The patch implements an API that stores the CSE firmware version in the
CBMEM table. The API will be called from RAMSTAGE based on boot state
machine BS_PRE_DEVICE/BS_ON_EXIT
Additionally, renamed ramstage_cse_fw_sync() to ramstage_cse_misc_ops()
in order to add more CSE related operations at ramstage.
This patch also adds a configuration option,
'SOC_INTEL_STORE_CSE_FPT_PARTITION_VERSION', which enables the storage
of firmware version information in CBMEM memory. This information can be
used to identify the firmware version that is currently installed on the
system. The option depends on the `DRIVERS_INTEL_ISH` config and
platform should be flexible enough to opt out from enabling this
feature.
The cost of sending HECI command to read the CSE FPT is significant
(~200ms) hence, the idea is to read the CSE RW version on every cold
reset (to cover the CSE update scenarios) and store into CBMEM to
avoid the cost of resending the HECI command in all consecutive warm
boots.
Later boot stages can just read the CBMEM ID to retrieve the ISH
version if required.
Finally, ensure this feature is platform specific hence, getting
enabled for the platform that would like to store the ISH version into
the CBMEM and parse to perform some additional work.
BUG=b:273661726
TEST=Able to build and boot google/marasov.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I923049d2f1f589f87e1a29e1ac94af7f5fccc2c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
The mp2 PCI device is still present when no mp2 firmware is loaded. When
this device isn't explicitly enabled in the mainboard's devicetree, the
chipset devicetree default of the device being disabled is used. This
results in coreboot's resource allocator not allocating resources to
the device and since the bridge doesn't have enough MMIO space reserved,
the Linux kernel can't assign resources to it. Enable the mp2 device in
the mainboard's devicetree so that it gets its resources assigned by
coreboot.
BUG=b:277217097
TEST=builds
Change-Id: I21885c51ff08846b456675090946f381843ef5e6
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74277
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Because WD SSD drive isn't holding the clock low for some reason.
So we change to read eMMC clkreq signal instead.
BRANCH=none
BUG=b:278495684
TEST=emerge-skyrim coreboot chromeos-bootimage and verify ok.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I3a9225473a6ae1ba01dc8e5d982c4999f073267e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74583
Reviewed-by: Chao Gui <chaogui@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
TEST=Timeless build for pcengines/apu2 results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If96f4655a3b4dc621ef77c4d97d2927565d634ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Use coreboot's native PCI access functions instead of using the
vendorcode's PCI access functions to set up the CPU IO routing in
function 1 of the HT PCI device. This file still has room for
improvement, but at least it's now using coreboot-native functionality.
Stoneyridge has a nicer implementation, but looking into possibly
unifying those is out of scope for this patch.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieecc0e5f6576a838d79220b061de81e21b5d976c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
When one of the General-Purpose PCIe bridges is not used, it doesn't
show up on the PCI bus at all, so coreboot notes it as an issue in the
devicetree. This happens even if the device is marked as off.
To solve this, we're marking the GPP bridge devices in devicetree as
hidden, so they'll only show up in devicetree if they're actually used
on a mainboard.
BUG=b:277997811
TEST=Build
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I7b7577baa2dbb0ea7ebbcdb1a8ae81770e61d76f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74527
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When one of the General-Purpose PCIe bridges is not used, it doesn't
show up on the PCI bus at all, so coreboot notes it as an issue in the
devicetree. This happens even if the device is marked as off.
To solve this, we're marking the GPP bridge devices in devicetree as
hidden, so they'll only show up in devicetree if they're actually used
on a mainboard.
BUG=None
TEST=Don't see the "PCI: Leftover static devices:" warning for these in
the boot console.
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I517776e4dedc70e957a0c836ab3c2e5d49e156d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74526
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This change adds the VPU into the DMAR SATC table in order to support
the VPU IO virtualization.
BUG=None
TEST=Enabled the VPU, booted to kernel and verified that DMAR SATC table
includeded the VPU entry.
Change-Id: I6d4af7c9844e33483a1e616eaee061a90d0be6fc
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This patch refactors cse_fw_sync() function to include timestamp
associated with the CSE sync operation.This effort will ensure the
SoC code just makes a call into the cse_fw_sync() without bothering
about adding timestamp entries.
