In skylake based platforms, setting GPIO pad reset config
to DEEP will reset the gpio configuration across warm reset,
set it to RSMRST to preserve the configuration across warm resets.
Also, moving the configuration from early to late as appropriate.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I38940b7c7d71e60bf0e51d6978a00be148ad61bc
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adapted from Chromium commit 12ad5b5: Reks : override USB2 Phy settings...
Base on Intel recommendation, override following
settings for USB2 port 1/2/3 on BSW D-stepping SOC.
1. Set USB[1] register for right side to 7321
2. Set USB[2] register for left side to 7021
3. Set USB[3] register for CCD to 7021
Original-Change-Id: I04240a010e875f29c47f4fea83ff918f180b0273
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iabd6312576e9897315c4e4dbf19341380d9d1414
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit 6ee6f3d: Reks: To set the RX ODT limit...
Override RX ODT and DRAM geometry for Micron part MT52L256M32D1PF-107.
Use get_ramid() to determine if override is necessary.
Original-Change-Id: I41f3aba030a00152e1217533ef953338ac396605
Original-Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Original-Reviewed-by: Kane Chen <kane.chen@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iea8c3c67e5afb21285dc15ad665474ad5f192423
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Once coreboot is ready and payload has been loaded a bit inside the NC
FPGA needs to be set to notify this event. As there are NC FPGAs with
different PCI device IDs save the BAR0 address in a global variable once
the driver evaluates this address. It can then be used to access the
register from the boot state machine callback without the need of searching
for all possible PCI devices again.
As this driver is only used at ramstage there is no need of using
CAR_GLOBAL for the global variable. Use a Kconfig switch to make this
feature selectable from mainboard as not every mainboard may have a FPGA
with that capability.
Change-Id: I9cd09e7051edde30d144a7e020b84bb549e9e8b9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/22138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Collect all known codenames for thinkpads.
Change-Id: Iae44ceb29675511ec562c275e750087eca5d2f27
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Sebastian "Swift Geek" Grzywna <swiftgeek@gmail.com>
Reviewed-on: https://review.coreboot.org/21364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
`NULL` already has that type in coreboot.
```
src/include/stddef.h:#define NULL ((void *)0)
```
Change-Id: I73aeaef178be8779020c436732952aa732e90c46
Reported-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/22296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The southbridge bootblock entry point bootblock_southbridge_init()
just calls i82371eb_enable_rom() which does all the work. Move all
that code into bootblock_southbridge_init() and drop the second
function.
Plus combine the 3 lines that set 3 bits in XBCS into one.
Change-Id: I07a5a28c91da9586e3bdaaf4521cba3f53a5cc01
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
ASL+ Optimizing Compiler/Disassembler version 20170831 shows the remark
below.
```
dsdt.aml 87: Method (_CRS, 0x0, NotSerialized)
Remark 2120 - ^ Control Method should be made Serialized \
(due to creation of named objects within)
```
So, serialize the method.
Fixes: commit 4a51ea8470 (google/kahlee: Add ASL for Elan touchpad)
Change-Id: I664f493318cbfd80d91565c0d29ec918278c4906
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Use the correct conversion specifier for `size_t` to fix the error
below.
```
from src/soc/intel/quark/spi.c:18:
src/soc/intel/quark/spi.c: In function 'xfer':
src/soc/intel/quark/spi.c:107:20: error: format '%ld' expects argument \
of type 'long int', but argument 3 has type 'unsigned int' \
[-Werror=format=]
printk(BIOS_ERR, "bytesin > %ld\n", sizeof(ctrlr->data));
^
```
Found-by: gcc (Debian 7.2.0-8) 7.2.0
Change-Id: I3974d116e85715086a2bd5533a80a20c4cc43303
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/22130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Clang Static Analyzer warns about an unused assignment, when
building the image for the Lenovo X60.
```
src/arch/x86/gdt.c:39:6: warning: Value stored to 'num_gdt_bytes' \
during its initialization is never read
u16 num_gdt_bytes = (uintptr_t)&gdt_end - (uintptr_t)&gdt;
^~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
```
If `CONFIG_RELOCATABLE_RAMSTAGE` is selected, the function returns
before the assignment is used. So, move the assignment below the if
statement.
Change-Id: Ibcb8bce743d8cb3625647804816fb97f937dc429
Found-by: clang version 4.0.1-6 (tags/RELEASE_401/final), Debian Sid/unstable
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Move files that are particularly specific to the mainboard into the
variant directory. Files that only have small areas of mainboard
specific pieces use #if to separate between the boards.
Add memory.c to split out the variant board id into a weak function.
Add baseboard/gpio.h to satisfy the build - this will be updated in the
next commit.
BUG=b:68293392
Change-Id: I7c1beb45f571f2547f3b5b0d7ec78923d0cec761
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix the warning below by making the integer literal unsigned.
```
CC bootblock/soc/intel/common/block/*/lpc_lib.o
src/soc/intel/common/block/lpc/lpc_lib.c:91:17: warning: The result of the \
'<<' expression is undefined
alignment = 1 << (log2_ceil(window_size));
~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
```
Found-by: Clang static analyzer scan-build
(clang version 4.0.1-6 (tags/RELEASE_401/final))
Fixes: e237f8b7 (soc/apollolake/lpc: Open I/O to LPC based on resource allocation)
Change-Id: I094fb469f020f3c1fae936e304b4458858842a8e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/22198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Fix the warning below.
