Mainboards can configure gpios in their smihandler.
BUG=b:180507707
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I6c2b28f981f580cfb6f982a2d7e4c309d6f82e0b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change will allow for GEVENTs to be used in ASL code.
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I77abd134555c21a32a302ee92cd080284cd2e634
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If bit 0 of byte 0x47 is set FSP will perform full memory training
even if previously saved data is supplied.
Up to and including FSP 2021 WW01 it was reset internally at the end
of PostMemoryInit. Starting with WW03 this is no longer the case and
Intel advised that this bit should be reset externally if valid MRC
data is present.
Change-Id: I9c4191d2fa2e0203b3464dcf40d845ede5f14c6b
Signed-off-by: Deomid "rojer" Ryabkov <rojer9@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=b:180456030
TEST=`mosys` is able to detect the platform correctly
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ifbaa4a380bdb546bb54d579b46fe5760b2f4b754
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
BUG=b:181887865
TEST=`crossystem` shows correct state of WP signal when toggled
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If49ca1d70cc36ab74d70e858336679c0a9a3258e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The default value for the LidStatus is "LidClosed" mean 0
Because of this GOP skips graphics initialization assuming
lid is closed even though lid is open. This Patch is to set
LidStatus UPD to 1 whenever RUN_FSP_GOP config is selected.
BUG=b:178461282
BRANCH=None
TEST=Build and boot ADLRVP and verify eDP is coming up in
depthcharge
Change-Id: I1648ae0f06e414b2a686e325acf803deb702b7a5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Move PRERAM_CBMEM_CONSOLE to SRAM L2C and increase its size from 15K to
400K. With this change, most part of the DRAM full calibration log can
be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST=Hayato boots
BRANCH=none
Change-Id: I896884d298e197149f75865e9d00579124a34404
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Many header files and helper macros have been moved to the
common folder and we want to use them in mt8173/mt8183
DRAM calibration code.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: Ifa483dcfffe0e1383cb46811563c90f0ab484d5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51224
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To reduce qualification effort, we want to pre-populate DRAM by their
size, package type and geometry so when a new DRAM is introduced we
don't need to spin off a new firmware release.
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I42ee170c159e551e840ab4e748f18f5149506b4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mediatek has released the reference implementation for DRAM
initialization in vendorcode/mediatek/mt8192/dramc (CB:50294)
so we want to use it to replace the derived calibration code
in soc folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I2b2f41d774c6b85f106867144fb0b29a4a1bdfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This is the DRAM initialization code from the reference
implementation released by Mediatek for MT8192.
The DRAM calibration code can be taken as a standalone
library, used by different boot loaders for initializing
DRAM and following a different coding style (coreboot was
using Linux Kernel coding style), so we have to put it
in vendor code folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I3853204578069c6abf52689ea6f5d88841414bd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Performing ME finalization in SMM does not seem to be required.
Tested on Asrock B85M Pro4, ME still gets finalized successfully.
Change-Id: I9fde40a54f3fb8da2fba46c531443fdd2e067077
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use the common PCIEXP_HOTPLUG code to generate a dummy device for PCIe
ports supporting hotplug. This allows to have control over how much
resources are allocated to hotplug ports.
Tested on thinkpad X220: now hotplugging a dGPU via the expresscard
slot sometimes works.
Change-Id: I3eec5214c9d200ef97d1ccfdc00e8ea0ee7cfbc6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph
`bincfg` is not creating anything new, it just converts
from text to binary.
Change-Id: I14e67ee8bc449d171a951f6edeaa9f9d0c04dbe1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51319
Reviewed-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change moves GPE configuration from brya0/overridetree.cb to
baseboard/devicetree.cb since all variants will end up using the same
configuration.
TEST=Verified using "abuild -p none -t google/brya -b brya0
--timeless" that coreboot.rom generated with and without this change
is the same.
Change-Id: Ie31bf2bf8a91da82fca77c78fb0a735a2645de55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change updates MAINBOARD_PART_NUMBER string to use uppercase for
first character. This matches what all others boards do.
BUG=b:180456030
Change-Id: I10eaeef5ec662a5718b787a3f0e3705cf70d751d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51297
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement the mainboard_tcss_get_port_info weak function so that the TCSS
muxes can be properly configured to ensure mapping is correct in mux. This
ensures that any devices that are connected during boot are not improperly
configured by the Kernel.
BUG=b:180426950
BRANCH=firmare-volteer-13672.B
TEST= Verified that the SOC code that initialized TCSS muxes to disconnect
mode is executing properly for all TCSS ports and verified that USB3 devices
are no longer downgrading to USB2 speed if connected during boot.
