This imports the cache/MMU code from coreboot as of 1877cee.
Change-Id: I97ec8b9640921a94a4b27d89e4ae6185e9f96f18
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48288
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4134
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Not all platforms !x86 are big endian, hence actually look
at the CONFIG_LITTLE_ENDIAN flag instead of CONFIG_ARCH_X86.
Change-Id: Ibbd8f48b377a1121dd1e045834a94a2d67eda2ab
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/56066
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/4236
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It is for crossgcc.
Change-Id: Ia1d676adfea340b6b80858215459491c9338d614
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3955
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
On Intel's Panther Point the xHCI ports are shared with an EHCI
controller. Our xHCI driver switches them to xHCI, naturally. But
we forgot to switch them back on shutdown, which left them
unusable by a non-xHCI aware operating system.
Change-Id: I70ef08655a603b42ee939935d50cf77ea97878a3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3791
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
keyboard_init attempts to read the existing mode register, set the
'XLATE' bit, and write it back. The implementation is buggy because the
keyboard may be active at the time we read the mode, and we can
misinterpret scancode data as the reply to our command. It leads to
problems where the KB gets disabled in firmware.
In fact, setting the 'XLATE' bit is completely unnecessary, even if we
desire QEMU keyboard support. We already set this bit when we initialize
the keyboard in pc_keyboard_init. Basically, this code does nothing
(or worse), so just remove it.
Change-Id: Iab23f03fa8bced74842c33a7d263de5f449bb983
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/3883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For libpayload clients with larger memory needs (eg. FILO with integrated
flashrom) the current configuration isn't enough.
Change-Id: Ic82d6477c53da62a1325400f2e596d7d557d5d1e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3889
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Change-Id: Ie69ceb343494b7dd309847b7d606cb47925f68b6
Reviewed-on: http://review.coreboot.org/3888
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Prettier in real-world payloads (ie. FILO)
Change-Id: I9ed968fe527c5d46090e707e2d89b7406a43662e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3887
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
flashrom has started to use revision IDs to distinguish AMD chipsets
and fails (even more) to build with libpayload since then because
PCI_REVISION_ID is undefined in libpayload's pci header.
Change-Id: If7440a48c1005a4ba4fc09303f47cdfa9f408ad1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3884
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For reasons explained in a previous CL, it might be necessary to "load" a file
from CBFS in place. The loading code in CBFS was, however, zeroing the area of
memory the stage was about to be loaded into. When the CBFS data is located
elsewhere this works fine, but when it isn't you end up clobbering the data
you're trying to load. Also, there's no reason to zero memory we're about to
load something into or have just loaded something into. This change makes it
so that we only zero out the portion of the memory between what was
loaded/decompressed and the final size of the stage in memory.
Change-Id: If34df16bd74b2969583e11ef6a26eb4065842f57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The memset and memcpy functions are assembled as ARM code, likely because
that's the default of the assembler. Without special annotation, the assembler
and linker don't know that those symbols are functions which need special
handling so that ARM/thumb issues are handled properly. This change adds that
annotation which gets those functions working in Coreboot which is compiled as
thumb. Libpayload and depthcharge are compiled as ARM so they don't *need* the
annotation since it just works out in ARM mode, but it's the safe thing to do
in case we change that in the future.
We should explicitly select ARM vs. thumb when assembling assembly files to be
consistent across builds and toolchains.
Change-Id: I814b137064cf46ae9e2744ff6c223b695dc1ef01
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3672
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The counted delay of 1ms was shorter than the time usb_poll() took
(~30ms observed). So with a given timeout of 100ms it actually took 3s.
We can lower the problem if we delay 10ms per loop iteration.
Change-Id: I6e084bdd05332111cc8adcd13493a5dfb4bc8b28
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3533
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Teach lpgcc to look in the in-coreboot tree directory structure, too.
Change-Id: I3809456d072ce2f91542b0edb3fd39f536298cc2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3530
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We can't read the drives signature before it's ready, i.e. spun up.
So set the timeout to the standard 30s. Also put a notice on the
console, so the user knows why the signature reading failed.
Change-Id: I2148258f9b0eb950b71544dafd95776ae70afac8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A timeout while waiting for a device' signature has shown that our
error path wasn't correct. The shutdown of the ports command engine
always timed out. Fix that by waiting for FR (FIS Receive Running)
to be cleared independently from CR (Command List Running) and after
clearing FRE (FIS Receive Enable).
Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3494
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These values are already used in this usb stack.
Change-Id: If96f1dc2b67fbc13dfc4ae2d84e8f9945aa03163
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3448
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Add the Mobile Panther Point (PPT) AHCI controller (DEVID 0x1e03) to
the list of tested controllers. Also comment the only other listed
controller (Mobile ICH9).
The PPT AHCI controller was tested with a QM77 chipset on a Kontron
KTQM77 board.
Change-Id: Ia396761411f4f9289af11ec8e1b144512b2fc126
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes the configuration where serial console output is
being sent to non-existant hardware to be captured with I/O
trapping. In this configuration where there isn't serial
hardware present we still want to init the consoles. We just
never want to read non-existant hardware.
