If the device doesn't return a valid component type, that means the
device is non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare DW_apb_i2c Databook v2.02a. It also
matches what the Picasso PPR says.
I also print out the version field of the controller.
BUG=b:153001807
BRANCH=none
TEST=Tested on PSP where I2C is non functional. Also tested on trembyle
and verified i2c was initialized.
Saw the following in the logs
I2C bus 2 version 0x3132322a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If5527972508e0f4b35cc9ecdb1491b1ce85ff3af
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2144540
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40870
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct comment on HMRFPO_ENABLE flow for CSE Lite SKU. In order to place
CSE into SECOVER_MEI_MSG mode, below procedure has to be followed.
1. Ensure CSE boots from RO(BP1).
- Set CSE's next boot partition to RO
- Issue GLOBAL_RESET HECI command to reset the system
2. Send HMRFPO_ENABLE command to CSE. Further, no reset is required.
TEST=Verified on hatch
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I213e02ba3898194fa6c8fe38fab34b5c19f25aa1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41340
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on Fibocom HW user manual RESET should be deasserted at least 20ms after the power on pin.
The design for the reset pin is open drain connected to a pull up, so it is set to high-Z (configured as GPIO in) after 20ms.
BUG=b:152013143
BRANCH=none
TEST=traced the signals using a scope to verify timing is met.
Signed-off-by: Alex Levin <levinale@chromium.org>
Change-Id: I7c947d1bc4cce1f97383a2f2c254986e182661c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Power key is a special non-matrixed key. Chrome /powerd
only listens to the keyboard device for this key, so add
its keymap.
BUG=b:155941390
TEST=Test that power key generates KEY_POWER in linux evtest
Change-Id: I570602d9febcb5c17e58761f2004ee88be16c27f
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configuring pull for SD-card detect pin.
Without this SD-card detection is not working as expected
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Change-Id: I77bf355a049224784a160defa6bee66d0f9ceb75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). This change fixes the order by adding resources in
read_resources().
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I49ce6ac88c4cb7cd05ff9d78133593ce97304596
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41374
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). This change fixes the order by adding resources in
read_resources().
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I419be7edf289636b24b9a7d6c390866ade638de3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). This change fixes the order by adding resources in
read_resources().
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I16f0439679471366723a0084918a20cd95834831
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). This change fixes the order by adding resources
during read_resources().
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I532f508936d5ec154cbcb3538949316ae4851105
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). This change fixes the order by adding resources in
read_resources().
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I84c1ba8645b548248a8bb8bf5bc4953d3be12475
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Keith Hui <buurin@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The chipset code was incorrectly adding memory resources
to the domain device after resource allocation occurred.
It's not possible to get the correct view of the address space,
and it's generally incorrect to not add resources during
read_resources(). Fix the order by hanging the resources off
of the host bridge device.
Change-Id: I8a7081020be43da055b7de5a56dd97a7b5a9f09c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
GPIO B11 pin should be configured as PMCALERT function. This is
required for the intergrated USB-C feature to work in the SOC
BUG=b:154778458, b:156288164
TEST= build and boot coreboot image on deltan. Test Type-C port
enumeration on Chrome OS
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I8f995901b0a50d2c74f57aba96f86134c9d569e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41378
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses cpu_phys_address_size() to calculate the size of high
MMIO region instead of a macro for each SoC. This ensures that the
entire range above TOUUD that can be addressed by the CPU is used for
MMIO above 4G boundary.
Change-Id: I01a1a86c0c65856f9f35185c2f233c58f18f5dfe
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There should be no harm in advertising the MMIO window above 4G in
ACPI tables unconditionally. OS can decide whether or not to use the
window. This change removes the config option enable_above_4GB_mmio
and instead adds the correct MMIO window (above 4G) details to ACPI
tables always.
Change-Id: Ie728f6ee7f396918e61b29ade862b57dac36cb08
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41276
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change sets the base for MMIO above 4G to TOUDD. It matches what
is used by resource allocator if MMIO resources are allocated above 4G
and also matches the expectation in northbridge.asl. This change
also gets rid of the macro ABOVE_4GB_MEM_BASE_ADDRESS since it is now
unused.
BUG=b:149186922
TEST=Verified that kernel does not complain about MMIO windows above
4G.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ibbbfbdad867735a43cf57c256bf206a3f040f383
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is based on autoport and that for X230. Major differences are:
- Only one DDR3 slot
- HM77 PCH
- M.2 socket instead of mini pci-e
- no docking
- no tpm
Tested:
- CPU i5-3337U
- Slotted DIMM 8GiB
- Camera
- pci-e and usb2 on M.2 slot with A key for wlan
- sata and usb2 (no superspeed components) on M.2 slot with B key for wwan
- On board SDHCI connected to pci-e
- USB3 ports
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- Sound
- Thinkpad EC
- S3
- Linux 4.9 within Debian GNU/Linux stable, loaded from
Seabios.