Change-Id: I59e5c5a7d2ab5ef5293abe6c59c3a585b25f7b75
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TCSS muxes being left uninitialized during boot is causing some USB3
devices to downgrade to USB2 speed. To properly configure the Type C ports
the muxes should be set to disconnected state during boot so that the port
mapping of USB2/3 devices is properly setup prior to Kernel initializing
devices.
BUG=b:180426950
BRANCH=firmware-volteer-13672.B
TEST= Connected USB3 storage device and rebooted the system multiple
times to verify that devices were no longer downgrading to USB2 speed.
Change-Id: I4352072a4a7d6ccb1364b38377831f3c22ae8fb4
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use lowercase `port` in both the spec and the body.
Change-Id: I3d1e2abe03eedcaf57716af444a3e3b8a61b60d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Continue unifying Lynx Point and Wildcat Point (PCH for Broadwell) code.
Define the WPT-LP SMBus PCI device ID, add it to smbus.c of Lynx Point,
and drop all now-unnecessary SMBus code from Broadwell.
Change-Id: I864d7c2dd47895a3c559e2f1219425cda9fd0c17
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add marshaling and unmarshaling support for cr50 vendor sub-command to
reset EC and a interface function to exchange the same.
BUG=b:181051734
TEST=Build and boot to OS in drawlat. Ensure that when the command is
issued, EC reset is triggered.
Change-Id: I46063678511d27fea5eabbd12fc3af0b1df68143
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
BUG=None
TEST=Build the blipper board.
Change-Id: Ia7e4c1d5c06013c1902816d6dcafb5a8a0386bb3
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The datasheet indicates that this bit is reserved. However, subsequent
patches need to use this macro in common code, or else builds fail. To
iron out this difference, mask out the bit in `soc_get_smi_status`, so
that common code always sees it as zero. Finally, add an entry for the
bit in `smi_sts_bits` for debugging usage, noting that it is reserved.
Change-Id: Ib4408e016ba29cf8f7b125c95bfa668136b9eb93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. No gpio control in bootblock
2. Power on and then deassert reset at the end of ramstage gpio
3. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #3 and wrapping
around to #2.
This change affects the following volteer variants that include an FPMCU:
1. Drobit
2. Eldrid
3. Elemi
4. Halvor
5. Malefor
6. Terrador
7. Trondo
8. Voema
9. Volteer2
10. Voxel
BUG=b:178094376
TEST=none
Change-Id: Ib51815349cea299907c10d6c56c27bd239e499e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The original implementation of early tcss resulted in calling to mainboard
then back to soc then back to mainboard to properly configure the muxes.
This patch addresses that issue and instead just gets all the mux
information from mainboard and does all config in the soc code.
BUG=none
BRANCH=firmware-volteer-13672.B
TEST=Verified functionality is not effected and early TCSS still functions
Change-Id: Idd50b0ffe1d56dffc3698e07c6e4bc4540d45e73
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`pmc_send_ipc_cmd()` expects the caller to pass in a pointer to a valid
request and response buffer. However, early_tcss driver was passing in
a NULL pointer for response buffer which would result in invalid
access by `pmc_send_ipc_cmd()`.
Currently, the response buffer is not used in `update_tcss_mux()`. So,
this change drops the passing of `rbuf` parameter to `send_pmc*`
helpers and instead uses a local `rsp` variable in the respective
functions. All the PMC functions used in early_tcss driver return some
kind of response. These should be checked to return appropriate
response code back to the caller. However, this needs to be done as a
separate change.
Change-Id: I215af85feed60b6beee17f28e3d65daa9ad4ae69
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With the aliases some of the comments are redundant. I'm still not sure
if the Ethernet controller on the embedded SKUs supports 10G or only 1G.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1e432c12f92a622f8ee05be19acb2c304dd74afb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Since the support for the GSMI ELOG isn't implemented in the SMI handler
yet, the corresponding code isn't added to fch_slp_typ_handler in this
patch.
BUG=b:181766974
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia27b2486dde1a373607ce895a975e873d9026ba1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
In commit 2609eaaa8f (src/drivers/i2c/rx6110sa: Omit _HID temporarily)
the randomly assigned and therefore wrong ACPI ID for RTC RX6110SA was
removed. In the meantime Seiko-Epson did a great job and registered an
official vendor ID in the ACPI database [1]. Further on, Seiko-Epson
has now assigned the unique Product Identifier for the RX6110SA, which
is '6110'. The assignment of the Product Identifier is controlled by
the vendor and there is no official database where this ID is stored
in. It is up to the vendor to make sure that this ID stays unique.
This patch adds this new vendor and product ID to the driver. Together
with a pending Linux patch this RTC is now useable as ACPI device in
Linux.
[1] https://uefi.org/ACPI_ID_List?search=SECC
Change-Id: I45838162f014a760520692c6dcaae329ad98547d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51176
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mathew King