Change-Id: Ic51dc574b9c0df3f6ed071086b0fb2119afedc44
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3249
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The cbfs core code would print out the name of the file it is
searching for and when it is found would print out the name
again. This contributes to a lot of unnecessary messages in a
functioning payload’s output. Change this message to a DEBUG one
so that it will only be printed when CONFIG_DEBUG_CBFS is enabled.
Change-Id: Ib238ff174bedba8eaaad8d1d452721fcac339b1a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3208
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The cbfs core code would print out all unmatched file
names when searching for a file. This contributes to a lot
of unnecessary messages in the boot log. Change this
message to a DEBUG one so that it will only be printed when
CONFIG_DEBUG_CBFS is enabled.
Change-Id: I34c747e0d3406351318abf70994dbc0bb3fa6c01
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3164
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Because pointers can be 32bit or 64bit big,
using them in the coreboot table requires the
OS and the firmware to operate in the same mode
which is not always the case. Hence, use 64bit
for all pointers stored in the coreboot table.
Guess we'll have to fix this up once we port to
the first 128bit machines.
Change-Id: I46fc1dad530e5230986f7aa5740595428ede4f93
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3115
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The way we got to include the compiler includes was kind of whacky.
Instead of mixing in potentially problematic headers, make libpayload
self-contained by adding some missing header files. Also clean up
conflicting definitions of size_t throughout the tree.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I0ad1194de1a00b7133c5477c00eb167d63a2ee85
Reviewed-on: https://gerrit.chromium.org/gerrit/47608
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3058
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reading commit »libpayload: New AHCI, ATA and ATAPI drivers«
(1f6bd94f) [1], the spelling error was found and is now fixed.
[1] http://review.coreboot.org/1622
Change-Id: Id418bcb99c1a9a400a49fc04078e465bd0908074
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3071
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change modifies the code in libpayload that scans the PCI hierarchy for
USB controllers. Previously, if a devices primary function (function 0) was a
bridge, then none of the other functions, if any, would be looked at. If one
of the other functions was a bridge, that wouldn't be handled either. The new
version looks at each function that's present no matter what, and if it
discovers that it's a bridge it scans the other side.
Change-Id: I37f269a4fe505fd32d9594e2daf17ddd78609c15
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2517
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Nico Huber spotted [1], that commit (4d6ab4e2) [1] updating
superiotools’s `README` with the Git command line
superiotool: Update README with Git repository URL and directory location
missed, that after `git clone` one sitll has to change into
the cloned directory.
So prepend the path with `coreboot/` to fix that. The same error
happened in the commit (e1ea5151) for libpayload [2]
libpayload: Update README with Git repository URL and directory location
and is fixed in this patch too.
[1] http://review.coreboot.org/#/c/3019/
[2] http://review.coreboot.org/2228
Change-Id: Ib6e8b678af6276556a40ccfd52ae35ca7e674455
Reported-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3021
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Building libpayload with the PDCurses backend the following warning
is shown.
/src/coreboot/payloads/libpayload(master) $ make clean
/src/coreboot/payloads/libpayload(master) $ make
[…]
CC curses/pdcurses-backend/pdcscrn.libcurses.o
curses/pdcurses-backend/pdcscrn.c: In function 'PDC_scr_open':
curses/pdcurses-backend/pdcscrn.c:75:5: warning: "CONFIG_SPEAKER" is not defined [-Wundef]
[…]
The GCC documentation states [1]
In some contexts this shortcut is undesirable. The -Wundef option
causes GCC to warn whenever it encounters an identifier which is
not a macro in an ‘#if’.
and therefore use `#ifdef` [2] to silence this warning. No functional
change is done, as `CONFIG_SPEAKER` is assigned the value `Y` when
defined.
There was some discussion going on the list [3], but my points in there
turned out to be incorrect.
[1] http://gcc.gnu.org/onlinedocs/cpp/If.html
[2] http://gcc.gnu.org/onlinedocs/cpp/Ifdef.html
[3] http://www.coreboot.org/pipermail/coreboot/2013-March/075561.html
Change-Id: I8e9c9b5d01985b21ad05018986d614cf9bf2b439
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2934
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
This imports the newest cache and MMU code from coreboot. This
time it's so new that it hasn't even been checked in to coreboot.
However, this version at least allows DMA to work properly for the
MSHC driver. So even if we rebase a few more times, this version is
at least a step in the right direction.
Note: This omits the stuff that sets up dcache policy since
libpayload should not need to worry about that and it depends
on cbmem stuff.
Change-Id: Idd42b083e8019634aaaa44d5bf5b51db6c3912f5
Signed-off-by: David Hendricks <dhendrix@google.com>
Reviewed-on: http://review.coreboot.org/2975
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
This imports the new cache maintenance API from coreboot at
commit bba8090. This is a BSD-licensed implementation which
exposes cache maintenance opertaions necessary for payloads
for things such as DMA transfers.
Change-Id: I554676db89517bebc6edae4f7ab7e5882e6f986d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2974
Tested-by: build bot (Jenkins)
On x86, coreboot may allocate a variable range MTRR for enabling caching
of the system ROM. Add the ability to parse this structure and add the
result to the sysinfo structure.
