Enable the cr50 TPM and interrupt as GPE0_DW1_28 for use during
verstage. The interrupt is left in APIC mode as the GPE is
still latched when the GPIO is pulled low.
BUG=chrome-os-partner:53336
Change-Id: I28ade5ee3bf08fa17d8cabf16287319480f03921
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Support reading the ACPI GPE status (on x86) to determine when
the cr50 is ready to return response data or is done processing
written data. If the interrupt is not defined by Kconfig then
it will continue to use the safe delay.
This was tested with reef hardware and a modified cr50 image
that generates interrupts at the intended points.
BUG=chrome-os-partner:53336
Change-Id: I9f78f520fd089cb4471d8826a8cfecff67398bf8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Implement the generic acpi_get_gpe() function to read and clear
the GPE status for a specific GPE.
Tested by watching GPE status in a loop while generating interrupts
manually from the EC console.
BUG=chrome-os-partner:53336
Change-Id: Id885e98d48c2133a868da19eca3360e2dfb82e84
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Initialize the GPEs from mainboard config in bootblock, so they
can be used in verstage to query latched interrupt status.
I still left it called in ramstage just to be sure that the
configuration was not overwritten in FSP stages.
Tested by reading and reporting GPE status in a loop in verstage
and manually triggering an interrupt on EC console.
BUG=chrome-os-partner:53336
Change-Id: I1af3e9ac1e5c59b9ebb5c6dd1599309c1f036581
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Add a function that can be implemented by the SOC to read
and clear the status of a single GPE. This can be used
during firmware to poll for interrupt status.
BUG=chrome-os-partner:53336
Change-Id: I536c2176320fefa4c186dabcdddb55880c47fbad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Unify the function names to be consistent throughout the driver
and improve the handling while waiting for data available and
data expected flags from the TPM.
BUG=chrome-os-partner:53336
Change-Id: I7e3912fb8d8c6ad17d1af2d2a7189bf7c0c52c8e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Clean up the mask and timeout handling in the locality functions
that were copied from the original driver.
BUG=chrome-os-partner:53336
Change-Id: Ifa1445224b475aec38c2ac56e15cb7ba7fcd21ea
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Rename the low-level functions from iic_tpm_read/write to
cr50_i2c_read/write to better match the driver name, and pass in the
tpm_chip structure to the low-level read/write functions as it will
be needed in future changes.
BUG=chrome-os-partner:53336
Change-Id: Ib4a68ce1b3a83ea7c4bcefb9c6f002f6dd4aac1f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Use two different timeouts in the driver. The 2ms timeout is needed
to be safe for cr50 to cover the extended timeout that is seen with
some commands. The other at 2 seconds which is a TPM spec timeout.
BUG=chrome-os-partner:53336
Change-Id: I77fdd7ea646b8b2fef449f07e3a08bcce174fe8b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reduce the static buffer size from the generic default 1260
down to 64 to match the max FIFO size for the cr50 hardware
and reduce the footprint of the driver.
BUG=chrome-os-partner:53336
Change-Id: Ia88facca607f3fd5072d0d986323fde075f15855
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Originally I thought it would be cleaner to keep this code in one
place, but as things continue to diverge it ends up being easier
to split this into its own driver. This way the different drivers
in coreboot, depthcharge, and the kernel, can all be standalone
and if one is changed it is easier to modify the others.
This change splits out the cr50 driver and brings along the basic
elements from the existing driver with no real change in
functionality. The following commits will modify the code to make
it consistent so it can all be shared with depthcharge and the
linux kernel drivers.
BUG=chrome-os-partner:53336
Change-Id: Ia9a65e72519b95f5739e3b7a16b9c2431d64ebe2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Move the common enums and variables to tpm.h so it can be
used by multiple drivers.
BUG=chrome-os-partner:53336
Change-Id: I0febe98620d0ddd4ec6b46cd3073e48c12926266
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
This patch sets some magic number in magic undocumented registers that
are rumored to make USB 2.0 signal integrity better on Kevin. I don't
see any difference (unfortunately it doesn't solve the problems with
long cables on my board), but I guess it doesn't hurt either way.
