Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Some of these will move to EARLY_CBMEM_INIT.
Change-Id: Ia969e30ad7097860180bd047eaf81859a42a747c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
Remove obsolete code. The same settings are always done in southbridge.
Change-Id: Ic893ddbace73ae8b122c4fb675febc7d1e0b5da9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Note that all boards incorrectly had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
On this device libgfxinit successfully initializes textmode and
framebuffer mode on the device connected to the HDMI1 port.
VGA port is not tested, due to lack of VGA with valid EDID.
Every ports works on GNU/Linux with kernel version 4.9+80+deb9u1.
Due to limitations within the libgfxinit's current build system,
it needs "select NORTHBRIDGE_INTEL_IVYBRIDGE" to work, even it is
PCH instead of CPU for which libgfxinit should be configured here.
Change-Id: Ib1513fc57b79eebc5d047c2e24585731c44bc215
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All affected boards did the same USE_NATIVE_RAMINIT distinction or
actually selected USE_NATIVE_RAMINIT. Also update autoport.
Change-Id: I924c43cec1e36e84db40e4b8e1dd0e05cad2b978
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20813
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Romstage of many 440BX boards included headers that are not used.
Remove them as part of a bigger cleanup effort.
Change-Id: I89ddeda3c90e1a4907c05851185b69f3b29e54ba
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Switch from lapic to tsc.
Allows timestamps to be used in coreboot, as there's a reference
clock available to calculate correct time units.
Clean Kconfig, remove duplicated lapic code and include tsc dir for
LGA1155 boards.
Tested on Lenovo T430.
Change-Id: I849ca2b3908116d9d22907039cd6e4464444b1d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
* Rename it to HAVE_VGA_TEXT_FRAMEBUFFER.
* Let drivers select it if they are in charge.
* Don't select it on the mainboard level if a driver handles it.
Change-Id: I2d9d09be9aa6d019e77460e69a245ad2d8cda4ea
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Do not lock ETR3 CF9GR in early romstage.
As of Change-Id: I2cb30267a6342db1f3b11715034219ffb18ca678 this is done
in bd82x6x's finalize handler.
Change-Id: Iea091511f0d2a6128d3a19e9413090c85e4c2e57
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This board features a PATA port.
TESTED PATA drive works in SeaBIOS and OS.
Change-Id: I74dc72c22e6c4fed07f28ef7d88adde54656ae39
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently only one board uses this northbridge in coreboot but some
patches are pending to add more.
Change-Id: If035e442d1a23674667f46a07b44c4f2b81be48c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested against a lenovo-manufactured tpm 1.2 module:
a /dev/tpm0 visible inside GNU/Linux, but there is no menu items in
SeaBIOS' interface, which seems a common issue of SeaBIOS on ivb boards.
Change-Id: Id0dee74d945bae5d77eb669d8b9d468a67aee508
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19521
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently native video init works on port HDMI1 (wired to the
on-board DVI-D socket) , HDMI3 (the on-board HDMI port), and the VGA
port, both text mode and fb mode.
Every ports works on GNU/Linux.
Tested against an IVB cpu (i7-3770T).
Change-Id: If00a7247df0c32b3d1f489fb92d86baaa8fdf8ba
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The AFC—Additional Flash Control Register is set by
southbridge code.
Remove redundant calls and get rid of it in autoport.
Change-Id: I627082e09dd055e3b3c4dd8e0b90965a9fcb4342
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19493
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This needs some extra headers in amdk8/raminit.c that were otherwise
provided by that file.
Change-Id: I80450e5eb32eb502b3d777c56790db90491fc995
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19360
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
For this debug.c needs to be linked too.
Change-Id: I9cd1ffff2c39021693fe1d5d3f90ec5f70891f57
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19030
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All boards select INTEL_EDID, move it to nb folder.
Change-Id: I35f075a87f2d841856b208f9440cf41af6a3c8e6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19086
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It rewrites the results of receive enable stored in the upper nvram
region, to avoid running receive enable again.
Some debug info is also printed about the self-refresh registers.
