Disable PSE loading by default. If left enabled (current default),
the EHL coreboot will end up in endless restart loop, due to FSP
unable to locate PSE FW image and trigger global reset.
However disabling this flag (PchPseEnable) will cause the coreboot
to trigger a single reset due to CSE signal (HECI: CSE does not
meet required prerequisites). The reason behind this is that FSP
need to perform static disabling (power gate) to fully shut down
PSE HW, and to do this will need to global reset entire system
including CSE. Then PMC will power gate PSE from the start.
To avoid this behavior, the best way to disable PSE is to disable
via IFWI FIT softstrap (For specific detail can refer to Intel EHL
coreboot MR2 release notes). With this, PMC will power gate PSE
from the first cold boot and system will boot happily without
single reset behavior.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Iccc0ab1c2e4ebb53013795933eb88262f70f456f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
When the cpu_cl_discovery is called, coreboot actually assigns a BAR
to cpu crashlog pci device. Hence, we don't need to assign a tmp BAR
for cpu crashlog pci device
BUG=b:195327879
TEST=Found BERT table is created and the tcss function is ok in depthcharge
Change-Id: Ib7e6772be51ec4f26ef31fed6cb2bddef8ffc6be
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add option to initialize the TPM in PSP verstage during s0i3 resume.
This is needed if the TPM is reset in s0i3. FSDL is handling
restoring everything else, so only the minimum TPM initialization is done.
Move aoac and i2c init before psp_verstrage_s0i3_resume becasue i2c
needs to be ready before attempting to restore tpm.
BUG=b:200578885,b:197965075
TEST=Multiple cycles of S0i3 suspend resume. ~66ms of additional delay.
BRANCH=None
Change-Id: Ie511928da6a8b4be62621fd2c4c31a8d1e724d48
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Some weird things happen inside FSP and the routing is not correctly
applied, with PIN D being used but lacking a proper routing in ACPI.
To work around this issue generate _PRT for all 4 INT pins.
Change-Id: I5be6e4514f8c6a47bb887d9f9b95181c9f426a51
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add .enable method that will set the CSME state. The state is based on
the new CMOS option me_state, with values of 0 and 1. The method is very
stable when switching between different firmware platforms.
This method should not be used in combination with USE_ME_CLEANER.
State 1 will result in:
ME: Current Working State : 4
ME: Current Operation State : 1
ME: Current Operation Mode : 3
ME: Error Code : 2
State 0 will result in:
ME: Current Working State : 5
ME: Current Operation State : 1
ME: Current Operation Mode : 0
ME: Error Code : 0
Tested on:
KBL-R: i7-8550u
CML: i3-10110u, i7-10710u
TGL: i3-1110G4, i7-1165G7
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I374db3b7c0ded71cdc18f27970252fec7220cc20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Thermal configuration registers are now located behind PMC PWRMBASE
for Alder Lake Point PCH. Hence, ADL SoC to select
SOC_INTEL_COMMON_BLOCK_THERMAL_BEHIND_PMC to let thermal low threshold
is being set as per mainboard provided `pch_thermal_trip`.
Note: These thermal configuration registers are RW/O hence, setting
those early prior to FSP-S helps coreboot to set the desired low
thermal threshold for the platform.
BUG=b:193774296
TEST=Dump thermal configuration registers PWRMBASE+0x150c etc. prior
to FSP-S shows that registers are now programmed based on
'pch_thermal_trip' and lock register BIT31 is set.
Change-Id: I0f972f47845c123f4f74fd75091c9703d54db796
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59271
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Thermal configuration has evolved over PCH generations where
latest PCH has provided an option to allow thermal configuration
using PMC PWRMBASE registers.
This patch adds an option for impacted SoC to select the Kconfig
for allowing thermal configuration using PMC PCH MMIO space.
BUG=b:193774296
TEST=Able to build and boot hatch and adlrvp platform.
Change-Id: I0c6ae72610da39fc18ff252c440d006e83c570a0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59209
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch uses `clrsetbits32` helper function to set thermal
device Low Temp Threshold (LTT) value.
BUG=b:193774296
TEST=Able to build and boot hatch and adlrvp with this change.
Change-Id: I51fea7bd2146ea29ef476218c006f7350b32c006
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59310
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures IA common thermal block is now able to compile
under romstage with necessary compilation issues fixed.
BUG=b:193774296
Change-Id: I3279f55436977ab9a47e04455d8469e50b5c33c8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59391
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`struct device *dev` as part of the pch_get_ltt_value() argument is
being used hence, replace with `void`.
