nWR (Write-Recovery for AutoPre-charge commands), the programmed value of nWR
is the number of clock cycles the LPDDR4-SDRAM device uses to determine the
starting point of an internal Pre-charge operation after a Write burst with
AP (auto-pre-charge) enabled. For >2133MHz speed parts the nWR needs to
be set to 24 clock cycles. The nWR field, though, is only in the GLK
FSP, so just update that field conditionally based on the GLK Kconfig
option.
BUG=b:112062440
TEST= build test
Change-Id: I1147538f72f4e2f14e32f3657c05f1f505a56fbf
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In procedure generate_cpu_entries(), the code was copied from code that
could change variables "plen" and "pcontrol_blk" based on number of cores.
This is not the case with stoneyridge (2 cores only), and there's no need
to use the variables. Remove them and replace with fixed values.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I0258b19960b050e8da9d218ded3f1f3bfccad163
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27877
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In procedure pci_get_resource, when setting an IO mapped base address,
variable attr is &= with PCI_BASE_ADDRESS_IO_ATTR_MASK. However, in this
particular code flow variable attr is not used later. Remove the line.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: Ia4fdda1be92d22017a7a913a911db15aaa440b69
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The variable "begin" is extracted from the structure, but 4 lines below
it's overwritten with "end - size". This causes a static build scan error
that should be fixed. Remove the initial assignment of variable "begin".
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I0a265747e61289f045c5cac09e40478bd31e16fc
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27886
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The devicetree is not run through a C pre-processor, so remove it.
Change-Id: I161be45b2035f3a8724bf3217260e7571c429da8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27927
Reviewed-by: Naresh Solanki <naresh.solanki.2011@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This implementation updates the chip select control register
programming in gspi controller setup call to program the correct
bit fields for chip select state.
Change-Id: Ifab37b0003f09a680024d5b155ab0bb157920a53
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/27889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
cache_sync_instructions() has been superseded by
arch_program_segment_loaded() and friends for a while. There are no uses
in common code anymore, so let's remove it from <arch/cache.h> for all
architectures.
arm64 still has an implementation and one reference, but they are not
really needed since arch_program_segment_loaded() does the same thing
already. Remove them.
Leave it in arm(32) since there are several references (including in SoC
code) that I don't feel like tracking down and testing right now.
Change-Id: I6b776ad49782d981d6f1ef0a0e013812cf408524
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
coreboot payloads expect to be entered with MMU disabled on arm64. The
usual path via Arm TF already does this, so let's align the legacy path
(without Secure Monitor) to do the same.
Change-Id: I18717e00c905123d53b27a81185b534ba819c7b3
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch replaces the UART in the bootblock of SDM845 with a bitbang
implementation. Since SDM845 hardware UART needs a firmware blob loaded
into it before it becomes usable, it is not really suited for use in the
bootblock (since by the time we can read blobs from SPI, the bootblock
is essentially over anyway). This solution allows us to still have some
console output during early SoC initialization.
Change-Id: I0c252ec83a7993edce5c4debc687f1fdd0d7b36d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change bce49c2 (security/tpm: Improve TCPA log generation) missed
checking for NULL pointer before accessing the tcpa_table returned by
tcpa_log_init. This change fixes the boot hang observed on octopus by
ensuring pointer is checked for NULL before using it.
BUG=b:111403731
TEST=Verified that octopus boots up fine.
Change-Id: I2e46197065f8db1dc028a85551546263e60d46b2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Upper Map section in the descriptor contains a database of flash
chips (VSCC Table). Its offset is located at a fixed offset from
the beginning of the image. ifdtool falsely calculates the offset
from the descriptor signature which has moved by 16 bytes with
step b of the Ibex Peak (5 series) chipset. This produces bogus
output for all chipsets older than that.
This patch corrects the behavior by calculating the offset of
flumap by adding 4096 - 256 - 4 to the start of the image.
