Add minimal Makefile based on cbmem’s Makefile.
The make target `junit.xml` is removed as this is handled differently
since commit de9adebb (Add junit.xml code to top Makefile.inc instead of
utils).
Also the `junit.xml` is removed in the make target `clean`.
Additionally, the make target `distclean` is added, as the current
junit.xml code in the top `Makefile.inc` requires that.
Change-Id: I164b1f7733505bca6248d0711d7ad71d635fa926
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11876
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Auron only has three GPIOs for RAMID, so there is no need for
sixteen SPD file entries. Only include 8 SPD entries.
Change-Id: Icf83719a2a5b9271b29f48cde5c66c4c8ccd07f4
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12073
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On Broadwell, this reduces the number of 'remarks' in the IASL build
from 222 to 3.
Fixes these remarks:
Object is not referenced (Name is within method [_CRS])
The ACPI compiler is trying to be helpful in letting us know
that we're not using various fields in the MCRS ResourceTemplate
when we define it inside of the _CRS method. Since we're not
intending to use those objects in the method, it shouldn't be an
issue, but the warning is annoying and can mask real issues.
Moving the creation of the MCRS object to outside of the CRS
method and referencing it from there solves this problem.
This change was made for fsp_baytrail in commit 2eaa0d49
fsp_baytrail: Fix ACPI 'Object is not referenced' warnings
Change-Id: I67a1faf963d1868f4133c7747a43a511cd28a44b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ifb434db1b8eb01acf48f26366c5237ae49a8730a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ide50b34184b80c86b996f86dd589c3cf3bf75587
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: I1e69cf0fd73e70ed6656b9ed6f55aba4c56a6edd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11882
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Before this fix the value of PcdEnableSdio was printed as the MIPI/ISP
configuration option.
TEST=Built and booted on Minnowboard Max
Change-Id: Ia9b02d520f4e615f90b45935456b9d97c5d00f11
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: http://review.coreboot.org/10126
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
connections checked by desoldering the FCH and looking at the PCB
this lowers the power consumption by about 150-200mW measured on primary side
based on change #5397
Change-Id: I986c4cc73a247994f2a47fdfd03f585069ca9385
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/11866
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch fixes compilation of cbfstool on Cygwin.
As reported in http://review.coreboot.org/#/c/10027
cbfstool on Cygwin likes to be compiled with -D_GNU_SOURCE.
That patch was abandoned because it would unwantedly turn on
more GNU extensions. Instead of doing that, only enable the
define on Cygwin, switch to -std=gnu99 instead of -std=c99 to
make fileno and strdup actually available.
A MINGW32 check that was forgotten in Makefile was copied over
from Makefile.inc to keep the two files in sync.
This patch has no impact on non-Windows builds.
Change-Id: I068b181d67daf9c7280110e64aefb634aa20c69b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11667
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
don't use non-volatile pointers for MMIO access
Change-Id: I9f38012a806e43f2535265f1d25537c59b53904e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12081
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The reintroduction of cougar_canyon2 crossed beams with the
moving the GMA display brightness data in ACPI into individual
mainboards.
Make things build again by having the board use the same default values
that it used to use automatically. They may be wrong, but no worse than
what was there before.
Change-Id: Id788034c38b42e1c35d9cd17e9bbb2ce49e3e91c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12132
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This utility should make it easier to complete and maintain
the database of coreboot subsystem maintainers (MAINTAINERS
file)
This will need a bit of tender love and care to print information
in an easily machine readable output for the build system, but its
a first start to query the maintainers database.
Build with:
$ go build util/scripts/maintainers.go
Find a maintainer for a set of files with:
$ ./maintainers Makefile Makefile.inc
Makefile is in subsystem BUILD SYSTEM
Maintainers: [Patrick Georgi <patrick@georgi-clan.de>]
Makefile.inc is in subsystem BUILD SYSTEM
Maintainers: [Patrick Georgi <patrick@georgi-clan.de>]
Check the maintainer database with:
$ ./maintainers
.gitignore has no subsystem defined in MAINTAINERS
.gitmodules has no subsystem defined in MAINTAINERS
.gitreview has no subsystem defined in MAINTAINERS
3rdparty/arm-trusted-firmware has no subsystem defined in MAINTAINERS
3rdparty/blobs has no subsystem defined in MAINTAINERS
3rdparty/vboot has no subsystem defined in MAINTAINERS
COPYING has no subsystem defined in MAINTAINERS
Documentation/AMD-S3.txt has no subsystem defined in MAINTAINERS
Documentation/CorebootBuildingGuide.tex has no subsystem defined in MAINTAINERS
Documentation/Doxyfile.coreboot has no subsystem defined in MAINTAINERS
[..]
