Running the x86_64 qemu mainboard target with '-accel kvm' results in hang,
as the 'D' and 'A' bits needs to be set in read only page tables.
Tested on QEMU Q35: Boots into payload with '-accel kvm'.
Change-Id: I4beae8deec6bf34f9762e7b54c5da4e5b63f6d24
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36778
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Location of _start16bit in entry16.inc is about to see some changes,
lets make sure they don't break the alignment requirement here.
Change-Id: Id8a0964982387e5321e8c89254922e1242cf85ee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Switching was done by moving a SIO configuration and
the clocks setup from 'romstage.c' to 'bootblock.c',
following the example of change CB:37719 (fc749b2).
TEST=Boots into Artix Linux 2019 without a problem.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I780fa87cb9cb3c45844c388331ef89eb8eb70ebb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The same default values are used if the values are not present in devicetree.
Change-Id: Ic910cdc8077e1b3e98eadc77a2d1fa0f9cb38e5b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner
If the board doesn't provide VRconfig in devicetree make sure to use
the lookup table for IccMax instead of defaults for some mobile SoC.
Also use decimal values instead of hex.
Change-Id: If31063f9b483a3bbd6cc90df1c1b76b4efc66445
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37598
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_H3 gpio config for easier review. This
toggles the MAX amp which not all boards have. Move the pin
configuration to boards with the respective devicetree configuration
following on from the theme of commit b417786525.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: Iefd2223af79a13c8a42d07bc10b2772dbff6d3e5
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_C15 group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I578245e24895d361d80ad016a4f18204e2b6e1ca
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The baseboard GPIO table definitions are too straineous to the extend
that variants need to redefine assumptions back to NC. Invert this so
that baseboard by default assumes the safer NC and move the specific
board configurations to their respective places.
This patch handles the GPP_A* group for easier review.
BUG=b:142094759
BRANCH=none
TEST=builds
Change-Id: I29b4323ac80b1288b2562846217c4f377714fc2c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To be safe for now, don't differentiate between SKUs and use lower
values to ensure board won't be browned out.
BUG=b:143246320
TEST=none
BRANCH=none
Change-Id: I041ebaa33bf2582386198290e625099ba8e2f3c9
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37651
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows the values to be set in a .config
BUG=none
TEST=Was able to set the value from a .config and built careena firmware
Change-Id: I757e4b9a0b80ff42c1f49143a44f15550366fd0b
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37879
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Generally work towards a more loose baseboard definition by moving out
some original assumptions to be board specifics. Specifically Puff does
not have the MAX98357A speaker amp and enabling the driver winds up
generating incorrect SSDT tables that confuse the kernel. Since
devicetree inherits the chip from device node in base and an override
will also inherit the chip and thus dispatch the unwanted fill_ssdt fn
call.
V.2: lean on linker to drop max98357a driver when not in dt.
BRANCH=none
BUG=b:146519004
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I8e7fed69a4c6d9610ac100da6bae147828ebfa81
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37909
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Two things here:
i. ) FSP requires that function 0 be enabled whenever any non-zero
functions hang under the same bus:device.
ii.) FSP reorders function 6 RP to be function 0 if function 0 is
indeed unused.
BUG=b:146437819
BRANCH=none
TEST=none
Change-Id: I0f499a23495e18cfcc712c7c96024433a6181a4c
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* Make use of introduced SSDT config mode access
* Make use of introduced SSDT mutex
* Provide ACPI functions to safely access SIO config space
* Implement method to query LDN enable state
* Implement method to set LDN enable state
* Use introduced functions to implement _DIS and _STA in the device
* Update documentation
Tested on Aspeed AST2500 and Linux 5.2.
Manually verified ACPI code that generates no errors in Linux.
Change-Id: I520b29de925f368cd71ff8f1f58d2d57d72eff8d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add functions to write ACPI SSDT code for entering and leaving
the config mode.
To be used by ACPI generators.
Tested on Linux 5.2 using the Aspeed SSDT generator.
Change-Id: I14b55b885f1c384536bafafed39ad399639868e4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
It provides no useful information, so it might as well vanish.
Change-Id: I0df6f4639a16058486c2e2d40fe4067d65670731
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
As discussed in CB:35077, since both measured boot and verified boot
depends on vboot library, it had better to introduce a dedicated flag
CONFIG_VBOOT_LIB to control the building and linking of the vboot
library, and make other flags needing vboot library select it. Only
the actual verification stuff should be conditional on CONFIG_VBOOT.
Change-Id: Ia1907a11c851ee45a70582e02bdbe08fb18cc6a4
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Tigerlake and Jasperlake fsp requires stack size to be minimum 192 KiB
and heap size to be minimum 128 KiB.