An example usage implementation would be to obtain the variable MTRR
index that covers the ROM from the sysinfo structure. Then one would
disable caching and change the MTRR type from uncacheable to
write-protect and enable caching. The opposite sequence is required
to tearn down the caching.
Change-Id: I3bfe2028d8574d3adb1d85292abf8f1372cf97fa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2920
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes the following PDCurses warnings:
CC curses/pdcurses-backend/pdcsetsc.libcurses.o
curses/pdcurses-backend/pdcsetsc.c: In function 'PDC_curs_set':
curses/pdcurses-backend/pdcsetsc.c:17:9: warning: implicit declaration of function 'serial_cursor_enable' [-Wimplicit-function-declaration]
curses/pdcurses-backend/pdcsetsc.c:22:9: warning: implicit declaration of function 'video_console_cursor_enable' [-Wimplicit-function-declaration]
CC curses/pdcurses-backend/pdcutil.libcurses.o
curses/pdcurses-backend/pdcutil.c:30:6: warning: no previous prototype for 'curses_enable_serial' [-Wmissing-prototypes]
curses/pdcurses-backend/pdcutil.c:35:6: warning: no previous prototype for 'curses_enable_vga' [-Wmissing-prototypes]
curses/pdcurses-backend/pdcutil.c:40:5: warning: function declaration isn't a prototype [-Wstrict-prototypes]
curses/pdcurses-backend/pdcutil.c:45:5: warning: function declaration isn't a prototype [-Wstrict-prototypes]
Change-Id: If0d4d475d3006f1a77f67ec46c6bdf4ee2906981
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2908
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There were a number of type issues in libpayload that sneaked in
with 903f8e0.
- size_t and ssize_t were conflicting with gcc builtins
- some stdint types were used in libpayload but not defined
in our stdint.h
With this patch it's possible to compile libpayload with the
reference toolchain again.
Change-Id: Idd5ccfdd9f3536b36bceca2d101e7405883b10bc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2903
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
libcbfs was using printf for size_t typed variables. However, printf
did not support printing those. This patch fixes the issue, removing
the warning when compiling ram_media.c
libcbfs/ram_media.c:52:10: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
libcbfs/ram_media.c:52:10: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat]
Change-Id: Iaf6e723f9a5b0a61a39d3125036fee9853e37ba8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2904
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The keyname() and termname() functions were creating a whole lot of warnings of
the style
curses/PDCurses-3.4/pdcurses/keyname.c:41:9: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This patch fixes them.
Change-Id: Iae3c4e5201b48c2d2033cac48577e0462a34f309
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2905
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
PDCurses has a function called overlay() and also uses
overlay as a variable name in some functions.
This patch fixes the ambiguity that caused warnings like
curses/PDCurses-3.4/pdcurses/overlay.c: In function '_copy_win':
curses/PDCurses-3.4/pdcurses/overlay.c:51:39: warning: declaration of 'overlay' shadows a global declaration [-Wshadow]
In file included from curses/PDCurses-3.4/curspriv.h:16:0,
from curses/PDCurses-3.4/pdcurses/overlay.c:3:
curses/PDCurses-3.4/curses.h:1014:9: warning: shadowed declaration is here [-Wshadow]
Change-Id: I907653df0c8bb32c98bdcbc6476e94d2da6e0e90
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2906
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Xinitscr is only used internally in PDCurses, unless XCURSES
is defined. This patch fixes a warning that is produced because
of that.
Change-Id: I211f75717276cf028e0b435f328d1687d3536eb7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2907
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The function dump_qh() was added a while back but never used.
Hide it behind USB_DEBUG so it doesn't cause warnings when not
debugging the USB stack.
Change-Id: Idb3c7bb214895ef82676d181836a578bf161e8e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2909
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
PDcurses is already default. Hence drop the additional attempt
that is not supported by Kconfig.
Config.in:123:warning: defaults for choice values not supported
Change-Id: I12cb5ea0bef2f146cf237c7a3cc9293a600d736b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2902
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The controller's shutdown function free()s the controller structure so
we shouldn't access it any more after calling shutdown.
As all controllers detach themself, i.e. unchain themself from usb_hcs,
just keep iterating over usb_hcs until it's NULL.
Change-Id: Ie85caba0f685494c3fe04c550a5a14bc4158a94e
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
It shouldn't be used any more as we're about to free() the memory behind
the controller -- therefore detach it.
Change-Id: I875322a9940570c51d412a7f3bfb6af4ea3b3764
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
After another incident related to virtual pointers in lib_sysinfo (and
resulting confusion), I decided to put some comments on the matter into
the code.
Remember, we decided to always use virtual pointers in lib_sysinfo, but
it's not always obvious from the code, that they are.
See also:
425973c libpayload: Always use virtual pointers in struct sysinfo_t
593f577 libpayload: Fix use of virtual pointers in sysinfo
Change-Id: I886c3b1d182cba07f1aab1667e702e2868ad4b68
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/2878
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds a test case for using CBFS images that reside in RAM
and a Makefile to run it (and maybe other tests in the future).
The test concerns an issue in libcbfs when using x86 style CBFS
images in non-canonical locations (eg. when loading CBFS images
for processing).
