Adds the necessary plumbing for acpi_device_path() to find the LPC
bridge on the AMD Family14 northbridge with an SB800 southbridge.
This is necessary for TPM support since the acpi path to the LPC bridge
(_SB.PCI0.ISAB) doesn't match the built-in default in tpm.c
(_SB.PCI0.LPCB).
Change-Id: I1ba5865d3531d8a4f41399802d58aacdf95fc604
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18402
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
With recent change (a4b11e5c90: soc/intel/skylake: Perform CPU MP Init
before FSP-S Init) to perform CPU MP init before FSP-S init, suspend
resume is currently broken for all skylake/kabylake boards. All the
skylake/kabylake boards store external stage cache in TSEG, which is
relocated post MP-init. Thus, if FSP loading and initialization is
done after MP-init, then ramstage is not able to:
1. Save FSP component in external stage cache during normal boot, and
2. Load FSP component from external stage cache during resume
In order to fix this, ensure that FSP loading happens separately from
FSP initialization. Add fsp_load callback for pre_mp_init which ensures
that the required FSP component is loaded/saved from/to external stage
cache.
BUG=chrome-os-partner:63114
BRANCH=None
TEST=Verified that 100 cycles of suspend/resume worked fine on poppy.
Change-Id: I5b4deaf936a05b9bccf2f30b949674e2ba993488
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18414
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a function to allow FSP component loading separately from silicon
initialization. This enables SoCs that might not have stage cache
available during silicon initialization to load/save components from/to
stage cache before it is relocated or destroyed.
BUG=chrome-os-partner:63114
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae77e20568418c29df9f69bd54aa571e153740c9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18413
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
poppy board uses Maxim 98927 speaker codec and Realtek RT5663
for headset. Select the apropriate NHLT blobs to be packaged in CBFS.
Also, generate the required ACPI NHLT table for codec and the supported
topology in poppy.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=With the required driver support in kernel verify that
the Audio plays on on-board speakers and headset, recording
works from on-board mics and headset mics.
Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18214
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Created using autoport plus some manual work and copying from G505S to
account for the non-H8 EC.
This model uses the same ENE KB9012 EC as the G505S.
Tested:
- Mainboard variant with 8GB Elpida DDR3
- SeaBIOS payload
- Booting into Linux 4.9.6 with Debian/unstable installed on the
internal HDD/SDD slot
- Native raminit
- Both native VGA init and option rom VGA init
- Basic TPM functionality (auto-detection and RNG)
- Battery status readout
- Basic ACPI functions (power button event; power-off; reboot)
- thinkpad-acpi hotkey functions
- thinkpad-acpi LED control (red thinkpad LED)
- Suspend to RAM and resume works
- Mini displayport output works
Known issues:
- Patches needed for EC battery support
https://review.coreboot.org/#/c/18348/https://review.coreboot.org/#/c/18349/
- No thermal zone since temperature sensing is not H8-compatible
and needs to be reverse engineered.
Not tested:
- msata/wwan (probably works)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Change-Id: I52bc4515277e5c18afbb14a80a9ac788049f485c
Reviewed-on: https://review.coreboot.org/18351
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Since we are not using gpio regulators on reef anymore, remove the
selection from Kconfig as well.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18399
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This mainboard uses two i210 Ethernet controller. Therfore we enable the
usage of the i210 driver and have to provide a function to search for a
valid MAC address for all i210 devices by using Siemens hwilib.
Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18380
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Not selecting the Kconfig option `GENERATE_SMBIOS_TABLES` the build
fails with the error below.
```
CC ramstage/ec/lenovo/h8/h8.o
src/ec/lenovo/h8/h8.c:201:2: error: unknown field 'get_smbios_strings' specified in initializer
.get_smbios_strings = h8_smbios_strings,
^
src/ec/lenovo/h8/h8.c:201:2: error: initialization from incompatible pointer type [-Werror]
src/ec/lenovo/h8/h8.c:201:2: error: (near initialization for 'h8_dev_ops.read_resources') [-Werror]
cc1: all warnings being treated as errors
```
So add the appropriate preprocessor guards to fix the build error.
Change-Id: I3baed452d422539a805c628a8c4a6a8c2a809317
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17770
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Using x86 RDRAND instruction, two functions are supplied to
generate a 32bit or 64bit number.
One potential usage is the sealing key generation for SGX.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve to generate a 64bit random number.
Change-Id: I50cbeda4de17ccf2fc5efc1fe04f6b1a31ec268c
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18362
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently the USB OC pins definition only being defined up to OC3.
For PCH-H, OC4 and OC5 are needed, so add both into OC pin enum.
Changes is being verified and booted to Yocto with Saddle Brook.