Untested:
- Touch screen, which is said to work under ubuntu but not debian.
Change-Id: Ie537645d5ffaee799e79af2f821f80c3ebd2dfec
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch adds a SPI rom region RW_SPD_CACHE on Puff and it can be used
on spd_cache to reduce reading SPD data from SODIMM by smbus. It's for
saving the boot time and it can be used to trigger MRC retraining when
memory DIMM is changed.
BUG=b:146457985
BRANCH=None
TEST=Build puff successfully and verified below two items.
1. To change memory DIMM can trigger retraining.
2. one DIMM save the boot time : 158ms
two DIMM save the boot time : 265ms
Change-Id: I8d07fddf113a767d62394cb31e33b56f22f74351
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This patch adds some spd_cache functions. They are for implementing the
spd_cache. It's for reducing the SPD fetch time when device uses SODIMMs.
The MRC cache also includes SPD data, but there is no public header file
available to decode the struct of MRC. So SPD cache is another solution.
BUG=b:146457985
BRANCH=None
TEST=Build puff successfully and verified below two items.
one DIMM save the boot time : 158ms
two DIMM save the boot time : 265ms
Change-Id: Ia48aa022fabf8949960a50597185c9d821399522
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This patch adds the get_spd_sn function. It's for reading SODIMM serial
number. In spd_cache implementation it can use to get serial number
before reading whole SPD by smbus.
BUG=b:146457985
BRANCH=None
TEST=Wrote sample code to get the serial number and ran on puff.
It can get the serial number correctly.
Change-Id: I406bba7cc56debbd9851d430f069e4fb96ec937c
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40414
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adds SPD_LPDDR4X_556b_1R_32Gb_8GbD_QDP_4267.spd.hex, which will be used
initially for the "H9HKNNNCRMBVAR-NEH" SKhynix part as DRAM ID #0.
Adds SPD_LPDDR4X_556b_1R_64Gb_16GbD_QDP_4267.spd.hex, which will be
used initially for the "MT53E1G64D4SQ-046 WT:A" Micron part as
DRAM ID #1.
BUG=b:155423877
TEST=none
Change-Id: I5580f602cd411e415dafcb36bd1ffa43c4f02f60
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41076
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Add SPD_LPDDR4X_200b_1R_16Gb_16Row_DDP_4267.spd.hex, initially
used for the SKhynix H9HCNNNBKMMLXR-NEE part with DRAM ID #2
- Add SPD_LPDDR4X_200b_2R_64Gb_ODP_4267.spd.hex, initially
used for the SKhynix H9HCNNNFAMMLXR-NEE part with DRAM ID #3
- Add SPD_LPDDR4X_200b_2R_32Gb_QDP_4267.spd.hex, initially
used for the Micron MT53E1G32D2NP-046 WT:A part with DRAM ID #4
BUG=b:147857288
TEST=none
Change-Id: I60d8bb05a4d6d3608adc7de69efc8623d1ca610d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41126
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mainboard specific dock-init mechanism introduced
https://review.coreboot.org/c/coreboot/+/36093 works on most boards,
but https://ticket.coreboot.org/issues/256 shows that some boards
(e.g. x201 and t410) need communication with h8 EC to enable or
disable dock, (in dock_connect() and dock_disconnect() respectively)
so they must be done after the h8 EC is brought up, which is not
garanteed in the above mainboard specific dock-init mechanism.
This time, a hook function h8_mb_init() will be called at the end of
h8_enable(). (in place of the ancient h8_mainboard_init_dock() removed
in CB:36093) Its default implementation is a weak empty function, but
could be overrided with a strong one for boards needing to perform
actions which should be done after h8 EC is brought up.
This should fix the regression detected in
https://ticket.coreboot.org/issues/256
Change-Id: I3674fbfeab2ea2cd2a4453a8e77521157d553388
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change selects SOC_AMD_COMMON_BLOCK_HAS_ESPI which enables
the capability for using eSPI on Picasso.
Additionally, it also calls espi_setup() and espi_configure_decodes()
if mainboard enables use of eSPI and skips LPC decodes in that case.
BUG=b:153675913,b:154445472
Change-Id: I4876f1bff4305a23e8ccc48a2d0d3b64cdc9703d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This change adds a helper function espi_setup() which allows SoCs to
configure connection to slave. Most of the configuration is dependent
upon mainboard settings in espi_config done as part of the device
tree. The general flow for setup involves the following steps:
1. Set initial configuration (lowest operating frequency and single mode).
2. Perform in-band reset and set initial configuration since the
settings would be lost by the reset.