Use with "make run" inside the tests directory.
Change-Id: I1af3792a1451728ff9594ba7f0410027cdecb59d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2623
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change "ERROR" to "WARNING" -- not finding the indicated file is usually
not a fatal error.
Change-Id: I0600964360ee27484c393125823e833f29aaa7e7
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2833
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The template had a dependency on config.h which was correct for coreboot,
where this build system originally came from, but not for libpayload which
uses the differently named libpayload-config.h, presumably to avoid colliding
with a config.h used by the actual payload. Because libpayload-config.h is now
effectively a dependency of everything, it doesn't have to be added piecemeal
in Makefile.inc.
Change-Id: I01f20d363cb1393fa1cdcf0dc916670db90294e9
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The vboot_handoff structure needs to be parsed from the coreboot tables.
Add a placeholder in sysinfo as well as the ability to parse the
coreboot table entry concering the vboot_handoff structure.
Built with unified boot loader and ebuild changes. Can find and use
the VbInitParams for doing kernel selection.
Change-Id: If40a863b4a445fa5f7814325add03355fd0ac647
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2720
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In their current macro form, any arguments that are expressions will be
evaluated multiple times. That can cause problems if they have side effects,
and might not even compile if the overall expression is ambiguous, for
instance if you pass in foo++.
Built with code that previously wouldn't compile because the macros
expanded to ambiguous expressions.
Change-Id: I378c04d7aff5b4ad40581930ce90e49ba7df1d3e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2719
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The timekeeping code in libpayload was dependent on rdtsc, and when it was
split up by arch, that code was duplicated even though it was mostly the same.
This change factors out actually reading the count from the timer and the
speed of the timer and puts the definitions of ndelay, udelay, mdelay and
delay into generic code. Then, in x86, the timer_hz and timer_get_raw_value
functions which used to be in depthcharge were moved over to libpayload's
arch/x86/timer.c. In ARM where there isn't a single, canonical timer, those
functions are omitted with the intention that they'll be implemented by a
specific timer driver chosen elsewhere.
Change-Id: I9c919bed712ace941f417c1d58679d667b2d8269
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is static and not used in that file. To avoid the compiler
complaining about that fact, put the two functions and the call to dump_ed
(currently #if 0) behind #ifdef USB_DEBUG
Change-Id: Ic373313b5fff81f09800f286b32238350ab699c6
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
'for' loop initial declarations are only allowed in C99 mode
I didn't realize we don't enable 14 year old features when building
libpayload, and I must have accidentally not rebuilt everything when making my
final tweaks to my earlier change.
Change-Id: I6caeeffad177b6d61fa30175f767e85084c061f4
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2718
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Use memcpy to access a uint32_t that's inherently unaligned due to the layout
of the LZMA header format.
Built and booted on Daisy and saw a data abort go away. Built and booted
into developer mode on Link and verified that bitmaps were
decompressed/displayed correctly.
Change-Id: Id3ae746c04d23bcb0345cb71797bfa219479cc8f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2670
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some new TPM drivers in depthcharge require that type. I added it to
arch/types.h which seemed appropriate, but I'm not sure that's exactly the
right header to use, or in other words if you'd get that type from libpayload
the same way you'd get it if you were building a standard Linux program.
Also, I attempted to determine what underlying types gcc would use, and while
I think I picked the right ones I'm not 100% certain of that either.
Change-Id: Ic5c0b4173c8565ede3bfce8870976d596d69e51d
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2669
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Don't keep using the coreboot stack on ARMv7.
Change-Id: I734c5d77f8584e30ee0c720d41e21e3040f56db4
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2668
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: Ia85a7cd6a0b85119cce6b2f9c42a7fc31ffd9f97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2654
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EHCI controllers see transfers as a queue of transfer descriptors
(qTDs), each of which can represent an aligned area of up to 20KB. Each
qTD is processed separately, which means that a single USB packet cannot
span multiple qTDs.
While this should not be a problem according to the specification, some
USB storage devices seem to get confused when a packet in the middle of
a transfer is smaller than the maximum packet size (512 bytes) due to
falling on a qTD boundary. This patch aligns the total transfer length
per qTD to 512 bytes to avoid that problem (any excess bytes will simply
roll over to the next qTD).
Change-Id: I0b5db07507699a3861b30c1a5ee774c45dda7fdd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/2651
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Initialize the high part of the address
and use 64-bit compatible descriptors.
(waste a few bytes on 32-bit but should be harmless)
Read USB stick on a SandyBridge system which has 64-bit EHCI.
Change-Id: I59cc842459acecdde8f8bdd4795ebfeccb842c8f
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2650
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These were currently stubbed out for PowerPC but not for ARM.
Change-Id: I08f45174877bf5751d972078b8c53d82898b7f2b
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2655
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I56f810dfa6654ac1e9d1696ad15e7f1b8bfe59bd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2652
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I01b1fa42139af925716cd5d57f96dc24da6df5a7
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2660
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I36c750d520ff034c9ca9b9af46bd99bd49af7355
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2659
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This way we won't have two copies of the hardware init function, and three
copies of the putchar, havechar, and getchar functions.
