus this patch will avoid one extra platform warm reset now onwards.
2) Remove wrongly setting Max Frequency in Bootblock phase:
In the function set_max_frequency(), the P-State max ratio was set to
TDP Nominal ratio if C-TDP was enabled, else it was set to Max Non
Trbo ratio.
But, when the cpu gets reset, it will operate with the Max-Non Turbo
ratio only, which is greater than the TDP Nominal ratio.
So, no need to set back the ratio to TDP Nominal which is lower than
the currently operating frequency.
BUG=none
BRANCH=none
TEST=Build and boot poppy
Change-Id: I24bfc86ddf0f038d85da938e41e950382fe2a6c3
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the new PAD_CFG_GPI_INT macro to specify the headset codec
interrupt as specifically edge triggered (since it is registered
as EDGE_BOTH in the devicetree) in order to prevent the interrupt
from firing unexpectedly when the system is resuming.
Also change the DSP interrupt to edge triggered since the kernel
is registering with IRQF_TRIGGER_RISING in order to prevent an
interrupt storm when it asserts.
BUG=b:35582164
TEST=manual testing on Eve:
1) ensure the headset codec sends interrupt on insert and remove
2) ensure there is only one interrupt counted when DSP asserts irq
Change-Id: I40a8ee667de653e4e70770cd96b6417442c1b0ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make this pin a GPI as it is supposed to be an input from the touch
controller and not driven by the AP.
BUG=b:35581264
TEST=check pin state with a scope
Change-Id: Ife5f84fcc614255b20e44389279d515a12f5751d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Board changes in rev6+ have a fix to VDDQ that should fix the issue
that was being seen with this SKU, so only lower the memory speed on
older boards.
BUG=b:37172778
TEST=memory stress testing on rev6 boards
Change-Id: I6d6fe730cabd74af23eab3f02feef9da01a35fd4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for waking from and logging device events that
originate in the Embedded Controller. As this device uses
Deep S3 it relies on the EC to wake the AP from the trackpad
and DSP wake sources.
BUG=b:30624430
TEST=manual testing on Eve: wake from Deep S3 via trackpad and
DSP and verify the event log contains the expected device event.
Change-Id: I0d6a9c5bfd4cea85e13446ffaa6fe3dab0db96a2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for the new EC device event interface which is used to
report events from devices that are connected behind the EC.
This can be used to differentiate wake sources from the EC in the case
that the EC has the wake pins from various devices.
This can be used in case the AP is unable to directly wake from the
device itself, for example when using the Deep S3 state on Intel
platforms only a few pins can directly wake the AP.
BUG=b:30624430
TEST=build google/* boards that use chrome EC. Feature is used and
tested further in a subsequent commit.
Change-Id: I5126c6d6ffb6b0ef6e8db8dcd5aec62db925a371
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Replace the unused "thermal overload" event with the new
"device event" and define the first few device events that are
supported by the Chromium EC.
BUG=b:30624430
TEST=build for google/* mainboards
Change-Id: I1f3aeedb87c2aad29a0a67b5c50c29a6961fb45f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update this header from the upstream source so new host
commands can be used in coreboot.
https://chromium.googlesource.com/chromiumos/platform/ec
commit bbb759ceaa843f548f90c35d1668e17c8879bad3
BUG=b:30624430
TEST=build google/* and intel* boards
Change-Id: I56c9f891262d8984b6a9a69d96752c2dd6bb2371
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Chrome EC event for "thermal overload" was never implemented and
is being repurposed as the EC event mask is out of free bits.
Remove this from the boards that were enabling it.
BUG=b:36024430
TEST=build coreboot for affected boards
Change-Id: I6038389ad73cef8a57aec5041bbb9dea98ed2b6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
- Clean utilities directories on clean & distclean
- Have the distclean target clean up after 'what-jenkins-does'
Change-Id: I7d25d8234528b19bf36df6845a4500dbe1cbf9a4
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The architecture is determined by __riscv__ in the LZ4_copy8 function
(located in src / commonlib / lz4_wrapper.c). __riscv exists in gcc7.1.1.
But __riscv__ does not exist.
Change-Id: I38fd41da9afd76c254f0c3d6984579c3790e5792
Signed-off-by: XiangWang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/20125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Waterman <aswaterman@gmail.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
DISPPLANE_BGRX888 defined in drivers/intel/gma/i915_reg.h
included in i915.h file
Change-Id: I4e9414f39a29e4eac7e325672ce6520a5654d3bc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Set RX6110SA RTC backup mode to primary cell. This mode reduces the
backup current consumption of the RTC.
Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The used RTC6110SA has issues to enter backup mode when the power supply
decreases too slow when the mainboard is turned off. Switch to backup
mode "primary cell" to make sure backup mode will be entered correctly
on power-off. In addition set IOCUTEN to minimize the backup current
consumption of the RTC.
Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
According to the datasheet the RTC needs a power rising slope of no more
than 100µs/V to ensure a correct power-on reset. If the mainboard that
hosts the RTC cannot guarantee this, a software reset sequence is needed
in the case where the battery was drained completely.
As the rising slope of the power supply depends on so many parameters
and is highly mainboard specific, refactor the initialization code to
perform a software reset every time a power loss event is recognized by
the RTC.
Change-Id: If64d672e51667523058041bd00e1e50ac047143d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There is no choice, if not leaving it with the default the build
will fail.
Change-Id: Id91e3ce87f8ced3001fcd2125f8f6781b270f5bc
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cannonlake has built-in UART driver as part of LPSS block. However port
mapped decoders are in use as well.
Change-Id: I9f209bf29c1748c5beea31bc6b31cb07a1e14195
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/20063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When the C compiler expects 16-byte alignment of the stack it is
at the call instruction. Correct existing call points from assembly
to ensure the stacks are aligned to 16 bytes at the call instruction.
Change-Id: Icadd7a1f9284e92aecd99c30cb2acb307823682c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the TSC for the Stoney Ridge monotonic timer. Modern AMD
CPUs have invariant timestamp counters. This patch brings the
feature more in line with other devices and allows the use of
typical monotonic timer functions.
BUG=chrome-os-partner:62578062
Change-Id: I07b05fbc7cdea54a45daac01954284a9fd67e42f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
- Update checkpatch.pl to version 522b837
(checkpatch: warn when formats use %Z and suggest %z)
- This update moves the const_struct definitions into an external file.
coreboot will want to update this file, but for now I'm just pulling it
in directly from the linux tree.
- Update spelling.txt used by checkpatch.pl to version 505d308
(scripts/spelling.txt: add "overide" pattern and fix typo instances)
- Add better notes where things have been changed for coreboot to make
future merges easier.
Change-Id: I0ef067874fe7b1d23276a10e63858895d6083f69
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There are up to two on-board PCI devices where bus master has to be
enabled in PCI config space. As there is no need for a complete PCI
driver for these devices just set the bus master bit in
mainboard_final().
In a perfect world that would be the task of the runtime driver which
unfortunately don't do that.
Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The ALSB gnvs variable is used to load the OpRegion memory
address into the ASLS register on the S3 resume path, and must
therefore first be set on the normal boot path.
This patch brings Haswell in line with SNB/IVB/Nehalem, which
already save the OpRegion address in ASLB.
Change-Id: Ie062cbfe7e7f60c2a4e2b9111f6b6da87ced7a39
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Now that pci_devs.h is part of soc/ and not used for multiple
southbridges:
* Remove devices not present in the Stoney Ridge APU
* Complete the list to include additional devices besides
those in the FCH.
BUG=chrome-os-partner:62578372
Change-Id: I1cd2d5e41473f362bbfd28ee93788a292bc33991
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20370
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a memmap file with a cbmem_top() function. Remove the
LATE_CBMEM_INIT, allowing the default of EARLY. Remove calls
to the late-only set_top_of_ram() function.
Change-Id: I11ad7190031c912642a7312f2fc6f792866288b7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Change-Id: Ic2cdfa08cdae9f698eb2f8fa4c4ae061f1a7d903
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I66cde1adcf373889b03f144793c0b4f46d21ca31
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I82bf68a7ee54ff88f65aacc9eb0dbc30d013aae0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: Ie685bbbb1cbf06d32631ea40ad120b6f45374b2e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I9f4155285529ec28e826637a61436478f648704c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Describe RT5663 headphone codec in ACPI so it can
be enumerated by the OS.
- Supply NHLT binaries for RT5663
BUG=b:62872377
TEST=Apply full patch set and UCM, verify basic audio works.
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Change-Id: I5bbd58b0e660cdf5089e6a6dd35a757ecf8ec076
Reviewed-on: https://review.coreboot.org/20305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Problem was introduced by fb2f667da2 "nb/amd/amdk8: Link raminit_f.c"
which linked debug.c and was not tested with this option.
Change-Id: I8597a6915c65ea783a864110cb23ecb34ea0611b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the code we do the following in a number of places
to pre-initialize an array with a certain value before
overwriting some of the array with other values:
u8 mainboard_picr_data[FCH_INT_TABLE_SIZE] = {
[0 ... FCH_INT_TABLE_SIZE-1] = 0x1F,
}
clang does not like that behavior unless we specify
the option -Wno-initializer-overrides.
Remove the check for gcc in those places, too, because
1) it would silently change array contents between compilers
2) the check isn't sufficient to determine compilation on
clang vs gcc
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I93cc121b6fec099fcdbd5fd1114c2ff7cbc291dc
Reviewed-on: https://review.coreboot.org/20384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Patrick Rudolph