Change-Id: Idaed6fa7dcddb9c688966e8bc59f656aec2b26eb
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/18364
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Setting both bits 27 and 7 of PCH register PMSYNC_CFG (PMSYNC
Configuration; offset 0x33c8) causes pre-OS display init to fail
on HSW-U/Lynxpoint and BDW-U ChromeOS devices when the VBIOS/GOP
driver is run after the register is set. A re-examination of
Intel's reference code reveals that bit 7 should be set for the
LP PCH, and bit 27 for non-LP, but not both simultaneously.
The previous workaround was to disable the entire power optimizer
section via a Kconfig option, which isn't ideal.
Test: unset bit 27 of PMSYNC_CFG and boot google/lulu,
observe functional pre-OS video output
Change-Id: I446e169d23dd446710a1648f0a9b9599568b80aa
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18385
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
We've been able to narrow down the problem to a single register/
single bit, so revert this commit and address the problem in a
follow-on commit.
This reverts commit 0f2025da0f.
Change-Id: I780f9ea2976dd223aaa3e060aef6e1af8012c346
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18384
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
It explains the prerequisites to run the script, some
background on how to setup the computer running the script,
and the board it gathers the information from.
That information is too long to fit inside the script's
help.
Change-Id: Iecba7310ff1583149c02728e955716775bcbbdc4
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/6660
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Move code common code from each variant's mainboard.asl into
common ACPI code for all variants (like google/auron). This also
adds the _PRW method for the LID0 device for falco and peppy, which
omitted the function when they were originally upstreamed.
See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device
Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18368
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add a test in case we have a DIMM2 not populated but DIMM3 is.
Change-Id: I14f82afe03884740570838e7b2771233356c518d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/18386
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Coverity is detecting 'sp' as a variable which has not been initialized.
This is obviously not correct, so this patch *TRIES* to mark it as false
I'm not positive that this will work because the annotation needs to go
on the line above the error, but this error is inside of a # define.
Does the whole #define count as one line? Can it go on the line
above the #define in the .h file? Does it have to precede every line
where the #define is used? The documentation doesn't make this clear.
Should suppress coverity issues: 1368525 & 1368527
uninit_use: Using uninitialized value sp.
Change-Id: Ibae5e206c4ff47991ea8a11b6b59972b24b71796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18247
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is an enable_s0ix config option in the devicetree that should
be used to disable it when not set:
- do not export C8/C9/C10 C-states in _CST
- do not enable SLP_S0 in FSP
BUG=chrome-os-partner:58666
TEST=test on eve board to ensure that OS only sees 3 ACPI C-states
instead of 6 and that it no longer attempts to enter C10
Change-Id: I90e4dc776d1d17d0b700cda63c8476786cd2e4ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18394
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for more ACPI features in the generic SPI ACPI
driver so it can be flexible enough to support more devices,
or devices in different configurations.
- add a wake pin
- add support for using IRQ GPIO instead of PIRQ
- add power resource support with enable and reset gpios
BUG=chrome-os-partner:61233
TEST=ensure existing SSDT generation is unchanged,
and test that new features generate expected code
Change-Id: Ibe37cc87e488004baa2c08a369f73c86e6cd6dce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18393
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add individual macros for the various interrupt types so
they can be used in devicetree.
BUG=chrome-os-partner:58666
TEST=nothing uses this yet, will be used in an upcoming commit
Change-Id: I2a569f60fcc0815835615656b09670987036b848
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18392
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Move the function that adds a power resource block from
i2c/generic to the acpi device code at src/arch/x86/acpi_device.c
so it can be used by more drivers.
BUG=chrome-os-partner:61233
TEST=verify SSDT table generation is unchanged
Change-Id: I0ffb61a4f46028cbe912e85c0124d9f5200b9c76
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18391
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The hybrid driver select by DRIVERS_LENOVO_HYBRID_GRAPHICS doesn't work
for t400/t500.
Replace it with a custom romstage implementation.
Tested on Lenovo T500 with dual graphics:
* Intel Native GFX init
* AMD VBios
* GNU Linux 4.8.13
* SeaBios as payload
* Discrete is working (44 W)
* Integrated is working (24 W)
* Switchable is working (34 W)
** Both GPUs are enabled, with Intel being connected to the panel
** DRI_PRIME allows to use AMD GPU
** ACPI doesn't seem to work (no vgaswitcheroo)
Depends on Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422
Depends on Change-Id: If389016f3bb0c4c2fd0b826914997a87a9137201
Change-Id: I7496876e9b434d4a2388e1ede27ac604670339b7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18010
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
This company doesn't do custom hardware anymore and doesn't
host the sources anymore. We therefore point to the archived
sources instead.