BUG=b:193774296
Change-Id: Iecdf6f6c3023f896a27e212d7c59b2030a3fd116
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59390
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the VccIn Aux Imon IccMax for ADL-M
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I21753f2e5e9867f22c05e087cbf1f1e097d28bca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add separate gpio table for TPM i2c and interrupt. Remove TPM gpios from
early_gpio_table. This allows for initializing TPM gpios separately from
other gpios.
BUG=b:200578885
BRANCH=None
TEST=Build and boot guybrush
Change-Id: I51d087087b166ec3bb3762bc1150b34db5b22f2f
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59083
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Related to https://review.coreboot.org/c/coreboot/+/58555
commit-id: 35b7e0a2d82ac
In 58555, we added the SOC ID for Stoneyridge in amdfwtool
command line. But it raised building error because it then called
"set_efs_table" without setting SPI mode. So we skipped calling that.
But in set_efs_table, it has case for Stoneyridge. The boards also
need to have this setting. So we remove the skipping and give the
proper SPI mode in mainboard Kconfig.
Change-Id: I24499ff6daf7878b12b6044496f53379116c598f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This reverts commit 1399442289.
Reason for revert:
Some Cr50 chips with old firmware version (x.y.22) don't support
long pulse interrupt command, requiring dynamic GPIO PM to be disabled
to intercept short pulse interrupt.
Due to this coreboot needs to expose SGPM, RGPM and EGPM ACPI methods
to support power gating of GPIO communities from the kernel when dynamic
GPIO PM is disabled.
BUG=b:204832081
BRANCH=None
Test= S0ix works with dynamic PM disabled.
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Change-Id: I2b5b00878062f8a499641d7a47db54ed078cd6cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Make psp verstage initialization more granular be splitting
verstage_soc_init into separate functions. Specifically, create
soc init functions for espi, i2c spi, and aoac.
BUG=b:200578885
BRANCH=None
TEST=Build and boot guybrush
Change-Id: I489889a0dfd4016aa4f2b53a2c6a7a1ea4459e60
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This patch adds support for loading SPM firmware from CBFS to SPM SRAM.
SPM needs its own firmware to enable SPM suspend/resume function which
turns off several resources such as DRAM/mainpll/26M clk when linux
system suspend.
TEST=program counter of SPM is correct value(0x250) after booting up
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ia13e5a2ecf09561856b7e958128cd2f045c39f33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59341
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SSPM is "Secure System Power Manager" that provides power control in
secure domain. The initialization flow is to load SSPM firmware to
its SRAM space and then enable.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I92eb501a1e48dd02d2f94ff392933261e6a42391
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Setting of MSDC is defined by soc, so we move them to soc folder.
TEST=emerge-cherry coreboot; emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I84ad8a4cde120c97024870ebf750d44b36c2284d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
DCM (dynamic clock management) can dynamically slow down or gate clocks
during CPU or bus idle. Enable DCM settings on the MT8186 platform.
TEST=build pass and check register ok
BUG=b:202871018
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Change-Id: I82add5ae629d59f7d6773e26ac9cba9d54ab8caf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
This patch modifies the pch_get_ltt_value() function return type from
uint16_t to uint32_t to accommodate platforms with more than one thermal
threshold.
For example: Alder Lake PCH Trip Point = T2L | T1L | T0L
where T2L > T1L > T0L.
BUG=b:193774296
Change-Id: I5f46ccb457b9cfebf13a512eabb3fb0fab8adb39
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Now that CBFS has this functionality built in, we no longer need to
manually code it.
payload_preload used to use the payload_preload_cache region to store
the raw payload contents. This region was placed outside the firmware
reserved region, so it was available for use by the OS. This was
possible because the payload isn't loaded again on S3 resume.
cbfs_preload only uses the cbfs_cache region. This region must be
reserved because it gets used on the S3 resume path. Unfortunately this
means that cbfs_cache must be increased to hold the payload. Cezanne is
the only platform currently using payload_preload, and the size of
cbfs_cache has already been adjusted.
In the future we could look into adding an option to cbfs_preload that
would allow it to use a different memory pool for the cache allocation.
BUG=b:179699789
TEST=Boot guybrush and verify preloading the payload was successful
CBFS DEBUG: get_preload_rdev(name='fallback/payload') preload successful
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idc521b238620ff52b8ba481cd3c10e5c4f1394bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
eGPIO is a scheme which allows special power island domain IOs to be
reused as regular chip GPIOs by muxing regular TLMM functions with
Island Domain functions. Allow the eGPIO to be configured via
gpio_configure API to be used as a TLMM gpio.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Change-Id: Ib2598a41ba3bb8a8a2acff8253b5bb78633f89f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
TEST=boot kernel from eMMC ok
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I3bc06b1fc506b1d6f54f7f456117d22477a87e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The Corsola reference design has both eMMC and SD Card interfaces
so we have to configure both in RAM stage.