(Not enforcing a reset here, since 0 does not necessarily mean it's
not in self-refresh).
Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17998
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Previously the raminit failed on hot reset and to work around this
issue it unconditionally did a cold reset.
This has the following issues:
* it's slow;
* when the OS issues a hot reset some disk drives expect their 5V
power supply to remain on, which gets cut off by a cold reset,
causing data corruption.
To fix this some steps in raminit must be ommited on the reset path.
This includes receive enable calibration.
To achieve this it stores receive enable results in RTC nvram for them
to be rewritten on the resume path.
Note: The same thing needs to be done on the S3 resume path.
Calling a hot reset after raminit "outb(0x6, 0cf9)" works.
Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18009
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is more consistent with newer Intel targets.
This a static struct so it is initialized to 0 by default.
To make it more readable:
* only setting to GPIO mode is made explicit;
* only pins in GPIO mode are either set to input or output since this
is ignored in native mode;
* only output pins are set high or low, since this is read-only on
input;
* blink is only operational on output pins, non-blink is not set
explicitly;
* invert is only operational on input pins, non-invert is not set
explicitly.
Change-Id: I05f9c52dee78b7120b225982c040e3dcc8ee3e4e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17639
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The console output is garbled until it is fixed in ramstage
by devicetree which sets the uart clock predivider correctly.
Change-Id: I6d6ec0febfec98a8d4a71e1476036c804cf5f08d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17969
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Previously, all romstages for this northbridge family
would compile via 1 single C file with everything
included into the romstage.c file (!)
This patch separates the build into separate .o modules
and links them accordingly.
Currently compiles and links all fam10 roms without
breaking other roms.
Both DDR2 and DDR3 have been completed
TESTED on REACTS: passes all boot tests for 2 boards
ASUS KGPE-D16
ASUS KFSN4-DRE
Some extra changes were required to make it compile
otherwise there were unused functions in included "c" files.
This is because I needed to exchange CIMX
for the native southbridge routines. See in particular:
advansus/a785e-i
asus/m5a88-v
avalue/eax-785e
A followup patch may be required to fix the above boards.
See FIXME, XXX tags
Change-Id: Id0f9849578fd0f8b1eab83aed910902c27354426
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/17625
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Currently, some Intel 945 boards miss some or all of the time stamps
*1:start of rom stage*, *2:before ram initialization*, and *3:after ram
initialization*, so add them.
Use the same formatting as used for the board Lenovo X60, which already
has code for all the time stamps.
Change-Id: Ie25747d02fadd74b7d7b7cab234a7a88b2cc0c42
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17993
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If the cmos checksum is incorrect it should fall back to sane defaults.
Change-Id: If16cfc73effd4a825d0cefcd30bfd0e48b2d9132
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17968
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Checking for memory self refresh can generate false positives,
as explained in faa6beb: "northbridge/intel/i945:
CHECK_SLFRCS_ON_RESUME Kconfig option".
This seems to be the case for this motherboard.
TESTED on ga-945gcm-s2l.
Change-Id: Iadf0a73b054470b652e1dc02557fb1715131f823
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17617
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of hardcoding pci_mmio_size in the raminit code,
this makes it a parameter in the devicetree.
A safe minimum of 768M is also defined since using anything
less causes problems (if 4G of ram is used).
Change-Id: If004c861464162d5dbbc61836a3a205d1619dfd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16856
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
Change-Id: I943e354af0403e61263f1c780f02c7b463b3fe11
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17529
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This mainboard is identical to ga-945gcm-s2l except for NIC
which is a Realtek RTL 8101E chip (10/100 Mbit).
The schematics of ga-945gcm-s2l mention multiple NICs and ga-945gcm-s2c
and ga-945gcm-s2l have a common manual further indicating that those
boards are close to identical.
Change-Id: Iba3d401efcf208154e639c3237b201830a5151aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17416
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This motherboard support Intel core 2 quads.
Before this change SeaBIOS was not usable, due to it crashing before it
got to load anything.
Change-Id: Ifdaaceace04f9ba0753aab2d3b05c0519367f91f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17537
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