Change-Id: Ifda7fec5d582244b0e163ee93ffeedeb28ce48da
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2657
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Default it to no to be consistent with the other architecture wide options
(endianness), and turn it on explicitly for x86 and PowerPC.
Change-Id: Idda26d580156bbbf08ea11b28abe75cfa6b594b2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2658
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When building other payloads with lpgcc the -nostdinc flag was injected into
CFLAGS, but when building libpayload itself some headers were being used from
the host system. This change puts -nostdinc into the Makefile and xcompile
script, fixes up one include path in include/inttypes.h, adds the compiler
provided include directory to the include search path, and deletes the two now
redundant stdint.h files.
BUG=None
TEST=With this and other changes, built libpayload and depthcharge for Daisy,
Link, and Fox.
BRANCH=None
Change-Id: Ia7817fceab5297cd82ccc0d392330de0df61980e
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2710
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There weren't enough parenthesis in the macros so operations might only apply
to the last part of an expression passed in as an argument.
Change-Id: I5afb406f9409986e45bbbc598bcbd0dd8507ed35
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2665
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I9a16331dedc97f17af94bf2cf535a9c93d1729a0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2667
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The functions in endian.h (betoh{l,w,ll} and others) were named differently from
the well-known BSD/glibc style endian functions (ex, betoh{16,32,64}). We should
provide the BSD/glibc style functions to prevent confusion.
Change-Id: Ia3bee481ba7989ac25b79ddb89bc6819d52fd8c3
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2705
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The functions defined in that header aren't used anywhere in the actual code,
and that include breaks things on ARM.
Built for ARM with COREBOOT_VIDEO_CONSOLE turned on and saw compiler
errors go away.
Change-Id: I56d6fe5e00c8fccda6e31ef8752326bd36398e74
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2656
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
That way when it's treated as a u32 when its value is extracted for numblocks
and blocksize below, it doesn't make the compiler unhappy, and it ensures that
the buffer will be properly aligned on architectures where that sort of thing
matters.
Built and saw warnings about type punning go away.
Change-Id: I254e0b5e70847112d660675b7df0ac9cb52e4051
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Three issues:
1. the hardcoded dereferenced pointer at 0xfffffffc
2. "RAM media" has no idea about ROM relative addresses
3. off-by-one in RAM media: it's legal to request 4 bytes from 0xfffffffc
Change-Id: I671ac12d412c71dc8e8e6114f2ea13f58dd99c1d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2624
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Things work better with it turned on, and the overhead should be negligable.
Built and booted into depthcharge on Snow. Verified that calling between
various bits of thumb and ARM code worked correctly.
Change-Id: I08d1006e113d2cca08634bf19240aca138a449d9
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2567
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Give some indication what happened instead of just crashing.
As part of setup, cause an exception and make sure that we get
the right one, and that we recover correctly. Hence we have
some assurance that if they really happen we can handle them.
Built and booted into test payload on Snow. Saw the built in test function
worked correctly. Artificially added code which got an exception and saw that
the error information prints correctly.
Change-Id: I2e0d022f090ee422fb988074fbb197afa2485caa
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2569
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The linker uses that info so interworking can work correctly.
Built and booted into depthcharge on Snow and saw interworking start to
work correctly.
Change-Id: I0ac54f1c424ec70f8244edf6541a10b089ce47b4
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2568
Tested-by: build bot (Jenkins)
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This function was using mdelay in a loop to check for the completion of an USB
controller operation. Since we're busy waiting anyway, we might as well wait
only 1 us before checking again and potentially seeing the completion 999 us
earlier than we would otherwise.
Change-Id: I177b303c5503a0078c608d5f945c395691d4bd8a
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2522
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This is so the user of libpayload can attach data to the device which it can
retrieve when the device is referred to later, for instance in usbdisk_remove.
Otherwise, there's no direct connection from the usbdev_t structure to any
bookkeeping in the host firmware.
Change-Id: I36fe693b0dcd2098e359c26744e376e73bd3a723
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2513
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
When checking to see if a PCI device exists at a particular bus/dev/func,
libpayload was checking the vendor and device id fields together against a 16
bit 0xffff. The two fields together are 32 bits, however, so the check was
never true, and all dev/func combinations on a particular bus would be
checked. That was slightly wasteful, but had relatively small impact.
Change-Id: Iad537295c33083243940b18e7a99af92857e1ef2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2521
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The interval used to be about 55 ms which is excessively long. Coreboot only
waits for 2 ms and gets a reasonable answer. That should be good enough for us
as well.
Change-Id: I4d4e8b25b6ba540c9e9839ed0bbaa1f04f67cce1
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2520
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Cherry-picking CBFS fix from http://review.coreboot.org/#/c/2292/
For x86, the old CBFS search behavior was to bypass bootblock and we should keep
that. This will speed up searching if a file does not exist in CBFS.
For arm, the size in header is correct now so we can remove the hack by
CONFIG_ROM_SIZE.
Change-Id: I286ecda73bd781550e03b0b817ed3fb567d6b8d7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2458
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Not only were these files checked in with the Chromium OS Authors
copyright, but in addition they were wrongly licensed as GPL.
