For internal measurements this mainboard needs a marking inside the NC
FPGA when coreboot is ready and payload has been loaded.
Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
RISC-V is moving towards OpenFirmware-derived device trees, and the old
functions to read the config string don't work anymore. Use dummy values
for the memory base and size until we can query the device tree.
Change-Id: Ice13feae4da2085ee56bac4ac2864268da18d8fe
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On older Grus, GPIO0_A2 was an audio voltage rail enable line. On
Scarlet, we instead moved the audio codec enable (previously on
GPIO1_A2) there. Unfortunately the code still had some hardcoded
leftovers that were overlooked in the initial port and make our speakers
smell weird.
This patch fixes the incorrect GPIO settings and adds the speaker enable
pin to the GPIOs passed through the coreboot table, so that depthcharge
doesn't have to keep its own definition of the pin which may go out of
sync.
Change-Id: I1ac70ee47ebf04b8b92ff17a46cbf5d839421a61
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
CQ-DEPEND=CL:*496012
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I580567decfccd78366c37181255015ac2cd76493
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/22306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
From what I can tell FILECODE isn't used at all in this file.
Remove it.
Change-Id: Ie88140e63a4917f470f42119c1fe4e8c7d2584ca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
In skylake based platforms, setting GPIO pad reset config
to DEEP will reset the gpio configuration across warm reset,
set it to RSMRST to preserve the configuration across warm resets.
Also, moving the configuration from early to late as appropriate.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I38940b7c7d71e60bf0e51d6978a00be148ad61bc
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adapted from Chromium commit 12ad5b5: Reks : override USB2 Phy settings...
Base on Intel recommendation, override following
settings for USB2 port 1/2/3 on BSW D-stepping SOC.
1. Set USB[1] register for right side to 7321
2. Set USB[2] register for left side to 7021
3. Set USB[3] register for CCD to 7021
Original-Change-Id: I04240a010e875f29c47f4fea83ff918f180b0273
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iabd6312576e9897315c4e4dbf19341380d9d1414
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit 6ee6f3d: Reks: To set the RX ODT limit...
Override RX ODT and DRAM geometry for Micron part MT52L256M32D1PF-107.
Use get_ramid() to determine if override is necessary.
Original-Change-Id: I41f3aba030a00152e1217533ef953338ac396605
Original-Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Original-Reviewed-by: Kane Chen <kane.chen@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iea8c3c67e5afb21285dc15ad665474ad5f192423
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
ASL+ Optimizing Compiler/Disassembler version 20170831 shows the remark
below.
```
dsdt.aml 87: Method (_CRS, 0x0, NotSerialized)
Remark 2120 - ^ Control Method should be made Serialized \
(due to creation of named objects within)
```
So, serialize the method.
Fixes: commit 4a51ea8470 (google/kahlee: Add ASL for Elan touchpad)
Change-Id: I664f493318cbfd80d91565c0d29ec918278c4906
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Move files that are particularly specific to the mainboard into the
variant directory. Files that only have small areas of mainboard
specific pieces use #if to separate between the boards.
Add memory.c to split out the variant board id into a weak function.
Add baseboard/gpio.h to satisfy the build - this will be updated in the
next commit.
BUG=b:68293392
Change-Id: I7c1beb45f571f2547f3b5b0d7ec78923d0cec761
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The default setting for I2Cx is 400kHz. On this mainboard there is a
device on I2C0 which requires a lower clock rate to work correctly. For
this reason we set the frequency to 100kHz.
Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard has its own coreboot ready LED. The LED is switched on
via GPIO CNV_RGI_DT.
Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are PCI devices, which are connected to the PCIe
root port via a PCIe-2-PCI bridge. One of the devices only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 4 (Device 14.0).
The following routing is required:
INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA#
Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Current VBT setting for T8 is only 1ms which is under Innolux N116BCA-EA1
panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
CQ-DEPEND=CL:*493633
Change-Id: I7934b0f6d40b15796c55d360995c5eb0c5049222
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/22294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Leaving the wifi related gpios unmodified for now
due to FSP problem. If H0-H3 is configured as native mode
and GPIORXDIS, GPIOTXDIS bits in DW0 are cleared, it causes
FSP to assert when wifi module is attached. coreboot gpio
macros clears these 2 bits because they are suppose to be
"don't care" in native mode.
TEST=Boot to OS and verify wifi
Change-Id: Ica5e1c43802d04a9471cdfa0087e86f669122fff
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is to enable SPD word access to reduce boot time. It can save
80 ~ 100 ms per DIMM.
BUG=b:67021853
BRANCH=None
TEST=system boot, and boot time is reduced
Change-Id: Ic527a539ed634e15b939b18fff4b4e08ebb3ec57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For Raydium, export reset GPIO as well as PowerResource.
Let EN_PP3300_TOUCHSCREEN signal will goes to low at S3 mode.