Change-Id: I14f029fe702c129dfd8069a58fbd41113700f7ef
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/27858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Apparently they were introduced when refining ICH7 support when
porting Kontron 986LCD-M and then copied over to ICH9 and 10.
Change-Id: I2d9ece608955310d22b79574b9113a1521b2076c
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/27855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
If GPP_E22(CABC_EN) remained floating GPI(SoC default) at V3.3_DX_EDP on,
it may cause damage on the GPIO pad.
To prevent, we would set this pad to GPO on romstage before EDP power on.
Since we need to cover all systems in market, I put it into romstage
instead of early_gpio_table.
BUG=b:111860510
BRANCH=poppy
TEST=Verified CABC_EN is set to GPO high 5ms before EDP power on
Change-Id: I34e2fe86329a88eb05e0ea3c6beac6a64754b41e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds variant callback to get GPIO configuration table in
romstage and configures these GPIOs before memory training is
performed.
BUG=b:111860510
BRANCH=poppy
Change-Id: I1eb51356fb3f4c0f4ff29b22dbcde6dbece303ad
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
AMD ALIB Function 1 accepts the AC/DC startup state. This
is reported to be required for AMD PSPP settings.
BUG=b:112020107
TEST= build test
Change-Id: Ibb6c872d84745217912956c15d6ca2e8ba387561
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27785
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds AML IccMax for VR configuration. From doc #594883, the
IccMax for Core was changed to 28A, we need this patch to accommodate
the changes. Besides, removes unused sku information from
sku_icc_max_mapping structure.
BUG=b:110890675
BRANCH=None
TEST=Remove icc_max from DT &
emerge-atlas coreboot chromeos-bootimage &
Tested with AML-Y and KBL-Y SKUs.
Change-Id: Ic22bae162b58b06b9519f1b708be55bde5e4641e
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27610
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update power limit1 value from 8W to 10W. There is an error
in the energy calculation for current VR solution on GLK.
Experiments show that when power limit1 set to 10W, gained
performance improvement with SoC TDP reaches max (6W) power.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ic320d442e7401e4be2e8e16d691db4c803f0fdc1
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
setup_spread_spectrum is called in early_init, meaning the console is
not initialized yet. So you won't see boot block booting twice.
BUG=b:111610455
TEST=booted grunt and verified that AmdInitReset does not reboot. I had
AGESA patched to skip the JTAG check.
Change-Id: Ia036ea513ac67d4b8bcf5a78029d969a4ae012a6
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
From doc 571118, the bit 5 of OdtConfig is nWR config.
If the bit 5 is set, MRC will set MR1 nWR field to 24.
If the bit 5 is clear, MRC will set MR1 nWR field to 6.
Change-Id: Ic8e4e2ffb098c8ba2f670535981e9a30c3d45b64
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/27814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the default value for Iccmax which is specified in vr_config.c.
The AcLoadline and DcLoadline keep the poppy value. Besides, the
USB 2.0 ports located on the mainboard are set to USB2_PORT_SHORT
and the others on the daughterboard are set to USB2_PORT_LONG.
Those setting need to be fine tuned later.
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: Icabfac04c94b3d480872c243d811509e274ef122
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gpio setting is based on the proto board schematics
BUG=b:111579386
BRANCH=Master
TEST=Build pass
Change-Id: I20fc081d372b8686f6128a7e85276f9c6798b199
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Kahlee based boards don't use SATA, so disable SATA on all boards to save
power.
BUG=b:112139043
TEST=Build and boot grunt, checked the absence of SATA PCI.
Change-Id: I6a12c03a5a95b1c8b40609a3fe656df92548b80b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Grunt boards don't use SATA, so it should be disabled to save power.
Check if SATA is enabled in devicetree, and enable/disable the device
based on that setting.
BUG=b:112139043
TEST=Buil and boot grunt, checked the absence of SATA PCI.
Change-Id: I4a3b5f65e612e8da5bedff0c557a0850f350dfa8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since only a handful of boards have descriptor blobs in the tree, it makes no
sense to have `HAVE_IFD_BIN` enabled by default then disabled on each mainboard.