Change-Id: I49c43911971152b0e4d626ccdeb33c088e362695
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12119
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Cygwin complains:
cbfstool.c: 1075:5 error: array subscript has type 'char' [-Werror=char-subscripts]
so add an explicit cast.
Change-Id: Ie89153518d6af2bacce3f48fc7952fee17a688dd
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11666
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To help hypervisors to assign PCI devices individually to virtualization
guests, page align dynamically allocated MMIO resources.
Tested with kontron/ktqm77 which has dynamically configured onboard
devices on the root bus and secondary buses. Booted Linux and checked
the configuration with `lspci -v`. Got the configuration through Muen's
tools which are very picky about overlapping and alignment. Booted a
Muen based system that uses many onboard devices. GMA, xHCI and one NIC
(on a secondary bus) were verified to function properly.
Change-Id: I2b7115070e1ccad64565feff025289732c3b5e66
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12111
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Those are actually board specific. Keep the old value as defaults,
though. The defaults are included by all affected boards.
Change-Id: Ib865c7b4274f2ea3181a89fc52701b740f9bab7d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11705
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Values based on correlation of brand strings, brand numbers and the TDP
listings on AMD's web site (Wikipedia for Athlon 64 FX-7x TDPs).
Change-Id: I7e6d12d0b6cc4fefc3f84076234c62c40e08304c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10926
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the documentation further up in the file:
F: drivers/net/ all files in and below drivers/net
F: drivers/net/* all files in drivers/net, but not below
F: */net/* all files in "any top level directory"/net
Add trailing slashes to directory names.
Change-Id: I7bfd2eb2528a75fb6af79a990acb89f5e4251383
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12118
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
It works there, we want it, disable that restriction.
Change-Id: Idc023775f0750c980c989bff10486550e4ad1374
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/12094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit e660651824.
After some discussion on IRC we decided to revert it as libpayload can
only read the copy that was removed (and other users like nvramtool can
only read the other copy). So we need both copies at this time.
Signed-off-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6cf6b2a1523d771bb52f3d5720b1b16ed4b348db
Reviewed-on: http://review.coreboot.org/11696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We need to special-case filling out the vboot structures when
we use CBFS instead of vboot's custom indexed format, otherwise
(due to the way the CBFS header looks), it will try to write several
million entries.
Change-Id: Ie1289d4a19060bac48089ff70e5cfc04a2de373f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/11914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This way, commit differences will be easier to read. Also sort the list
lexicographically.
Change-Id: I4ce3ac9018a3fddf5e30d7c1ac0c57090fac1d3d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/12084
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Some registers only allow word-sized or half-word-sized operations and will
cause a data fault when accessed with byte-sized operations.
However, the compiler may or may not break such an operation into smaller
(byte-sized) chunks. Thus, we need to reliably perform word-sized operations for
32 bit read/write and half-word-sized operations for 16 bit read/write.
This is particularly the case on the rk3288 SRAM registers, where the watchdog
tombstone is stored. Moving to GCC 5.2.0 introduced a change of strategy in the
compiler, where a 32 bit read would be broken into byte-sized chunks, which
caused a data fault when accessing the watchdog tombstone register.
The definitions for byte-sized memory operations are also adapted to stay
consistent with the rest.