BUG=b:67879912
BRANCH=coral
TEST=emerge-coral coreboot
Change-Id: Ibf501b40ecfc957fd8be7ebffd2357dfa0e07757
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/22252
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to have these separated.
BUG=b:64932381
Test=Build & Boot
Change-Id: I22898d3bf95d5e9a8fc2643bfccae1e2f5b29e44
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add new board librem15v3 as a variant of the librem_skl baseboard.
Changes from the librem13v2:
- Change board name and version
- Change GPIO A18, A19, A20, D9, D10 and D11 from NC to GPIO
- Enable PCI device 1c.4
- Change USB port definitions in devicetree
TEST: build w/SeaBIOS, boot PureOS on Librem 15 v3 hardware
Change-Id: I7c762a34f5b961c908e4a29ec331da4b0dea9986
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22048
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Convert the Purism Librem13v2 board to a variant setup,
in preparation of adding the librem15v3 as a new variant.
The 13v2 and 15v3 are nearly identical, so this minimizes new
code to add support for the latter.
Change-Id: I5d648cdb8f63c03de5474253203b3d0853673294
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22047
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It seems that recent changes in coreboot have fixed the raminit issues
on this board; the workaround of 10 ms delay after the S3 resume is not
needed anymore and can be removed.
Change-Id: If8fb97ecf3eb797f53270a053201fafd32031678
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/21485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Migrate the Librem13v2 from using FSP 1.1 to
the public/GitHub FSP 2.0 Skylake/Kabylake release:
- select FSP 2.0 in Kconfig
- adjust romstage/ramstage functions as required
- refactor pei_data functions
- remove VR_RING domain from devicetree (unsupported in FSP 2.0)
- add SataSpeedLimit parameter to work around power-related issue
when operating at SATA 6.0Gbps speed
TEST: build/boot Librem13v2, observe successful boot, lack of
SATA-related errors in dmesg.
Change-Id: Iedcc18d7279409ccd36deb0001567b0aa5197adf
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This commit just moves the vboot sources into
the security directory and fixes kconfig/makefile paths.
Fix vboot2 headers
Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Microcode blob has been updated, so update the length to match
Change-Id: I46ac10e5c6cd6492c98a7034649797f301101abc
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The USB settings were wrong in some places, or missing and the
USB_OC values were taken from the schematics.
Change-Id: I29b564a4161c486f5e8556b1726471bfa2351b7a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The RComp values have been updated to match what is shown in the schematics.
Extracting the Memory configuration blob from the original BIOS (A blob
which contains the correct binary sequence matching the RComp values appears
in object with GUID 2D27C618-7DCD-41F5-BB10-21166BE7E143), I could find
and confirm the DQ and DQS mapping.
Small code cleaning in romstage.c with no effect.
Change-Id: I35c734269b365fd759e9bd56224a80a8a8df5a57
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Check CBFS for 'serial_number' field, and use value if exists;
otherwise use value set at compile time.
Change-Id: I4b50f6310ca32b9dd372db075a5b5729e3b06619
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22040
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the missing device and ensure it shows up in the devicetree prior
to PCI enumeration.
Change-Id: Ia2c4ba1200422b36c533e86065a4fcd10c4b2722
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the missing device and ensure it shows up in the devicetree prior
to PCI enumeration.
Change-Id: I44c7df6a2be149ed61094f67ef1c578736e5b55c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add GPE configuration table.
Remove GPE3 from the power button ASL and set the EC to GPE3(AGPIO22).
Set the EC and PCIE/WLAN SCI GPIO signals.
Set GPE ASL methods for:
PCIE/WLAN 8h
EHCI 18h
XHCI 1fh
Note EC GPE3 methods are in the EC ASL.
BUG=b:63268311
BRANCH=none
TEST=Test lidswitch powers the device on and off at the login screen.
Change-Id: I27c880ee84b6797d999d4d5951602b654ede948e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22096
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set PL2 based on either 90% of usb c charger's max power or sku id if
using a barrel jack.
BUG=b:37473486
BRANCH=None
TEST=output debug info for different skus and make sure
PL2 set correctly.
Change-Id: I487fce4a5d0825a26488e71dee02400dbebbffb3
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/21772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Stoney Ridge has one EHCI controller and one XHCI controller.
Also, update the Kahlee and Gardenia mainboards ASL to match.
Change-Id: I5749ca0640796732e74e551147f8c4446317b77e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change the board name from cannonlake U DDR4 to U LPDDR4 to match
actual platform.
TEST=NONE
Change-Id: Id350e3cbc299d49431197ef5f914ea9a7310a0a5
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Include common platform.asl to have generic indication of power
transition state of system.
TEST=Enter and resume from S3, check the post code had been changed to
0096 and 0097.
Change-Id: Ic38ac6d7e60441caeba5c088c9dbe4d901355782
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22111
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