TEST=Able to build and boot google/marasov.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib5e8fc2b8c3b605103f7b1238df5a8405e363f83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Use get_top_of_mem_below_4gb instead of open-coding the functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icc9e5ad8954c6203fc4762aa976bba7e8ea16159
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Use get_top_of_mem_below_4gb instead of open-coding the functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic673deb725a541c7535ae769f589cd82ea42a561
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Use get_top_of_mem_below_4gb and get_top_of_mem_above_4g instead of
open-coding the functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I04f2a3744aee9beedaa97b154a652ce6f0c705c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Use get_top_of_mem_below_4gb and get_top_of_mem_above_4g instead of
open-coding the functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I35895340f6e747e2f5e1669d40f40b201d8c1845
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
To use generated build.h one should have had a pre-requisite in the
Makefile. Reference coreboot_build_date from lib/version.c instead.
Change-Id: Icd6fa2ddf8aa584b0f51ba130592f227bbdad975
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
To use generated build.h one should have had a pre-requisite
in the Makefile. Reference coreboot_version from lib/version.c
instead.
Change-Id: I7f10acabf1838deb90fde8215a32718028096852
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use get_top_of_mem_below_4gb and get_top_of_mem_above_4g instead of
open-coding the functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6332b051acf8d00ba6528360b18ea0d3c4dc30fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
The top of memory below 4GB will always fit into 32 bits, so change the
return type accordingly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b463a17f2db3b7a99ff3572f318c9c22aac7431
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Rename amd_topmem and amd_topmem2 to get_top_of_mem_below_4gb and
get_top_of_mem_above_4g to make it clearer what those functions return.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic6e98d94c731af74aea0ce276a9a7e4867e3986f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Set up SoC-specific XHCI defines and enable SOC_AMD_COMMON_BLOCK_XHCI
to allow for XHCI events to be logged.
BUG=b:277273428
TEST=builds
Change-Id: I3ca4f84fb0f1fef8441ab6ef7b6f6348c52b2922
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74280
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure GSC I2C and Interrupt GPIOs during the early initialization.
Add devicetree configuration for GSC device and enable the required
config items.
BUG=b:275959717
TEST=builds
Change-Id: I6e235356b252a7b68a42da128ffd3189a829f117
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74111
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
C0 clock throttling was disabled, no need to add _PTC.
C2/C3 latency values were copy-paste from different CPUs.
TBD: Check IO-trap
Change-Id: Ia0e35e28f0df8b0f8fc58f70c7d792487ee4f7f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74439
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
After the obsoletion of Processor() it is necessary to provide
_PTC package to define P_CNT IO address for clock throttling.
The platforms touched here already emit empty _PTC to disable
clock throttling.
Change-Id: I0e84c8ccd2772c9b3d61f71b74324c8d28f4eefe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74438
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After the obsoletion of Processor() it is necessary to provide
_CST package to define P_LVLx IO addresses for C2/C3 transitions.
The latency values from _CST will always replace those in FADT.
Change-Id: I3230be719659fe9cdf9ed6ae73bc91b05093ab97
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Iabba97e003d1a5140c98e3fc5a3496f66f8795c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74528
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
`is_untrusted` is eventually ended up by adding DMA property _DSD which is similar to what `add_acpi_dma_property` does for WWAN drivers,
hence it makes sense to have a unified name across different device drivers.
BUG=b:278310435
BRANCH=firmware-brya-14505.B
TEST=Verified that the _DSD object is still present in the SSDT.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I5a69a47e67f6acaad5a5d1b67e437c5a41bebf3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74499
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the boxy variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:277529068
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BOXY
Change-ID: Ief22eb000421c23abf6de3f99eb860bdae1e7919
Signed-off-by: kevin3.yang <kevin3.yang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The new pages for the P8Z77-M, P2B-LS, and P3B-F were missing from
index.md, causing Sphinx to output "document isn't included in any
toctree" warnings.
Change-Id: I7883d48bfbe6bff5595aa9303f9d6f4a55eadc9c
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
srcclk_pin is 0-based and '0' is a valid clock source number. If
srcclk_pin is set to -1, then the clock will not be disabled in D3.
Therefore, clock source gating method should not be generated.
BUG=b:271003060
BRANCH=firmware-brya-14505.B
TEST=Boot to OS and check that rtd3 ACPI entries are generated as
expected. For those PCI devices with RTD3 driver whose srcclk_pin to
0, the RTD3 entries should not be missing due to check error.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia831b8fd17572cc35765bd226d1db470f12ddd41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73889
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
This patch sends the CSE EOP command asynchronous implementation early
as part of `soc_init_pre_device`.