Switch to 3-clause BSD (and, since we're changing it, fix copyright,
too)
Change-Id: I3656c1f4304d53e343d89bb7c909fd4b929249f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2456
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
get_cbfs_header expects CBFS_HEADER_INVALID_ADDRESS (0xffffffff)
instead of NULL when something is wrong.
Also, fix typo.
Change-Id: Ibe56c9eab3b9fdfc6d0b14bc848ca75f3a4fc2f1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2455
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Create a new serial console variable, X86_SERIAL_CONSOLE
which is only enabled when SERIAL_CONSOLE and ARCH_X86 are defined.
Builds for x86 and ARM.
Change-Id: I607253c418de015975a839e3c33577842885ec0c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2412
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
The compiler gets mad when the types are equivalent size but not necessarily
interchangeable because of strict aliasing checks. Since uint32_t is likely to
be used when trying to read 32 bit data, it makes sense for them to be the
compatible.
Signed-off-by: Gabe Black <gabeblack@google.com>
Change-Id: If73d794866055dc026fc06d6268e692adac0f835
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2411
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
lpgcc was unconditionally setting -m32.
Most of the flags it sets in the common case are right, however: no need
to duplicate them everywhere, and we only want to change the common ones
in one place, so it would be a shame to duplicate _CFLAGS all over the place.
So add another variable, _ARCHEXTRA, which can be used to add
special flags to _CFLAGS. We onlu use it at present for the x86; this may
change.
This allows us to get through compiling on arm and x86.
Change-Id: I12f1620982c4ee10f76b3953e4225f13db31531e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2399
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Get rid of the nest of includes, and make separate sections
for each architecture. Also gets rid of the "there's X86 and there's
everything else" structure of this file.
Change-Id: I4232f50f048fa05e911e5de3aa9ec1530931b461
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2397
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
The default_ functions in memory.c are only used to initialize a weak
variable. They should not be used outside memory.c. Make them
invisible.
Remove the declaration from libpayload.h. For real this time.
Change-Id: Id54c1fd172c78748f01a958ce4065dd0eb53bbc3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2394
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
These live at the bottom of memory on x86, but that's IO mapped on the exynos.
The particular range used will likely need to be configurable, but this will
make it work in one more case than it used to.
Change-Id: I4d4963b9732cf538d00f8effb4398f30cbbde6aa
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2410
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
I think this needs to be its own ldscript. I'm pretty sure this one
is going to need some work however. Is libpayload PIC? That would be
best if so.
Change-Id: I44578d70dfa72de527af8901a86583c2a60130ec
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2398
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Since it's utterly architecture-dependent, put it in arch/x86.
Avoid the temptation to make yet another directory with just one
file in it. Fix the makefile to pick up the proper arch-dependent script.
Change-Id: I21ea02551a97bdcbc38419714f3b38cf8335c178
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2389
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Upgrade CBFS in libpayload to use new media-based implementation from coreboot
( http://review.coreboot.org/#/c/2182/ ).
Old CBFS functions (cbfs_find, cbfs_find_file, get_cbfs_header) are still
supported, although the recommended way is to use new CBFS API.
To migrate your existing x86 payload source:
- Change cbfs_find to cbfs_get_file
- Change cbfs_find_file to cbfs_get_file_content
- Prefix every CBFS call with a CBFS_DEFAULT_MEDIA argument.
Ex, char *jpeg_data = cbfs_find_file("splash.jpg", CBFS_TYPE_BOOTSPLASH);
=> char *jpeg_data = cbfs_get_file_content(
CBFS_DEFAULT_MEDIA, "splash.jpg", CBFS_TYPE_BOOTSPLASH);
The legacy setup_cbfs_from_{ram,flash} is also supported, although the better
equivalent is to make a new media instance:
struct cbfs_media ram_media;
init_cbfs_ram_media(&ram_media, start, size);
char *data = cbfs_get_file_content(&ram_media, "myfile", my_type);
Verified by being successfully linked with filo.
Change-Id: If797bc7e3ba975d7e3be905c59424f7a93b8ce11
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2191
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The libpaylaod xcompile script path to xgcc should look
for coreboot/util, not libpayload/util.
Change-Id: I565801549cdcdfcf55ecef1b543a982f969f435b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2261
Tested-by: build bot (Jenkins)
Reviewed-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Improve USB debugging for EHCI by adding dump_qh
and enhacing dump_td to dump all queue chain and information.
Change-Id: Ia8ecf19c6dac085cf9558bdf659a5e74ce332714
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2053
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
When overriding the DOTCONFIG variable, make install
will fail in libpayload.
Change-Id: I332be3a4ca2620a32a6f5fbe683e6c71f0d6a9e9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2178
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The 'VERSION' in CBFS header file is confusing and may conflict when being used
in libpayload.
Change-Id: I24cce0cd73540e38d96f222df0a65414b16f6260
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2098
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
A "far" modifier sneaked into the USB driver, but gcc
doesn't understand it.
