The possibility of adding a bootsplash image to ROM should be independent
from VGA_ROM_RUN and VESA menuconfig options.
For example, the stored image could be saved in CBFS not for coreboot
but for later use in SeaBIOS.
Change-Id: I3a0ed53489c40d4d44bd4ebc358ae6667e6c797f
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/12129
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
LPC decodes were not enabled, leading to a failure of POST 80 cards
and similar debugging devices. Enable the relevant LPC decodes
to allow debugging.
Additionally, the SMBUS controllers were not properly set up.
Enable both the primary and auxiliary controllers.
Finally, K10 and higher CPUs were hanging during boot due to
a misconfigued IOAPIC. Properly configure the IOAPIC.
Change-Id: I9ffb6542ce445ac971fb81f4f554e7f1313e6a98
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12177
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Certain devices, such as the Intel 82575GB, contain multiple nested
PCIe bridges (for example the PES12N3A). Coreboot does not set
the primary bus number of the lower bridges, causing upstream
forwarding failure. This in turn causes coreboot to fail to find
the lowest devices (in this case the NICs), and as a result the
required resources are not allocated and the NICs do not function.
Change-Id: I4fd3aa21a04dbe89ac6a5995e7707af914d432b1
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12186
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
- Display what's happening to the console as well as logging to the
junit.xml file.
- Log the clean in the junit.xml file so if it fails it doesn't just
appear to not have run the test.
- Run both clean and distclean (if distclean exists and runs clean,
this still only runs clean once) so that if distclean doesn't exist
the clean still happens. Don't stop the build if the clean step
fails in case there's no distclean in the util makefile.
- Run the util builds multithreaded. This saves a couple of seconds
and helps find dependency issues that might not be seen if building
single-threaded.
Change-Id: If895295c83faba98661b7c925b65fd436e06b834
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12121
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Have clean remove junit.xml files.
- Remove junit.xml target from cbmem makefile - this is in the top
level Makefile.inc now.
- add distclean targets to makefiles.
- Make sure all makefiles have .PHONY set up.
- rm commands need -f or they will fail if the file they're trying
to remove doesn't exist, causing the build to fail.
Change-Id: I2f0635f2c0a9417e3377a90c8d67103323c4a72f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12120
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Update mainboards using the w83795 sensor device with sane default
values. Note that in some cases the defaults may vary from the
defaults provided by the old driver, for example the default fan
speeds and control modes have changed as I do not have any information
on the correct sensor to fan mappings for these boards.
Change-Id: Id2ad6222d7a0f29483b022fa097d7d098c6b4122
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12124
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Add full support for fan control, fan monitoring, and voltage
monitoring. Fan speeds and functions are configurable via
each mainboard's devicetree.cb file.
NOTE: This patch effectively rewrites large portions of
the original driver. You may need to re-verify correct
operation on your hardware if you were using the old
driver code.
Change-Id: I3e246af0e398d65ee43ea708060885c67fd7d202
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11936
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
If an SMBUS device in devicetree.cb is placed under a parent device
that does not have an SMBUS controller, coreboot will enter an
infinite loop and hang without printing any failure messages.
Modify the loop to exit under these conditions, allowing the failure
message to be printed.
Change-Id: I4c615f3c5b3908178b8223cb6620c393bbfb4e7f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Add minimal Makefile based on cbmem’s Makefile.
The make target `junit.xml` is removed as this is handled differently
since commit de9adebb (Add junit.xml code to top Makefile.inc instead of
utils).
Also the `junit.xml` is removed in the make target `clean`.
Additionally, the make target `distclean` is added, as the current
junit.xml code in the top `Makefile.inc` requires that.
Change-Id: I164b1f7733505bca6248d0711d7ad71d635fa926
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11876
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Auron only has three GPIOs for RAMID, so there is no need for
sixteen SPD file entries. Only include 8 SPD entries.
Change-Id: Icf83719a2a5b9271b29f48cde5c66c4c8ccd07f4
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12073
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On Broadwell, this reduces the number of 'remarks' in the IASL build
from 222 to 3.