Without this patch the duration between asynchronous CSE EOP send and
receive commands is not ample which causes idle delay while waiting
for EOP response.
The goal of the CSE async implementation is to avoid idle delay while
capturing the response from CSE EOP cmd. This patch helps to create
ample duration between CSE EOP command being sent and response being
captured.
TEST=Able to boot google/rex sku to ChromeOS and observed ~100ms of
boot time savings (across warm and cold reset scenarios)
Change-Id: I91ed38edbd5a31d61d4888e1466169a3494d635a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Add eSPI configuration for myst. Ensure the additional windows are used
and remove unnecessary addresses from the range used on skyrim.
BUG=b:275953893
TEST=builds
Change-Id: I7b40adec78d4e0b596596fa6e2951c79bd3bd8c7
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74110
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Parts of this file were still a copy of the file from the Mendocino SoC,
so update the file to match the PPR #57019 Rev 3.03 and the chipset
devicetree of the Phoenix SoC. Phoenix has 4 GFX/GPP PCIe bridges/ports,
the numbering scheme of the GPP PCIe bridges/ports was changed so that
the numbers match the device and function numbers, and there are new
device functions for the IPU and the USB4 controller and router devices.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie9429c03839bb0199a04cd6cafe9a955ebdacc91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74565
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In both PPR #57019 Rev 3.03 and PPR #57396 Rev 3.04, the i2s_ac97
function on bus C isn't mentioned any more and the microarchitecture
specification document for this SoC also doesn't mention it, so remove
it from the devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibd115953bdd60e1dfcc79797b0c2158e5d861636
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74564
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5e067f6fb2bab66d9b2f6965636845dfd8b7cacd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove the `TcssD3ColdDisable` option in devicetree, as it exists
in Kconfig. The setting is currently unused.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I08930ef84438140a13df74900570b126088bd1cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74478
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the `TcssD3ColdDisable` option in devicetree, as it exists
in Kconfig. The setting is currently unused.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I2590e8dec0a308e0dc3d467cb3dd2bb97e877492
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74477
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the `TcssD3ColdDisable` option in devicetree, as it exists
in Kconfig. The setting is only used on `starlabs/starbook` which
selects D3COLD_SUPPORT so the UPDs will not change.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I50e49e900c96748edd5b678765e47cc0e0d9b280
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74476
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use D3COLD_SUPPORT Kconfig option to set the maximum support sleep
state. Report `4` in `_S0W` only when D3COLD_SUPPORT is enabled, as
if it is not, it will break S3 exit.
When D3COLD_SUPPORT is not enabled, return `3` (D3Hot).
This fixed S3 exit on both TGL and ADL. Tested on StarBook
Mk V and Mk VI.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I578d4933b6144aec79fe0b2eb168338ef82c0b9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74406
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The Kconfig option SOC_INTEL_TIGERLAKE_S3 suggests that it's doing
something with S3, but it's actually disabling D3Cold support.
Remove it, and instead use D3COLD_SUPPORT so it's clear what the
option is doing.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Id43f3e5c8620d474831cc02fcecebd8aac961687
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74405
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move D3COLD_SUPPORT to device, so it can be used by multiple
SOCs.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie92736458ab95374c51346107665dc0fd1e653a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74404
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add PCIe RTD3 support so the NVMe gets placed into D3 when entering s0i3
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I5eac65125c11dd04c5dbb5996c947ad734acdae3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Update DXIO descriptors for birman-phoenix per schematic 105-D67000-00B
v0.7
Update devicetree to reference the updated DXIO descriptors.
TEST=boot birman and note the devices show up in the logs correctly
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I76cf6715b60a1857bf58349d70a623bf043594fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The Intel FSP used on ChromeOS platform has dropped the
`CpuFeaturesPei.ffs` module to opt for coreboot running this
additional feature programming on BSP and APs.
TEST=Able to build and boot google/rex without any boot regression.
Please refer to the boot time and SPI flash savings after dropping
the FSP feature programming:
Boot time savings=10ms
SPI Flash size savings=34KB
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iaed0a009813098610190b2a3a985b0748c0d51de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Update the EC GPIO values for Birman, per schematic # 105-D67000-00B
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Icd9df120f555eb06f920f6263a8d2ab45c05baec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73971
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Subrata Banik