Change-Id: I5c67bd55eabce467e1aa107c95c1db2518af7b0e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2059
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Improved USB debugging for EHCI by enhacing dump_td
to dump all chain information
Change-Id: I8c667b43e09c39ff12aafbd779474efd652bd80f
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2054
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Improving USB debugging for OHCI by enhacing dump_td
and adding dump_ed function to dump all chain information
Change-Id: Ia8b2a9b53e79b1f280fd12ea0d9233fc875e0b57
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2056
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
The serial_io_havechar() and serial_io_getchar() functions will
always see keystrokes available if the serial hardware isn't
actually there. We will still output chars to non-existant
hardware to allow virtual hardware to capture them.
Change-Id: I04e85157b6b7a185448abab352b5417a798a397a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2040
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Previously printf()'s were used to show USB messages
which results in lots of USB information being shown
when it isn't needed. This will now use the usb_debug()
printing funtion that already exists in usb.h.
Change-Id: I2199814de3327417417eb2e26a660f4a5557cb9f
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2044
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Several settings have been added to the config without any
changes to the default settings file.
Change-Id: Iaf9259d77fb3c4645fc68bc0108de79c0298f0a1
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2039
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This implements the linux kernel's macros to handle
boolean CONFIG_ variables more easily.
Change-Id: I595f9db652d019fe72e231111258ec609bec9d4e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2036
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This compiles, but it's not tested yet.
Change-Id: I2f73a814649aa36c39af3e77cefd8a968671f5c0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2035
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Coreinfo uses the default heap size and will blow up
if the USB keyboard is used.
Change-Id: I2ffae330ec34167b2ccfbd4c428e3e8306230f44
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1980
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
In I4c456f5, I falsely identified struct cb_string.string as a pointer
which it is not. So we don't need phys_to_virt() here.
Change-Id: I3e2b6226ae2b0672dfc6e0fa4f6990e14e1b7089
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1987
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
lpgcc and lpas are called by payload Makefiles to properly
build and link with libpayload.
Made lpas use the proper crosscompile AS, as lpgcc does with CC.
Added V=1 support to help users debug the build.
Fix basename $CC and $AS expansion.
Change-Id: Ia4dc8ba53ba7565521a79f1520155f3307b09f85
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1993
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This renames TARGET_I386 to ARCH_X86 to make it more uniform with
other parts of the codebase, e.g. cbfs_core.h from cbfstool.
Change-Id: I1babcc941245ed1dde0478a21828766759373a42
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1961
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
This bug was introduced when we copied cbfs_core.h from cbfsutil
to libpayload.
Change-Id: I9b5d00d0dbdb969644ce46ad6ac2a84b366b5cd7
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1958
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
The FLAG_USED bit in the memory allocator's header type was never
read. This removes it to save one bit for the region size so we can
have heaps of up to 32MiB.
Change-Id: Ibd78e67d79e872d6df426516667c795fd52326d5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1942
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The condition to compare the labels was twisted.
Change-Id: I34a665aa87e2ff0480eda0f249bbbea8a8fe68d8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1941
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is an initial re-factoring of CBFS code to enable multiple
architectures. To achieve a clean solution, an additional field
describing the architecture has to be added to the master header.
Hence we also increase the version number in the master header.
Change-Id: Icda681673221f8c27efbc46f16c2c5682b16a265
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1944
Tested-by: build bot (Jenkins)
Slightly more complete keymap
Change-Id: I4fef6b8f75ab07cb20a3a8ccd7eaad81c9fe719f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1922
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We have to free TDs more carefully if they have been processed by the
controller yet. The current code tries to force the controller to post
them back to the done queue, but that seems wrong. We can't be sure,
when they get written back. This resulted in leaking TDs with an invalid
reference to a freed interrupt queue.
The new approach: Mark the interrupt queue to be destroyed and handle
the freeing later, when the controller posted the last TD to the done
queue.
Change-Id: I79d80a9dc89e1ca79dc125c4bbccbf23664227b3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1905
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The connection state detection in the OHCI root hub driver was broken if
you used more than one device per root hub.
Change-Id: Ica5c735426beac45ef6f591ce68a72d8283a00f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1904
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
If somethings goes wrong during an interrupt transfer, drop the
transfer.
Change-Id: I450c08a7a0bf23fbee74237e0355d4a726ace114
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1901
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
If usb_poll() isn't called fast enough, the UHCI controller marks an
underrun interrupt queue as done (terminating the queue at the head).
We can recover from this situation, when usb_poll() gets called again,
and the queue is processed.
Change-Id: Id56c9df44d6dbd53cd30ad89dfb5bf5977799829
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1898
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The linking of interrupt queues into UHCI controller's framelist (in
uhci_create_intr_queue()) was incomplete. The implementation of
uhci_destroy_intr_queue() was even worse, looking like it wanted to
clean up more than uhci_create_intr_queue() did.
This patch follows the simple approach that we used for OHCI and EHCI:
Each slot in the framelist holds only one interrupt queue. Therefore, we
have to look for free slots each time we want to link an interrupt queue
into the framelist. In return, we have a much simpler structured
framelist.
With this, USB devices using interrupt transfers (e.g. keyboards) can be
detached cleanly from UHCI controllers. Also, more than one of such
devices can be attached without further risk.
