When the BMC firmware module is installed on the KGPE-D16, the
RAM SPD multiplexer lines are disconnected by hardware from the
SP5100 GPIOs and attached to BMC GPIO lines instead.
Set the BMC GPIOs to match the state of the SP5100 GPIOs during
RAM setup.
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac5
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/19820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The device ID is documented in "Intel Xeon Processor E3-1200 v3
Product Family Datasheet volume 2" section 2.2.
Tested with ASRock H81M-HDS with Xeon E3-1271 v3. SeaBIOS payload can
find the boot devices, and GRUB payload can boot Debian GNU/Linux on
the SATA disk.
Change-Id: I999391c9bbc6b39526ad7aec8a6d8fe1a9b5f921
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The Intel GMA ACPI opregion address needs to be set on S3 resume,
otherwise the Windows display driver fails to re-initialize correctly.
Fix by ensuring the address is set correctly regardless of display
init type used (GOP or VBIOS).
Test: build/boot on google/edgar, ensure internal display functional
following S3 resume under Windows 10.
Change-Id: I471c44e8ba4514e4a2ddf6739109b759145598ed
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Mirrors addition to Braswell SoC in commit d3d0f07.
Test: build/boot Windows 10 on Baytrail ChromeOS device, verify Windows shows
virtualization as enabled.
Change-Id: Ia1fafa73325814fed30b2ac91290b682dd8eab04
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In commit eceba31c7f ("util/lint: Set "acknowledgement" correct"), the
word "acknowledgement" was removed from util/lint/spelling.txt. A more
robust solution is to comment it out, as done for "sepc" in commit
afa5ec8d5f ("util/lint: Update spelling.txt to latest linux version").
Change-Id: Ia976dedc9b31190d22e7b946f14709d5c4577f71
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
They are hopefully stable enough by now.
TEST=Building with for emulation/spike-riscv with BUILD_TIMELESS,
with and without this patch, results in the same coreboot.rom.
Change-Id: Ie6747c7eeea6cd8fd2138c5ba535a08c5add9038
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
util/util_readme/util_readme.sh is specifically a bash script and
requires bash-specific features such as "[[". It doesn't work when run
with a "sh" shell that only implements POSIX features, such as dash.
Thus, tell the user to run the script directly, in which case the #!
line is used.
Change-Id: I5706ffe857c5a148e9776571a377ad8647f9a4c2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
94b761c8e (util/board_status: run dmesg with sudo) attempted to
fetch the console as root locally but instead sudo was put in front
of the remote path which runs as root anyways.
Also unless quotation marks are used the cmd function will see 'sudo'
and 'dmesg' as separate aruguments.
Change-Id: Ib9e9e4b443f4e3ad04c5fda2c2ce626255a190f2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Bobba would prefer to use different SAR values per sku-id for regulatory
compliance. This commit uses the newly added interface for custom wifi
SAR CBFS filenames.
CQ-DEPEND=CL:*729429
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: I354382d651d65d533459f0ca460ca6fd6de547fd
Reviewed-on: https://review.coreboot.org/c/30223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Using a fixed filename only allows for one SAR configuration to be
checked into CBFS. However, we have devices with shared firmware that
would desire separate SAR configurations. This change allows boards to
define a function to select one of multiple files stored in CBFS to be
used.
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: Ib852aaaff39f1e9149fa43bf8dc25b2400737ea5
Reviewed-on: https://review.coreboot.org/c/30222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It seems they are not included anywhere, Jenkins?
Change-Id: I629cdeb337fce381c69bd1ba0520e524ccdd90dd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/26756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enaebl the RTC driver to be used on mc_apl4.
Change-Id: Ib8d2a9f6b8cea47cd10db4dfcc59eec1b21c7993
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
This function returns APIC id for respective cpu core.
BUG=b:74436746
BRANCH=none
TEST=mp_get_apic_id() can be accessed in other files now.
Change-Id: I5c5eda8325f941ab84d8a3fe0dae64be71c44855
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/25620
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements board reset on the Cheza board. The real board
reset used by the operating system uses the PMIC, but unfortunately the
PMIC needs to be configured right for that to work. The PMIC
configuration currently happens in the Qualcomm blob (QcLib) that is run
from romstage, but vboot needs to be able to reboot during verstage
already. Porting all the PMIC initialization code to run in the
bootblock seems excessive (and at odds with the goal of doing as little
as possible before verification), so we'll just do a little hack and ask
the EC to perform a cold reset instead. For vboot purposes, this should
work just as well.
BUG=b:118501305
TEST=Hacked vboot code to call vboot_reboot(), confirmed that board
reset and came back up as expected.