TEST=build pass
BUG=b:202871018
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f26a8a11edd29a80a7195e3a324151d66ecb293
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The _Static_assert without message string is only available
since C++17. Add the message to avoid build fail in the macro.
BUG=b:203145462
BRANCH=cherry
TEST=build pass and boot pass
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: Ib146ffafc21b9dbb9d383c9343a9ec1d7c478faf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59298
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CPUCP is CPUSS Control Processor. It refers to the firmware for control
CPUSS active power management.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: Idac22c8cb231658616999bc577bdf49f9aa7ae74
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
There are currently two users of the SPI hardware, the LPC SPI DMA
controller, and the boot_device_rw device. We need to ensure exclusivity
to the SPI hardware otherwise the SPI DMA controller can be interrupted
and it will silently skip transferring some blocks.
Depending on the SPI speed, this change might add a small delay when
clearing the elog since a DMA transaction might be in flight. I'll
continue optimizing the boot flow to avoid the delay.
BUG=b:179699789
TEST=Hack up the code to interleave SPI transactions and verify this
patch fixes the silent data corruption.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5eee812a6979c8c0fb313dd2fbccc14b73d7d741
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This reverts commit adb393bdd6.
This relands commit 6260bf712a.
Reason for revert:
The original CL did not handle some devices correctly.
With the fixes:
* commit 36721a4 (mb/google/brya: Add GPIO_IN_RW to all variants'
early GPIO tables)
* commit 3bfe46c (mb/google/guybrush: Add GPIO EC in RW to early
GPIO tables)
* commit 3a30cf9 (mb/google/guybrush: Build chromeos.c in verstage
This CL also fix the following platforms:
* Change to always trusted: cyan.
* Add to early GPIO table: dedede, eve, fizz, glados, hatch, octopus,
poppy, reef, volteer.
* Add to both Makefile and early GPIO table: zork.
For mb/intel:
* adlrvp: Add support for get_ec_is_trusted().
* glkrvp: Add support for get_ec_is_trusted() with always trusted.
* kblrvp: Add support for get_ec_is_trusted() with always trusted.
* kunimitsu: Add support for get_ec_is_trusted() and initialize it as
early GPIO.
* shadowmountain: Add support for get_ec_is_trusted() and initialize
it as early GPIO.
* tglrvp: Add support for get_ec_is_trusted() with always trusted.
For qemu-q35: Add support for get_ec_is_trusted() with always trusted.
We could attempt another land.
Change-Id: I66b8b99d6e6bf259b18573f9f6010f9254357bf9
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
VT-d needs to disabled for early silicons as it results in a
CPU hard hang.
BUG=b:197177091
Test=Boot brya to OS with no hang
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b9b76b6527d8b80777cb7588ce6b12282af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
For the stoneyridge, soc_name is not set in Makefile, so set_efs_table
is not called. Keep it unchanged.
Change-Id: I0e82188ce64733420a578446e22a077ef789be92
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
None of the *_DEVID defines was used in the code, so drop those. The SoC
code uses the PCI ID defines from include/device/pci_ids.h instead.
Since it might still be useful to have the PCI device IDs as a reference
in the SoC's pci_devs.h, add those as comments instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7c77d648dac57b15b56f631bd8b2494676c00a8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add Kconfig option `SOC_INTEL_TIGERLAKE_S3` which will adjust
the ACPI to not offer D3Cold when using S3.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ieb1cc3d6a03cb452ff38ae393a993e881d9b5ff4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Software Connection Manager doesn't work with Linux 5.13 or later and
results in TBT ports timing out. Not advertising this results in
Firmware Connection Manager being used and TBT works correctly.
Linux patch:
c6da62a219
Tested on:
* StarBook Mk V
* System76 Oryx Pro 8
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib947c3c9cd843e54d4664509c15336178c0bc99e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Add support for VMCH and VMC of MT6366.
TEST=measure voltage 3.3V for VMCH and VMC
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Id8d98b6d827abd4713ee5c216941a9621422c7eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
1. Enable and setup USB drivers.
2. Pull up to a weak resistor for USB3_HUB_RST_L and we reset
the hub via GPIO149.
TEST=boot kernel from USB ok
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ifcc11d51b0c1e495477957111e6021ef8275f629
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
