If elog_clear is called before other elog functions, for instance if it's
called through an SMI immediately after the system boots, then the elog data
structures won't have been set up and the system will go off the deep end.
This change adds a call to elog_init to elog_clear to make sure things things
are always initialized before we start using them.
Before this change, this command would cause
the system to lock up if run immediately after boot:
echo 1 > /sys/firmware/gsmi/clear_eventlog
After this change, that results in the log being cleared correctly.
Change-Id: I45027f0dbfa40ca8c581954a93b14b4fedce91ed
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49303
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Slight tweaks found when looking at latest ref code when
investigating package C-state issues.
A few bits in the clock gating register don't match the
documentation and are also cleaned up.
Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4142
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The mainboard_interrupt_handlers() argument for the function
pointer was using void * as the type. This does not allow the compiler
to catch type differences for the arguments. Thus, some code has been
committed which violates the new interrupt callbacks not taking any
arguments. Make sure the compiler provides a type checking benefit.
Change-Id: Ie20699a368e70c33a9a9912e0fcd63f1e6bb4f18
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48970
Reviewed-on: http://review.coreboot.org/4141
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some handlers still had 2 variants, others were
incorrectly guarded by CONFIG_ variables. This
patch straightens them out.
This does not touch the siemens/sitemp_g1p1 which
provides an interestingly complex solution for the
int15 handler.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5d74fdf7c2ab1faa96ebc2b5ca5c69398449b069
Reviewed-on: https://gerrit.chromium.org/gerrit/48979
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4140
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I3235f42c7faaf28a63455162ea55dc1a6bebd1f5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Hung-Te Lin <hungte@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48290
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC saves its last "shutdown reason" for the system in EC RAM
that we can read back and log on boot.
The decode for the "reason" field will be added to mosys.
Change-Id: I834d39122e45262ef8e7ba59201accbee5857aac
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48323
Reviewed-by: David James <davidjames@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4127
Tested-by: build bot (Jenkins)
Commit b8ad224 changed the memory address in lb_cbmem_ref coreboot
table entries from a pointer to a uint64_t. This change was introduced
to make the cbmem utility work on both 32bit and 64bit userland.
Unfortunately, this broke the cbmem utility running on older versions
of coreboot because they were still providing a 32bit only field for
the address while the cbmem utility would now take the following 4
bytes as upper 32bits of a pointer that can obviously not be
mmapped. This change checks if the size of the lb_cbmem_ref structure
provided by coreboot is smaller than expected, and if so, ignore the
upper 32bit of the address read.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: If4c8e9b72b2a38c961c11d7071b728e61e5f1d18
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The format of this function changed but was not updated in
all mainboards. This fixes all Sandybridge/Ivybridge boards.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Icdaae4d6d50884f6d7bce7a167d48cb1d4807010
Reviewed-on: https://gerrit.chromium.org/gerrit/48969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4135
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This imports the cache/MMU code from coreboot as of 1877cee.
Change-Id: I97ec8b9640921a94a4b27d89e4ae6185e9f96f18
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48288
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4134
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Recent commit proposal by Ron Minnich proposes to move to native gfx init for
qemu. Unfortunately we didn't have native init for default qemu video (cirrus)
Here is one extracted from GRUB one which I wrote couple of years ago.
Change-Id: Icb89cf918ef5d276bcc703c48c568e7b9c1be756
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Part of X201 port.
Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4052
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Per our discussions with Gerd, qemu will now always do native graphics
on coreboot. The VGA BIOS capability is not needed and will no longer
be supported. Attempts to build without native graphics will result in
an error.
This code builds for both x86 emulation targets. I'm hitting an issue
testing that is unrelated to coreboot; if someone can test, that
would be helpful. Be sure to start qemu with -vga std.
We also add a test for the PCI BAR being zero and return silently if it
is.
Change-Id: I66188f61e1bac7ad93c989cc10f3e0b55140e148
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4258
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Needed to make dock work on X201.
Change-Id: Id0b32266cacf04bb48530bedf50818c268f947ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4081
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
SandyBridge raminit uses this CMOS option. If it is not declared, the build
fails when USE_OPTION_TABLE is selected.
Change-Id: I1ba1f994d4ea3824dc66e8f35d0b5b24b88d4dd6
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4269
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
the part !CAR && PRE_RAM is obviously meant as dummies. Unfortunately
cbmemc_tx_byte has wrong number of arguments and hence causes compilation
failure.
Found out when compiling for vexpress-a9.
Change-Id: Ic84d142bac5c455c2371fbc9439c898de04a974e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4267
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
With the XHCI controller enabled we no longer hang the
system when dropping into a package C-state so remove
the code that was disabling it.
Change-Id: Icd60488fd2506dac04fb6ec96a77bec265b10d8c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50355
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4163
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The chromeos_acpi driver sysfs naming is not what
crossystem expects if there is just one entry in the package
because it does not add a ".#" suffix in that case.
Specify all the expected GPIOs on wtm2 as undefined, which
should be 0xFF and not 0x00 becuase 0 is a valid GPIO.
Change-Id: I9b17e9bab94219695e65b17914c84acf02a0983b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50337
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4162
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The current microcode blobs contain both ULT and non-ULT
revisions. Only include one or the other based off of the
CONFIG_INTEL_LYNXPOINT_LP Kconfig option.
Change-Id: I3e4e41d4cd727b1a974361fb469267e6f6022d5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50318
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4160
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
For all the current haswell boards enable the monotonic timer.
The ULT boards use the 24MHz MSR while the non-ULT boards use the
local apic.
