OCP platform Tiogapass is a 2-socket server platform, which
is based on a chipset including Intel Skylake-SP processors
and a Lewisburg PCH. Skylake-SP is a processor in Intel Xeon
Scalable Processor family.
Following ACPI tables are added:
DSDT/SSDT, MADT, FACP, FACS, HPET, MCFG, SLIT, SRAT, DMAR
This patchset is tested on a Tiogapass board. It booted with
Linux kernel 4.16.0; lscpu command shows all 72 cpus (2 sockets,
18 cores, 2 thread per core); ssh command shows
networking is up from Mellanox ConnectX-4 PCIe NIC card.
Towards successful gerrit buildbot build, note that:
* microcode is in coreboot intel-microcode submodule repo.
* IFD binary is included in this patch.
* Dummy ME binary is used, as it may take long time for Intel
ME binary to be available in public domain.
* Fake FSP binary is used, as at this moment the SKX-SP
FSP binary is not going to be available in public domain.
Known issues (Not intend to address in this initial support for
Xeon-SP processors):
* c6 state is not supported.
* dsdt table is not fully populated, such as processor/socket
devices, some PCIe devices.
* SMM handlers are not added.
Following are some command execution with CentOS booted from
local SATA disk:
[root@localhost ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 72
On-line CPU(s) list: 0-71
Thread(s) per core: 2
Core(s) per socket: 18
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6139 CPU @ 2.30GHz
Stepping: 4
CPU MHz: 140.415
BogoMIPS: 4626.46
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-17,36-53
NUMA node1 CPU(s): 18-35,54-71
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.23.68.190 netmask 255.255.0.0 broadcast 172.23.255.255
inet6 2620:10d:c082:9063:268a:7ff:fe57:5af0 prefixlen 64 //cut
inet6 fe80::268a:7ff:fe57:5af0 prefixlen 64 scopeid 0x20<link>
inet6 2620:10d:c082:9063::5d2 prefixlen 128 scopeid 0x0<global>
ether 24:8a:07:57:5a:f0 txqueuelen 1000 (Ethernet)
RX packets 84249 bytes 6371591 (6.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8418 bytes 748781 (731.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 613 bytes 63906 (62.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 613 bytes 63906 (62.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@localhost ~]# cbmem
36 entries total:
// Lines were cut to avoid checkpatch.pl warnings
Total Time: 96,243,882,140,175,829
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I29868f03037d1887b90dfb19d15aee83c456edce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This time, it failed to build if measured boot was not enabled. Fix this
problem, and make sure flashconsole will not break like that again.
Change-Id: I5f5ffd14a3225804524cb0c1518e3d99737e0a93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This update is a combination of all four of the patches so that the
commit can be done without breaking parts of coreboot. This possible
breakage is because of the cross-dependencies between the original
separate patches would cause failure because of data structure changes.
security/intel/stm
This directory contains the functions that check and move the STM to the
MSEG, create its page tables, and create the BIOS resource list.
The STM page tables is a six page region located in the MSEG and are
pointed to by the CR3 Offset field in the MSEG header. The initial
page tables will identity map all memory between 0-4G. The STM starts
in IA32e mode, which requires page tables to exist at startup.
The BIOS resource list defines the resources that the SMI Handler is
allowed to access. This includes the SMM memory area where the SMI
handler resides and other resources such as I/O devices. The STM uses
the BIOS resource list to restrict the SMI handler's accesses.
The BIOS resource list is currently located in the same area as the
SMI handler. This location is shown in the comment section before
smm_load_module in smm_module_loader.c
Note: The files within security/intel/stm come directly from their
Tianocore counterparts. Unnecessary code has been removed and the
remaining code has been converted to meet coreboot coding requirements.