```
CC bootblock/lib/reg_script.o
src/lib/reg_script.c:375:11: warning: Value stored to 'value' during its \
initialization is never read
uint64_t value = msr.hi;
^~~~~ ~~~~~~
```
Found-by: Clang static analyzer scan-build
(clang version 4.0.1-6 (tags/RELEASE_401/final))
Fixes: fd461e39 (regscript: Add support for MSR type)
Change-Id: I218e45d12f2f00e2ad4cfe5410029f407b57568d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/22197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Make the format of two multi-line comments compliant with the coding
style.
Change-Id: I8bc7b1eb175957b76ca19acdcb29b06ae86429b4
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/22279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add Apollo Lake CPU device ID for E0 stepping.
Change-Id: I28fa222cd28b783d22c347cdbbd769e66bf10c30
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The default setting for I2Cx is 400kHz. On this mainboard there is a
device on I2C0 which requires a lower clock rate to work correctly. For
this reason we set the frequency to 100kHz.
Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard has its own coreboot ready LED. The LED is switched on
via GPIO CNV_RGI_DT.
Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are PCI devices, which are connected to the PCIe
root port via a PCIe-2-PCI bridge. One of the devices only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 4 (Device 14.0).
The following routing is required:
INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA#
Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
If the Running Average Power Limits (RAPL) feature is disabled, the CPU
should be set to the Max Non-Turbo Ratio. RAPL is switched off by
CONFIG_APL_SKIP_SET_POWER_LIMITS. Furthermore, a frequency change should
be prevented by disabling Enhanced Intel Speedstep Technology (EIST). So
the CPU should run with constant frequency with this setting.
Change-Id: I67020f7e75700255629294fd9bcf67ee01765a01
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Current VBT setting for T8 is only 1ms which is under Innolux N116BCA-EA1
panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
CQ-DEPEND=CL:*493633
Change-Id: I7934b0f6d40b15796c55d360995c5eb0c5049222
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/22294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The x86 bsf and bsr instructions only allow for a memory
or register operand. The 'g' constraint includes immediate
operands which the compiler could choose to emit for the instruction.
However, the assembler will rightfully complain because the
instruction with an immediate operand is illegal. Fix the constraints
to bsf and bsr to only include memory or registers.
Change-Id: Idea7ae7df451eb69dd30208ebad7146ca01f6cba
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22291
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Delete the LPC I/O decode configuration from fixme.c. This code is
superseded by early_setup.c.
Change-Id: I86ac5e997c98fea853659bc66b13128f0872f571
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add #defines that will allow easy use of PCI devices across stages.
Future work can convert soc/amd/stoneyridge to use these and clean
up the DEV_D18F4 macro still in place.
Change-Id: I78c297d9610009e7b9e2233984e1a167f0ab88c7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add #define values for the first MMIO base/limit, the first I/O
base/limit, and VGA enable registers.
Change-Id: I2c209224d356cf3f83a0ddb37974831611a89760
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add #define values for the HPET device. In Stoney Ridge, the base
address is fixed and cannot be relocated.
Change-Id: Id36fd9ecc90d54a92144f2cca7cec6d84abfdabd
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Leaving the wifi related gpios unmodified for now
due to FSP problem. If H0-H3 is configured as native mode
and GPIORXDIS, GPIOTXDIS bits in DW0 are cleared, it causes
FSP to assert when wifi module is attached. coreboot gpio
macros clears these 2 bits because they are suppose to be
"don't care" in native mode.
TEST=Boot to OS and verify wifi
Change-Id: Ica5e1c43802d04a9471cdfa0087e86f669122fff
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When Cr50 TPM is being reset, it continues replying to the SPI bus
requests, sends wrong register values in response to read requests.
This patch makes sure that the TPM driver does not proceed unless
proper value is read from the TPM device identification register.
If the read value is still wrong after 10 retries taken with 10 ms
intervals, the driver gives up and declares TPM broken/unavailable.
BRANCH=cr50
BUG=b:68012381
TEST=ran a script resetting the Fizz device as soon as the "index
0x1007 return code 0" string shows up in the AP console output.
The script keeps rebooting the Fizz indefinitely, before this
script Fizz would fail to read TPM properly and fall into
recovery after no more than four reboots.
Change-Id: I7e67ec62c2bf31077b9ae558e09214d07eccf96b
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/22231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch uses common SCS library to set up sd card.
Change-Id: I7978bebaeba3a04fbfd01b3a5e5a37af61d2f4ce
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/21604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a function to program a customized LED setting
for Realtek 81xx family. It reads the settings from devicetree under
target board and programs the setting to offset 0x18 and 0x19.
BUG=b:65437780
TEST=Add customized_leds register in devicetree.cb under target board,
enable RT8168_SET_LED_MODE flag. Make sure the setting is
programmed correctly to offset 0x18 and 0x19. Observed the
LEDs were behaving as expected. Executed suspend/resume and
the LEDs were still working as expected.
Change-Id: Ib3d4f2cd98ac391e1661a891d604bdd1974d07f6
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is to enable SPD word access to reduce boot time. It can save
80 ~ 100 ms per DIMM.
BUG=b:67021853
BRANCH=None
TEST=system boot, and boot time is reduced
Change-Id: Ic527a539ed634e15b939b18fff4b4e08ebb3ec57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For Raydium, export reset GPIO as well as PowerResource.
Let EN_PP3300_TOUCHSCREEN signal will goes to low at S3 mode.
BUG=b:67879912
BRANCH=coral
TEST=emerge-coral coreboot
Change-Id: Ibf501b40ecfc957fd8be7ebffd2357dfa0e07757
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/22252
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change increases the spd read performance by using smbus word
access.
BUG=b:67021853
TEST=boot to os and find 80~100 ms boot time improvement on one dimm
Change-Id: I98fe67642d8ccd428bccbca7f6390331d6055d14
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Divya Chellap