This patch flips the default value of said variable, rendering all current
overrides unnecessary. The few boards which have an IFD in the blobs repo use
`select HAVE_IFD_BIN` to enable adding the IFD by default.
Since `HAVE_ME_BIN` depends on `HAVE_IFD_BIN`, the former has been removed
alongside the latter, and has been added to the boards with a ME blob as
`select HAVE_ME_BIN`.
Both `HAVE_IFD_BIN` and `HAVE_ME_BIN` have been removed from autoport as well.
Change-Id: I330c4886f8bea4b1a8ecad6505a0e5cc381654d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/27218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This patch contains the parts that changed the hash of the generated binary;
probably due to the compiler optimizing things slightly different.
Change-Id: I3233ba1747dcf5ad05b2ad771a86e3936f655d1c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This part of the cleanup patches changes the hash of the output binary; likely
due to the compiler optimizing things differently.
Change-Id: I1a22f6216a75e2b463d4e169e97ad6e0bbaafae8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27708
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On a a timeless build with coreboot i386 crossgcc 6.3.0, this doesn't change the
hash of the output binary.
Change-Id: I15e09320e72cffb8a2617eca0cfe40780f74bece
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27707
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code only compiled when REAL was set to 1; the other case included an
unpublished include.
Change-Id: I7f31e9cd02f45492d6c9e88ec6164a537ca5e3c2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27706
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to vendor's requirements LED 2 and LED 3 should be turned
off in late boot process. Add appropriate functions to read and
write GPIO status.
Change-Id: Ia286ef7d02cfcefacf0e8d358847406efe1496fb
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Change GPIO setting to use IOMUX to refer to GPIO by
IOMUX register as in BKDG for Family 16h Models 30h-3fh
Processor Rev 3.06.
Change-Id: Icf4a60acabe65cd7f9985bb3af8bd577764d4196
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Add Mailbox 3 driver
* Request brightness change through Mailbox 3
* Return Ones on error or if unsupported
* Mark existing code as legacy
(still required if no GMA driver is running)
* Call legacy code if Mailbox 3 is unsupported, on error or
if gma driver isn't running
Tested on Lenovo T430:
* Brightness control still works
* Brightness is the same on S3 resume
Change-Id: I51554c819148336b204d28972cbf775a10c3fb8a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/27711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
* Make tcpa_log_init static and move init code into
the tcpa_log_add_table_entry routine.
* Add more checks for log initialization.
* Fix minor issues
Change-Id: I215d79eed7ad17c6ab87f0c4b14a282e519ef07d
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/27769
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes the return type of gpio_base2_value() and related
functions from int to uint32_t. This makes more sense now that
board_id() and related functions (which are the primary use case) also
return that type. It's unlikely that we'll ever read a strapping of 32
GPIOs in a row, but if we did, we'd probably want to treat it as
unsigned.
Change-Id: I8fb7e3a7c76cb886aed40d0ada1f545180e43117
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove ACPI code which isn't necessary anymore due
to the LPC TPM ACPI generator.
Change-Id: I2fae286d61ec7c1036d1a8fa800dc8d9603252e9
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/27767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For some reason the PSPP setting was being overwritten in the common
code. Remove the setting and allow the oem customize function to
make the setting.
BUG=b:112020107
TEST= build test
Change-Id: If7f4511a71f725fedd60d33552656850e50d955d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested with GRUB 2.02 as a payload, booting Debian GNU/Linux 9.5 with
kernel 4.9. This code is based on the output of autoport.
The file `data.vbt` matches the VBT in the latest version of the vendor
firmware (version 4601).
This board works well under coreboot. A list of what works and what
doesn't can be found in the documentation part of this commit. To
summarise: the only known issues are that S3 suspend/resume doesn't
work, and that there is no automatic fan control via the super I/O.
Change-Id: I2a0579f486d3a44de2dd927fa1e76b90c3b48f62
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/27798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Ravi Sarawadi