Fixes these remarks:
Object is not referenced (Name is within method [_CRS])
The ACPI compiler is trying to be helpful in letting us know
that we're not using various fields in the MCRS ResourceTemplate
when we define it inside of the _CRS method. Since we're not
intending to use those objects in the method, it shouldn't be an
issue, but the warning is annoying and can mask real issues.
Moving the creation of the MCRS object to outside of the CRS
method and referencing it from there solves this problem.
This change was made for fsp_baytrail in commit 2eaa0d49
fsp_baytrail: Fix ACPI 'Object is not referenced' warnings
Change-Id: I67a1faf963d1868f4133c7747a43a511cd28a44b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ifb434db1b8eb01acf48f26366c5237ae49a8730a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ide50b34184b80c86b996f86dd589c3cf3bf75587
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: I1e69cf0fd73e70ed6656b9ed6f55aba4c56a6edd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11882
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Before this fix the value of PcdEnableSdio was printed as the MIPI/ISP
configuration option.
TEST=Built and booted on Minnowboard Max
Change-Id: Ia9b02d520f4e615f90b45935456b9d97c5d00f11
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: http://review.coreboot.org/10126
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
connections checked by desoldering the FCH and looking at the PCB
this lowers the power consumption by about 150-200mW measured on primary side
based on change #5397
Change-Id: I986c4cc73a247994f2a47fdfd03f585069ca9385
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/11866
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch fixes compilation of cbfstool on Cygwin.
As reported in http://review.coreboot.org/#/c/10027
cbfstool on Cygwin likes to be compiled with -D_GNU_SOURCE.
That patch was abandoned because it would unwantedly turn on
more GNU extensions. Instead of doing that, only enable the
define on Cygwin, switch to -std=gnu99 instead of -std=c99 to
make fileno and strdup actually available.
A MINGW32 check that was forgotten in Makefile was copied over
from Makefile.inc to keep the two files in sync.
This patch has no impact on non-Windows builds.
Change-Id: I068b181d67daf9c7280110e64aefb634aa20c69b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11667
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
don't use non-volatile pointers for MMIO access
Change-Id: I9f38012a806e43f2535265f1d25537c59b53904e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12081
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The reintroduction of cougar_canyon2 crossed beams with the
moving the GMA display brightness data in ACPI into individual
mainboards.
Make things build again by having the board use the same default values
that it used to use automatically. They may be wrong, but no worse than
what was there before.
Change-Id: Id788034c38b42e1c35d9cd17e9bbb2ce49e3e91c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12132
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This utility should make it easier to complete and maintain
the database of coreboot subsystem maintainers (MAINTAINERS
file)
This will need a bit of tender love and care to print information
in an easily machine readable output for the build system, but its
a first start to query the maintainers database.
Build with:
$ go build util/scripts/maintainers.go
Find a maintainer for a set of files with:
$ ./maintainers Makefile Makefile.inc
Makefile is in subsystem BUILD SYSTEM
Maintainers: [Patrick Georgi <patrick@georgi-clan.de>]
Makefile.inc is in subsystem BUILD SYSTEM
Maintainers: [Patrick Georgi <patrick@georgi-clan.de>]
Check the maintainer database with:
$ ./maintainers
.gitignore has no subsystem defined in MAINTAINERS
.gitmodules has no subsystem defined in MAINTAINERS
.gitreview has no subsystem defined in MAINTAINERS
3rdparty/arm-trusted-firmware has no subsystem defined in MAINTAINERS
3rdparty/blobs has no subsystem defined in MAINTAINERS
3rdparty/vboot has no subsystem defined in MAINTAINERS
COPYING has no subsystem defined in MAINTAINERS
Documentation/AMD-S3.txt has no subsystem defined in MAINTAINERS
Documentation/CorebootBuildingGuide.tex has no subsystem defined in MAINTAINERS
Documentation/Doxyfile.coreboot has no subsystem defined in MAINTAINERS
[..]
Change-Id: I49c43911971152b0e4d626ccdeb33c088e362695
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12119
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Konstantin Aladyshev