For more information see:
SMI Transfer Monitor (STM) User Guide, Intel Corp.,
August 2015, Rev 1.0, can be found at firmware.intel.com
include/cpu/x86:
Addtions to include/cpu/x86 for STM support.
cpu/x86:
STM Set up - The STM needs to be loaded into the MSEG during BIOS
initialization and the SMM Monitor Control MSR be set to indicate
that an STM is in the system.
cpu/x86/smm:
SMI module loader modifications needed to set up the
SMM descriptors used by the STM during its initialization
Change-Id: If4adcd92c341162630ce1ec357ffcf8a135785ec
Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: ron minnich <rminnich@gmail.com>
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- Channel 0: 8-GB on-board DDR4 Samsung K4AAG165WA-BCTD
- Channel 1: 8-GB/16-GB/32-GB DDR4 SO-DIMM
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
If stage cache is enabled, we should not allow S3 resume
to load firmware from non-volatile memory.
This also adds board reset for failing to load postcar
from stage cache.
Change-Id: Ib6cc7ad0fe9dcdf05b814d324b680968a2870f23
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a BOARD_GOOGLE_KEVIN variant config that enables
CONFIG_VBOOT_MOCK_SECDATA. This is to ensure that Jenkins will build the
MOCK_SECDATA-specific code at least once, to be sure we don't
accidentally break it during refactoring.
Change-Id: Ib0ffaccdf4601d6bfb889ae289d1d7df18bed1fd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37773
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This config is a slightly stripped configuration of the Chromium OS
configuration used in production. Apparently the bootblock fills up
faster than usual on this device, resulting in address overflows.
Add this config here so we'll notice early in the future.
Change-Id: I3145bba63d32ddb9d00fd98d3cb774bf9ddd69a6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36923
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable vendorcode measured and verified boot.
Use VBOOT test key for VENDORCODE_ELTAN_VBOOT_KEY_FILE
BUG=N/A
TEST=booting Embedded Linux 4.20 kernel on Facebook FBG1701
Change-Id: Ia2cb3bb873b2d5e7e9031e5b249d86605d8e0945
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It would be useful if we have at least one "new" board on which we
actually built vboot, in order to notice if something breaks.
Change-Id: I16c7867e3f0f4e1f2e6ae3918c30789e39881b85
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Enable VBOOT support on all devices that have a 8 MiB flash, using a
single RW_MAIN_A partition, allowing the use of tianocore payload in
both RW_MAIN_A and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT and regular boot
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_A by default
Also build test VBOOT on Lenovo T420.
Tested on Lenovo T520 using Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6.
Change-Id: Icb7b263ed86551cc53e1db7babccaca6b3ae2fe6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This board is EOL and has FSP2.0 support, so drop the older
version.
Change-Id: If5297e87c7a7422e1a129a2d8687fc86a5015a77
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Also add a test case for that, a config taken from chromiumos with some
references to binaries dropped that aren't in our blobs repo (eg audio
firmware).
Change-Id: I411c0bacefd9345326f26db4909921dddba28237
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29223
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To avoid mangled characters on serial output from iPXE we have to disable
serial from iPXE console. More to that to have correct serial input we
have to enable SeaBIOS SERCON option with default configuration.
The only limitation of this configs is that apu5 doesn't detect iPXE -
that platform is not for public use so it doesn't affect anyone.
Change-Id: I124705bd691b3c8dcd9a2636b17c019d02732c5a
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Rename `FRAMEBUFFER_KEEP_VESA_MODE` to `LINEAR_FRAMEBUFFER` and put
it together with new `VGA_TEXT_FRAMEBUFFER` into a choice. There are
two versions of `LINEAR_FRAMEBUFFER` that differ only in the prompt
and help text (one for `HAVE_VBE_LINEAR_FRAMEBUFFER` and one for
`HAVE_LINEAR_FRAMEBUFFER`). Due to `kconfig_lint` we have to model
that with additional symbols.
Change-Id: I9144351491a14d9bb5e650c14933b646bc83fab0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Removes the pre-defined VGA bios file and id because
the build system includes every vgabios.
Also make the VGA output primary by default
Change-Id: I87d52ef2d1e151c6e54beba64316fe9043668158
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/18181
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The coreboot builder makes use of the pre defined configuration
files by executing abuild with -d option. These configuration
files contain a basic configuration.
Change-Id: I41470fe7aaa0fdae545ad9d702326a202d0d2312
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/18161
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Test some config options that don't typically get tested.
Change-Id: Ie05c99411c8ce6462a6f5502b086ee2b72a4324b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17591
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Michał Żygowski