Updating both Kconfig to meet size requirements.
Also updated required CAR region size during boot block due to increment
in stack & heap requirement by fsp
Change-Id: I38e93b5986811ff3e0a8df5f4f36af35f308cb6b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37764
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The delay cell result should use DDR clock PLL rate for computation,
and should not be divided by 2.
This helps to improve DRAM stability.
BUG=b:80501386,b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: Idf5cce206e248bb327f9a7d27c4f364ef1c68aa1
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
PCI devices starting from 18 are processor configuration devices for each
node and are not a bus itself.
According to ACPI specification 6.3 section 6.1.5:
"... _HID object must be used to describe any device that will be
enumerated by OSPM. OSPM only enumerates a device when no bus enumerator
can detect the device ID. ... Use the _ADR object to describe devices
enumerated by bus enumerators other than OSPM."
PCI device 18 with its functions has a standard enumerator, which is PCI
enumerator so it needs a _ADR. Create a separate ACPI device for the
processor configuration space. This fixes the ACPI compliance problem
from CB:36318.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ie7b45ce8d9e4fdd80d90752bf51bba4d30041507
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37835
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MIC1 NID is configured incorrectly because of a typo. The value is 7
digits instead of 8. This is corrected by this patch.
No issues are known because of this (the MIC is not connected).
BUG=N/A
TEST=build
Change-Id: Ia12f3be7d7262829cce3400a8535a33ea1c54b78
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FSP logo handling used PcdLogoPtr and PcdLogoSize which are elements of
the chipset specific FSP structures.
Create soc_load_logo() which will pass the logo pointer and size.
This function will call fsp_load_logo which will load the logo.
BUG=NA
TEST= Build and verified logo is displayed on Facebook FBG1701
Change-Id: I86943e64ca1ddd05e7e88fc6b882cfd33b98272e
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37791
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is to remove min/max() from <stdlib.h>.
Change-Id: Ica03d9aec8a81f57709abcac655dfb0ebce3f8c6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37818
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use MIN() and MAX() defined in commonlib/helpers.h
Change-Id: I02d0a47937bc2d6ab2cd01995a2c6b6db245da15
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37454
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Print error message before error return for better debugging.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I52039dcab72c6295dfb6b887a7000a6d2bd050ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Mathew King <mathewk@chromium.org>
No improvement was measured with this applied.
Change-Id: I99166e03f2580828c66305326f5141d956707f08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37754
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adding extra USB configuration since Puff has different USB ports compared to hatch
BRANCH=none
BUG=b:146437609
TEST=none
Change-Id: I42ef6b6b718274953711c84ebe90971f108501fa
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Missing bus init for RTL8111H ethernet chip hanging on bus.
V.2: Include admendments from Kangheui.
BRANCH=none
BUG=b:146437819
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I22aba312f183ea05eeb81d326ca0c05ce340a2e8
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Seems nothing special is needed here from coreboot.
V.2: Fix typo as well in speed map.
BRANCH=none
BUG=b:143047058
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: Ief750f98677b2017af78fb0b5bc98e1492dedbe4
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Remove the old Stoney Ridge postcar stack frame setup. Reduce
romstage.c to basic functionality. Until AGESA's reporting of
memory configuration is available, use the TOM register as an
indicator for the top of usable memory.
Change-Id: I516b79c3e798f5fc68c2771b2f66034c6867b19e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
No AGESA v5 binaryPI features are still present in the picasso directory.
Remove the PI and S3 selects. Remove DCACHE symbols. Remove all vboot
options until the new PSP-based solution is developed.
Change-Id: I6542578afafc0ee3c3117a971b1a021dbe53f42c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If stage cache is enabled, we should not allow S3 resume
to load firmware from non-volatile memory.
This also adds board reset for failing to load postcar
from stage cache.
Change-Id: Ib6cc7ad0fe9dcdf05b814d324b680968a2870f23
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It was possible to have NO_STAGE_CACHE=n and at the same time have
TSEG_STAGE_CACHE=n and CBMEM_STAGE_CACHE=n. This resulted with a
failing attempt to load STAGE_POSTCAR from the stage cache, but not
loading it from CBFS either.
Make it a three-way choice between different STAGE_CACHE options.
For AGESA disable CBMEM_STAGE_CACHE by default, as it is no longer
needed to have functional ACPI S3 resume and it is not allowed
se use keyword select for symbols inside choice blocks.
Change-Id: I0da3e1cf4c92817ffabbb02eda3476ecdfdfa278
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37683
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Patrick Rudolph