Change-Id: I5ce4f6a468b852fc1d0947fe2b28a5297f14c437
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/11889
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins)
Prmrr configuration is supported by Kabylake FSP-M with UPD provided.
It is required as one of the SGX initialization steps in BIOS.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified uncore PRMRR MSRs get programmed to set
size and boot.
Change-Id: I2b3dc7c92487505165ee429bd1a37bd60ceac8f3
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It rewrites the results of receive enable stored in the upper nvram
region, to avoid running receive enable again.
Some debug info is also printed about the self-refresh registers.
(Not enforcing a reset here, since 0 does not necessarily mean it's
not in self-refresh).
Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17998
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Previously the raminit failed on hot reset and to work around this
issue it unconditionally did a cold reset.
This has the following issues:
* it's slow;
* when the OS issues a hot reset some disk drives expect their 5V
power supply to remain on, which gets cut off by a cold reset,
causing data corruption.
To fix this some steps in raminit must be ommited on the reset path.
This includes receive enable calibration.
To achieve this it stores receive enable results in RTC nvram for them
to be rewritten on the resume path.
Note: The same thing needs to be done on the S3 resume path.
Calling a hot reset after raminit "outb(0x6, 0cf9)" works.
Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18009
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Maxim 98927 kernel driver requires entries in the ACPI SSDT table,
add a SSDT generator as part of this driver.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=After boot, dump and verify that the generated SSDT ACPI table has the
required entries.
Change-Id: Ic2d4d8449288bc00d085852220b2e1e7a208e9ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://review.coreboot.org/18211
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently there is no distinction between mainboards using
Skylake or Kabylake SoC, Add a config option for Kabylake
SoC to allow mainboards to explicitly select if they are
using it.
Change-Id: Ie7960bd81f88a223894afe3115ddc0bc637e4be4
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18312
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Configure GRUB to build with boot time statistics. That allows users
to add that module to GRUB by adding `boottime` to the list of extra
modules.
Change-Id: I76a07e49aecb37652fe8c7d6a9421fd464424287
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18367
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some simple implementation of the MultiBoot protocol may not pass a
memory map (MULTIBOOT_FLAGS_MMAP missing in the flags) but just the two
values for low and high memory, indicated by the MULTIBOOT_FLAGS_MEMINFO
flag.
Support those kind of boot loaders too, instead of falling back to the
hard-coded values in lib_get_sysinfo().
Tested with a multiboot enhanced version of FILO.
Change-Id: I22cf9e3ec0075aff040390bd177c5cd22d439b81
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18350
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
There are MSRs that are programmable per-core not per-thread, so add
a function to check whether current executing CPU is a primary core
or a "hyperthreaded"/secondary core. For instance when trying to
program Core PRMRR MSRs(per-core) with mp_init, cpu exception is thrown
from the secondary thread. This function was used to avoid that.
Potentially this function can be put to common code or arch/x86 or cpu/x86.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified core PRMRR MSRs get programmed only on primary
thread avoiding exeception.
Change-Id: Ic9648351fadf912164a39206788859baf3e5c173
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18366
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Implement the argc/argv passing as described in coreboot’s payload API:
http://www.coreboot.org/Payload_API
While at it, give the code some love by not needlessly trashing register
values.
Change-Id: Ib830f2c67b631b7216843203cefd55d9bb780d83
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Simplify the code by directly using the arguments on the stack as base
pointer relative memory references, instead of loading them into
intermediate registers first.
Make it more robust by preserving all callee saved registers mandated by
the C calling convention (and only those), namely EBP, EBX, ESI and EDI.
Don't assume anything about the register state when the called function
returns -- beside the segment registers and the stack pointer to be
still the same as before the call.
Change-Id: I383d6ccefc5b3d5cca37a1c9b638c231bbc48aa8
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18335
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
According to coreboot’s payload API [1], the called payload should be
able to return a value via %eax. Support this by changing the prototype
of start_main() and pass on the return value of main() to the caller
instead of discarding it.
[1] https://www.coreboot.org/Payload_API
Change-Id: I8442faea19cc8e04487092f8e61aa4e5cba3ba76
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18334
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to coreboot’s payload API [1] the argc value should be passed
at stack offset 0x10, so we need to push a dummy value to comply to the
API.
[1] https://www.coreboot.org/Payload_API
Change-Id: Id20424185a5bf7e4d94de1886a2cece3f3968371
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18333
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for generating digitizer node in SSDT using wacom i2c
driver.
BUG=None
BRANCH=None
TEST=Verified that the node shows up in SSDT.
Change-Id: If7e1e2463778c2ff7263eff995def149457edcde
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18373
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tobias Diedrich