BRANCH=None
BUG=chrome-os-partner:56108,chrome-os-partner:54788
TEST=Booted Kevin with USB connected through Servo. Seems to have
roughly the same failure rate as before.
Change-Id: If31fb49f1ed7218b50f24e251e54c9400db72720
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c5c8f0f80ea1ebb042bcb91506a6100833e7e84
Original-Change-Id: Ifbd47bf6adb63a2ca5371c0b05c5ec27a0fe3195
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/370900
Original-Reviewed-by: Guenter Roeck <groeck@chromium.org>
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-on: https://review.coreboot.org/16265
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add FSP 2.0 support in ramstage.
Populate required Fsp Silicon Init params and configure mainboard
specific GPIOs.
Define function fsp_soc_get_igd_bar needed by fsp2.0 driver for
pre OS screens.
Change-Id: Ib38ca7547b5d5ec2b268698b8886d5caa28d6497
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16592
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Remove fsp1.1 driver code that adds vbt.bin & use soc/intel/common
instead to add vbt.bin in cbfs.
Also, VBT blob is added to CBFS as RAW type hence when walking the
CBFS to find vbt.bin, search with type as RAW.
Change-Id: I08f2556a34f83a0ea2b67b003e51dcace994361b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16610
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This implements PRW method for WLAN and configures PCIe wake pin to
generate SCI.
BUG=chrome-os-partner:56483
TEST=Suspend the system into S3 or S0ix. System should resume through wake
event from wifi.
Change-Id: I9bd078c2de19ebcc652b5d981997d2a5b5f0b1b7
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/16611
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In spd_util.c function mainboard_get_spd_data(), spd_file can
either be NULL or will point to the first byte of the SPD data,
and should not be dereferenced.
Change-Id: I08677976792682cc744ec509dd183eadf5e570a5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16612
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The correct id string for gm45 is "$VBT CANTIGA ".
This can be found in the gm45 option rom:
"strings vbios.bin | grep VBT".
Change-Id: Icd67a87dac774b4b3c211511c784c4fb4e2ea97c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16551
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This implements "Keep VESA framebuffer" behavior on VGA output of gm45.
This patch reuses Linux code to compute vga divisors.
Change-Id: I2db5dd9bb1a7e309ca763b1559b89f7f5c8e6d3d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16338
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The intel x4x and gm45 have very similar integrated graphic devices.
Currently the x4x native graphic init enables VGA, while gm45 can output
on LVDS.
This patch reuses the x4x graphic initialisation code
to enable output on VGA in gm45 in a way that the behavior is similar to vbios:
If no VGA display is connected the internal LVDS screen is used.
If an external screen is detected on the VGA port it will be used instead.
Change-Id: I7e9ff793a5384ad8b4220fb1c0d9b28e6cee8391
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16295
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Implement postcar stage cbmem console support. The postcar stage
is more like ramstage in that RAM is already up. Therefore, in
order to make the cbmem console reinit flow work one needs the cbmem
init hook infrastructure in place and the cbmem recovery called.
This call is added to x86/postcar.c to achieve that. Additionally,
one needs to provide postcar stage cbmem init hook callbacks for
the cbmem console library to use. A few other places need to
become postcar stage aware so that the code paths are taken.
Lastly, since postcar is backed by ram indicate that to the
cbmem backing store.
BUG=chrome-os-partner:57513
Change-Id: I51db65d8502c456b08f291fd1b59f6ea72059dfd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16619
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The console_init(), MTRR printing, and loading ramstage
logic was previously all in assembly. Move that logic
into C code so that future features can more easily be
added into the postcar boot flow.
BUG=chrome-os-partner:57513
Change-Id: I332140f569caf0803570fd635d894295de8c0018
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16618
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The declarations for console_init() were unconditionally
exposed even though there is a Kconfig option. Correct this
by honoring the CONFIG_POSTCAR_CONSOLE condition.
BUG=chrome-os-partner:57513
Change-Id: Id45ae3d7c05a9f4ebcf85c446fc68a709513bb0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16617
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Elyes HAOUAS