Change-Id: I1fb3fc139e0a813acf9d70f14386a9603c9f9ede
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: http://review.coreboot.org/11698
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Currently, cbfstool regressed that removing a file from CBFS the space
is marked as empty but the filename is still shown, preventing adding a
file with the same name again. [1]
```
$ echo a > a
$ echo b > b
$ ./util/cbfstool/cbfstool test.rom create -m x86 -s 1024
Created CBFS (capacity = 920 bytes)
$ ./util/cbfstool/cbfstool test.rom add -f a -n a -t raw
$ ./util/cbfstool/cbfstool test.rom add -f b -n b -t raw
$ cp test.rom test.rom.original
$ ./util/cbfstool/cbfstool test.rom remove -n
$ diff -up <(hexdump -C test.rom.original) <(hexdump -C test.rom)
--- /dev/fd/63 2015-08-07 08:43:42.118430961 -0500
+++ /dev/fd/62 2015-08-07 08:43:42.114430961 -0500
@@ -1,4 +1,4 @@
-00000000 4c 41 52 43 48 49 56 45 00 00 00 02 00 00 00 50 |LARCHIVE.......P|
+00000000 4c 41 52 43 48 49 56 45 00 00 00 02 ff ff ff ff |LARCHIVE........|
00000010 00 00 00 00 00 00 00 28 61 00 00 00 00 00 00 00 |.......(a.......|
00000020 00 00 00 00 00 00 00 00 61 0a ff ff ff ff ff ff |........a.......|
00000030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
$ ./util/cbfstool/cbfstool test.rom add -f c -n c -t raw
$ ./util/cbfstool/cbfstool test.rom print
test.rom: 1 kB, bootblocksize 0, romsize 1024, offset 0x0
alignment: 64 bytes, architecture: x86
Name Offset Type Size
c 0x0 raw 2
b 0x40 raw 2
(empty) 0x80 null 792
```
So it is “deteled” as the type changed. But the name was not changed to
match the *(empty)* heuristic.
So also adapt the name when removing a file by writing a null byte to
the beginning of the name, so that the heuristic works. (Though remove
doesn't really clear contents.)
```
$ ./util/cbfstool/cbfstool test.rom remove -n c
$ ./util/cbfstool/cbfstool test.rom print
test.rom: 1 kB, bootblocksize 0, romsize 1024, offset 0x0
alignment: 64 bytes, architecture: x86
Name Offset Type Size
(empty) 0x0 null 2
b 0x40 raw 2
(empty) 0x80 null 792
```
[1] http://www.coreboot.org/pipermail/coreboot/2015-August/080201.html
Change-Id: I033456ab10e3e1b402ac2374f3a887cefd3e5abf
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11632
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Behave as nvramcui.
Avoid a "General Protection Fault Exception" when launched by SeaBIOS on
pcengines APU1.
Change-Id: I00b1f859f76e693e8d49a38c1e02f4f49add85b7
Signed-off-by: Maxime de Roucy <maxime.deroucy@gmail.com>
Reviewed-on: http://review.coreboot.org/11731
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
TinyCursess is officially spelled in CamelCase [1].
[1] https://github.com/tommyettinger/TinyCurses
Change-Id: I7e0aa5af54140796a981c0f4c58950b25fdd67ba
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11727
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of adding code to generate the junit.xml file for jenkins to
each of the util makefiles, add it once to the top level Makefile.inc.
Create a list of tools to run the test on.
Add nvramtool and inteltool to the list of utilities tested.
Note that the util builds depend on implicit rules, so MFLAGS and
MAKEFLAGS have to be cleared to get the builds to work.
Change-Id: Id7ee5ea41ce3bf4a40fb50942ae785bb838fa639
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11910
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With the introduction of these options in commit b26156e
(bd82x6x/xhci: Set mask of ports switchable between USB2 and USB3.)
the default regressed to disable these capabilities. Maybe other boards
regressed too. I didn't check.
Change-Id: I220896e656d00145618e61d55b74904517c7d855
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11287
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This will run the lint-stable scripts on jenkins to block a commit with
obvious and known errors.
It runs in under a second on my system, so shouldn't contribute to any
real delay on jenkins.
Change-Id: I6ff3468ec29dc4ccd0c115f2c26e26b291c507df
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11892
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When the script was pulled out of the makefile, it was left as it was
written in the makefile to show the continuity with the original. This
patch cleans up issues identified by shellcheck and adds comments.
Change-Id: I5e6573a4fdfbb397e15db38e2e3dfadeb3430573
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11931
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
To add lint to jenkins testing, we need junit.xml output. This adds an
optional --junit command line parameter to enable output to an xml file
in the lint directory.
Change-Id: I5588190cb050b9dbe99458cb18a71a147769f50e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11891
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Paul Menzel