3. Read slave capabilities.
4. Set slave configuration based on mainboard settings.
5. Perform eSPI host controller configuration to match the slave
configuration and set polarities for VW interrupts.
6. Perform VW channel setup and deassert PLTRST#.
7. Perform peripheral channel setup.
8. Perform OOB channel setup.
9. Perform flash channel setup.
10. Enable subtractive decoding if requested by mainboard.
BUG=b:153675913
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I872ec09cd92e9bb53f22e38d2773f3491355279e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41272
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Memory SPD files for each variant are now stored in the variant's
mb/google/volteer/variants/<variant_name>/spd directory instead
of storing them in mb/google/volteer/spd.
This change moves SPDs to where they are needed and changes the
makefile to look for them in their new locations.
BUG=b:156126658
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
a proto2 SKU4 to the kernel.
Change-Id: I759c979027477a2a4c5489a6b12278799488d6e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41184
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To change frequency, the SOC PLL team suggests procedure below:
First, we need to enable the intermediate clock and
switch the ca53 clock source to the intermediate clock.
Second, disable the armpll_ll clock output.
Third, raise armpll_ll frequency and enable the clock output.
The last, switch the ca53 clock source back to armpll_ll and
disable the intermediate clock.
BUG=b:154451241
BRANCH=jacuzzi
TEST=Boots correctly on Jacuzzi.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: Ib9556ba340da272fb62588f45851c93373cfa919
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41077
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates espi_debug.c to use switch case instead of if-else
for operating frequency and i/o mode prints. This is done to address
the review comments received on CB:41254.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I4f323b79f030818e2daa983d4f17ddf7a3192171
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41346
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:41194 got rid of "this file is part of" lines. However, there are
some changes that landed right around the same time including those
lines. This change uses the following command to drop the lines from
new files:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic3c1d717416f6b7e946f84748e2b260552c06a1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41342
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Immediately following FSP-S, update the data fabric routing
registers to make the region between HPET and LAPIC as non-posted.
If AGESA is modified to do this, we can delete data_fabric_util.c. If
AGESA is modified to not program the registers, then we can simplify
data_fabric_set_mmio_np().
BUG=b:147042464, b:156296146
TEST=boot trembyle
Change-Id: Idbafaac158f5a4c533d2d88db79bb4d6244e5355
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41268
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These are used to setup the data fabric.
Definitions came from 55570-B1 Rev 3.14 - PPR for AMD Family 17h Model 18h
BUG=b:147042464
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib51f6e2fd304da9948d6625608af71f25b974854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41266
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Family 17h devices are designed with a new internal architecture,
frequently referred to as the data fabric. Although designed to
behave somewhat like the older integrated northbridge designs,
the D18Fx definitions are completely new.
The previous northbridge.c was copied from stoneyridge which is
completely different.
Change-Id: Id70cbda99657249179fb8cf5e461dd6a37ec9153
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41265
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a device specific register, not a northbridge register.
BUG=b:147042464
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I97b63571e336f541dcb274e4c8c608f6fc59ff42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41263
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When any USB image disk is connected to the DUT through
HUAWEI/APPLE Dongle, press Ctrl + u on the dev screen,
it cannot boot from USB.
We found the SS hub cannot be enumerated. So disable xHCI
compliance mode.
BRANCH=octopus
BUG=b:155347573
TEST=Confirm successful boot from USB
Change-Id: Iea4a3df156da0627336f7d6c1e03837b6cf0e7f2
Signed-off-by: tong.lin <tong.lin@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40905
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a helper function lpc_early_init() which does the
following things:
1. Enables LPC controller
2. Disables any LPC decodes (These can be set up later by SoC or
mainboard as required).
3. Sets SPI base so that MMIO base for SPI and eSPI controllers is
initialized.
BUG=b:153675913
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I016f29339466c3fee92fe9b62a13d72297c29b8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Picasso has an LPC and eSPI bridge on the same PCI DEVFN. They can both
be active at the same time. This adds a way to specify which devices
belong on which bus.
i.e.,
device pci 14.3 on # - D14F3 bridge
device espi 0 on
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device lpc 0 on
end
end
BUG=b:154445472
TEST=Built trembyle and saw static.c contained the espi bus.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0c2f40813c05680f72e5f30cbb13617e8f994841
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The default setting of the root port ASPM configuration can be
overridden from the device tree by using a non zero value.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I85c545d5eacb10f43b94228f1caf1163028645e0
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Raul E Rangel