Change-Id: I07b81a3b6f2cb3ff69515c973b3ae6321ad969aa
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1897
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The USB HID driver had some static variables with keyboard state. This
moves them to the driver's instance, so multiple attached keyboards
don't effect each other.
Change-Id: I3f1ccfdea95062b443cebe510abf2f72fdeb1916
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1907
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Prevent race conditions, when an interrupt-queue underrun occurred and
the controller is currently working on our queue head or a transfer is
still in progress.
Change-Id: Ia14f80a08071306ee5d1349780be081bfacb206a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1902
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
When a USB hub got removed, we should also remove all devices that
were attached to it.
Change-Id: I73c0da1b7570f1af9726925ca222781b3d752557
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1903
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
If an endpoint gets stalled by an MSC device, after successful
transmission of a command (CBW), we should still ask for the status
(CSW). Otherwise, the driver and the device get desynchronized on the
command tags.
Change-Id: I53167f22c43b3a237cb4539b3affe37799378b93
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1900
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Stalled transfers are not fatal, so don't spew on the console on every
tiny failure.
Change-Id: I175c1e83a6af09c1abbd43d045ed6dbf0c79f871
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1899
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
dump_td() is orphaned but looks useful => commented out.
The delay identifier shadowed the global one => renamed to total_delay.
Change-Id: I4f3766a07db9194b2552ebf9302bd7ef8a66371f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1895
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
We can trust free() and memset() to work correctly on volatile
references, so cast volatile pointers to (void *) when calling them.
Change-Id: Ieff7f78133b72f303349cca0a0ca3bbf37ec52bb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1896
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
usb_controller_initialize() is not declared in any header file nor
called from outside of usbinit.c, so make it static.
set_configuration() looks like beeing non-static on purpose (like the
other helpers around it in usb.c), so put a prototype into usb.h.
Change-Id: I08d93b3769d8398bb43462d9afdfeec81fef93ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1894
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Found a bug in the memory allocator ;-)
If the total free space in an alignment region is large enough for an
allocation but fragmented, such that there is no contiguous, sufficient
large, free space in the region, memalign() was looking at the same
region again and again in an endless loop. The advancing to the next
region was just missing.
Change-Id: I3fad833804675ee495577ca2749b007f46b5ff69
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1906
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
We had mixed virtual and physical pointers in struct sysinfo_t. Some
being virtual by accident which led to problems when we tried to
reinitialize lib_sysinfo after relocating FILO (to get intentionally
virtual pointers valid again). I guess this didn't cause much trouble
before, as lib_get_sysinfo() was always called with physical addresses
being equal to their virtual counterparts.
For FILO, two possibilities seem practical: Either, have all pointers in
struct sysinfo_t physical, so relocation doesn't hurt. Or, have all
pointers virtual and call lib_get_sysinfo() again after relocation.
This patch goes the latter way, changing the following pointers for
situations where virtual pointers differ from physical:
.extra_version
.build
.compile_time
.compile_by
.compile_host
.compile_domain
.compiler
.linker
.assembler
.cb_version
.vdat_addr
.tstamp_table
.cbmem_cons
.mrc_cache
We could also just correct the accidentally virtual pointers. But, IMO,
this would lower the risk of future confusion.
Note 1: Looks like .version gets never set.
Note 2: .option_table and .framebuffer were virtual pointers but treated
like physical ones. Even in FILO, this led to no problems as
they were set before relocation.
Change-Id: I4c456f56f049d9f8fc40e62520b1d8ec3dad48f8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1855
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Libpayload uses the linux kernel's config style, where CONFIG_* defines
don't get written for unset tristates.
Change-Id: I3f832cf86bca9a1e153d96af4bf6434a19eba2f6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1847
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
uhci_reset() differs in semantics compared to the other HCI's reset()
implementations. uhci_reset() does some initialization work after a
controller reset. So move the initialization part to a new function,
uhci_reinit(), which get's exported through a new entry in hci_t:
hci_t.init().
Warning: This breaks code that relies on the current, special,
counterintuitive behaviour of uhci_reset(). If one wants a working host
controller after calling hci_t.reset(), he should call hci_t.init()
afterwards.
Change-Id: Ia7ce80865d12d11157645ce251f77f349f8e3c34
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When ohci_reset() was implemented, OHCI controllers stopped working
since the stub ohci_reset() is called at the end of ohci_init().
This is fixed by removing the call. To prevent further problems the call
to the xhci_reset() stub is removed, too.
Change-Id: If89825c8e6caf40f7f4fe078e8b2e90054a54ba2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All shutdown() implementations but ehci_shutdown() free the hci_t
structure. This seems correct and the reference to the hci_t shouldn't
be used after shutdown(), so do it in ehci_shutdown(), too.
Change-Id: Ie3506d769e73007735f3211710734a5f0107e43a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1849
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The semantics of the controller functions, start(), stop(), reset() and
shutdown(), are not self-explanatory which let to some confusion. At
least the reset() functions of the different host controller drivers
were implemented following different interpretations. Let's make the
intended behaviour of these functions clear.
The stated inconsistencies will be addressed in following commits.
Change-Id: Id2e300f65c21039218b6ba3f87c0fcd4f0dda0a8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1848
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
David Hendricks