Change-Id: I3858d95f481884a87c243d4fa3d6369c1e8a5a2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO pin map for CNL-H does not match with the OS expected
pin numbers. This has been updated to match what is used by the
Linux kernel pinctrl driver and the pad base has been set for
the GPIO groups to match the sparse GPIO map used by the kernel.
I do not have CNL-H hardware to test this so it is verified against
the kernel driver at drivers/pinctrl/intel/pinctrl-cannonlake.c
Change-Id: Ife7d3090d654b0b88c6911befa08bf6abd4f2ff9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30134
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO drivers in Windows and Linux for the Cannonlake CPU
have a sparse GPIO map and do not allocate pins contiguously.
Each GPIO group is allocated as 32 pads regardless of whether
the hardware actually has that many in the group.
It appears this originated with a bug in Windows/UEFI and was
carried over to Linux in order to work with existing firmware:
https://lore.kernel.org/patchwork/patch/855244/
In order to support using ACPI GPIOs it is necessary for coreboot
to be compatible with this implementation. The GPIO groups that
are usable by the OS are declared with a pad base which is then
used to compute the number for ACPI GPIOs.
BUG=b:120686247
TEST=tested with write protect GPIO on sarien board. Before this
change the ACPI pin number was 220 which did not correspond to the
pin number in Linux. After this change the ACPI number is 303,
which maps to the correct GPIO in Linux. Now the GPIO value reported
by the kernel changes when the WP pin is toggled in hardware.
Change-Id: I4f1a9e118d7e48f2445ccbb62a12a22e9a832c51
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If the generic GPIO library is enabled the code that generates the
GPIO table in ACPI should attempt to get the GPIO pin value from
the gpio_acpi_pin() function.
BUG=b:120686247
TEST=Tested on Sarien board to ensure that GPIO pin exported by
Chrome OS for the Write Protect signal is correct.
Change-Id: I267694b576009f79bacac6eda5f32bbf51742d78
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In some situations the GPIO pad numbers used by the OS are not
contiguous and coreboot must provide a way for ACPI to provide
the expected GPIO number to the OS.
To do this each GPIO group can now have a pad base value, which
will be used as the starting pin number for this group and it
is added to the relative pin number of this GPIO to compute the
ACPI pin number for a particular GPIO.
By default this change has no effect because the existing uses
of INTEL_GPP() will set the pad base to PAD_BASE_NONE and the
GPIO number is used as the ACPI pin number without translation.
BUG=b:120686247
TEST=tested on a sarien(cannonlake) board
Change-Id: I25f73df45ffae18c5721a00ca230a6b07c250bab
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30131
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch introduces 3 helper function for cpuid(1) :
1. cpu_get_cpuid() -> to get processor id (from cpuid.eax)
2. cpu_get_feature_flags_ecx -> to get processor feature flag (from cpuid.ecx)
3. cpu_get_feature_flags_edx -> to get processor feature flag (from cpuid.edx)
Above 3 helper functions are targeted to replace majority of cpuid(1)
references.
Change-Id: Ib96a7c79dadb1feff0b8d58aa408b355fbb3bc50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I64e79904c7ad95091ea29d9f80444c4e3b493471
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Update the TRACKPAD_INT1_1V8_ODL GPIO configuration so that it acts as a
wakeup source
BUG=b:119598593
BRANCH=octopus
TEST=Ensure that the system wakes up on trackpad events. Ensure that the
suspend_stress_test runs successfully for 25 iterations.
Change-Id: I28292682cf9c8037abb87d265e49a60139550db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/30171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change-Id: I15cfbbab15b940641c3952f2cfb4b11c37574816
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When building coreboot from scratch with 'make -j4', I sometimes see
this error:
CREATE build/mainboard/emulation/qemu-riscv/cbfs-file.wblRgZ.out (from /.../coreboot/.config)
HOSTCC cbfstool/cbfstool (link)
make[1]: execvp: build/util/kconfig/conf: Permission denied
make[1]: *** [/.../coreboot/util/kconfig/Makefile:92: savedefconfig] Error 127
It happens, I think, because the rule generated by
cbfs-files-processor-defconfig runs 'make savedefconfig', which builds
build/util/kconfig/conf, and something also builds it, at the same time.
Fix this case, by making this rule depend on $(objutil)/kconfig/conf.
The same fix is also precautiously applied to the rule for
$(KCONFIG_AUTOHEADER) in Makefile.
Change-Id: Ie93eda567f88ca08c97df7e70cdff5b07442747d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Timothy Pearson