Change-Id: I8b19f526a5a49e8467f296c566a2c4263bc5a863
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49763
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4148
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This reads PCH power levels via PCODE mailbox and writes the
values into the PMSYNC registers as indicated in the BWG.
Change-Id: Iddcdef9b7deb6365f874f629599d1f7376c9a190
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4143
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
On haswell ULT systems there is a 24MHz clock that continuously runs
when deep package c-states are entered. The 100MHz BCLK is shut down
in the lower c-states. When the package wakes back up a conversion
formula needs to be applied. The 24MHz calibration is done using the
internal PCODE unit.
Change-Id: I6be7702fb1de1429273724536f5af9125b98da64
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48292
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4136
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The c-states are configured according to the BWG, however the
package c-states are disabled as they currently cause platform
instability. The exposed ACPI c-state to processor c-state mapping
are as follows for ULT boards:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C7S long latency)
ACPI(C3) = MWAIT(C10)
The non-ULT boards have an expoed c-state mapping:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Included in this patch is removing the updating of current limit
registers as some of the MSRs are different and the proper values
are currently unknown. Lastly, some of the MSRs were renamed to
match the BWG.
Booted 3.8 kernel and used powertop to note package, core, and acpi
c-state residency.
Change-Id: Ia428d4a4979ba3cba44eb9faa96f74b7d3f22dfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48291
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4133
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This will be used in a later commit to do some specific
power sequencing.
Change-Id: Id7f033bb80aed915c2498ea910cb3ac7290da37f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4137
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This adds some macros for the common GPIO defines and drops
the gpio number definition from each entry. The end result
is much easier to read. The wtm2 mainboard gpio list is modified
to use this.
Also fix a bug in the LP version of get_gpio() that was always
returning zero due to a miscompare.
Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4138
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These are placeholder values until we can configure for
the exact panel.
Change-Id: Ibe88cc3588947366eb1728e5b3e1ab8c8be6dfe8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4196
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Minor tweaks to variable names in the slippy mainboard
that make it easier to base a new board from without
as much renaming.
Also properly set up the thermal variables for the
thermal zone that is defined in ACPI instead of using
the generic setup from WTM2.
Change-Id: I752c1a50bfdc06b6ddad95bd1331c6870b9f9df2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56328
Reviewed-on: http://review.coreboot.org/4183
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This will log and clear EC events so they do not take effect
when the SMI handler is enabled.
Change-Id: I5ef563f7cedc8977410cc3f69e2655fc4e14c9eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4178
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The SerialIO devices have specific requirements for PCI
interrupt mode to use PIRQ{E,F,G,H} that are not being met.
D21:F0 uses PIRQE, which must not be shared with other PCH
D21:F1-F6 share PIRQF, which must not be shared with other PCH
D23:F0 uses PIRQH, which must not be shared with other PCH
- Fix D20IR -> D20IP typo
- Remove D25/EHCI2 as it does not exist
- Reorder other interrupts to clear PIRQE/PIRQF/PIRQH
Check device interrupts in the kernel
0: IO-APIC-edge timer
1: IO-APIC-edge i8042
8: IO-APIC-edge rtc0
9: IO-APIC-fasteoi acpi
16: IO-APIC-fasteoi ath9k
18: IO-APIC-fasteoi i801_smbus
19: IO-APIC-fasteoi ehci_hcd:usb1
21: IO-APIC-fasteoi i2c-designware-pci--1, i2c-designware-pci--1
40: PCI-MSI-edge PCIe PME
41: PCI-MSI-edge i915
42: PCI-MSI-edge ahci
43: PCI-MSI-edge xhci_hcd
44: PCI-MSI-edge snd_hda_intel
Change-Id: Id4c08d11d2860f270c6387138acdc7d3d83a85b5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56028
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4176
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The dev screen was not displaying properly. With the
PWM values programmed the screen displays correctly.
Change-Id: I82b56a92e4168022082a2e519026977ee2ae0c9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51472
Reviewed-on: http://review.coreboot.org/4172
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The device at function 0 also needs to be enabled
or the kernel will ignore all other functions.
00:15.0 DMA controller: Intel Corporation Lynx Point-LP Low Power Sub-System DMA (rev 03)
00:15.1 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #0 (rev 03)
00:15.2 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #1 (rev 03)
Change-Id: I0e1bc7bb719756496c46664d66dc1b1cf2f4d1ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51370
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4171
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Without an LM10506-A the power sequencing for this
part needs to be done manually using GPIOs.
Change-Id: I842152e5f7c30c8dbe37df0c344935a659eb2887
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49648
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4150
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes an earlier patch that caused the VGA option ROM to be loaded by
coreboot even in normal mode when it isn't needed.
Change-Id: Ie0a331a10fff212a2394e7234a0dbb37570607b7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48173
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4125
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Not all platforms !x86 are big endian, hence actually look
at the CONFIG_LITTLE_ENDIAN flag instead of CONFIG_ARCH_X86.
Change-Id: Ibbd8f48b377a1121dd1e045834a94a2d67eda2ab
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/56066
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/4236
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: Ieaaaa2611f7bb8968f01b16daefe7e2afe870f72
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: I4e88c26b70ea8cb249d7613c749b3edc5e3b5e7f
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4000
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Without that fix the GTT points at 0x00000000.
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: Ia378b600ba2faf00d42635c6503b94ff0cb1bc8c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Move into src/cpu/dmp/dmp_post_code.h
Change-Id: If9f4d842f352eb41618e71f49a226d3cc4ad0b46
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3989
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Gabe Black