This patch addresses different argument order of outX() calls,
FreeBSD-specific headers, difference in certain type names and system
interface names, and also FreeBSD-specific way of gaining IO port
access.
Signed-off-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The PMC chips understand both LPC and FWH flash commands. When in FWH mode
(MSR_DIVIL_BALL_OPT(0x51400015) = 0x00000f7d on 5536 boards) the Block
Locking Registers by default lock the flash chip for write and erase - in
addition to any chipset write protection.
This patch adds unlock operations before Pm49FL004/2 write and erase, and
it includes an svn mv pm49fl004.c pm49fl00x.c
Thanks go to Nikolay for this patch.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips.c, but the IDs in flash.h will make lookups easier if anybody
wants to add support for them.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3321 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Powerdown) SPI command to flashrom to identify older SPI chips which
can't handle JEDEC RDID. Since RES gives a one-byte identifier which is
shared among many different vendors and even different sizes, we want to
match RES as a last resort if RDID returns 0xff 0xff 0xff.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
This is a heavily reworked version of a patch by Fredrik Tolf, which was
Signed-off-by: Fredrik Tolf <fredrik@dolda2000.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3320 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
detected by JEDEC probe routines all have vendor IDs with correct
parity. Use a parity check as additional hint whether a vendor ID makes
sense.
Note: Device IDs have no parity requirements whatsoever.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3308 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by Harald Gutmann.
SST39VF040 has been confirmed to probe OK by misi e.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3300 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
series has the same IDs.
Add short AMIC vendor ID to flashrom.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a very early step toward cleaning up SPI code in flashrom.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3295 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Two bits indicate OK and BAD for each operation PROBE READ ERASE WRITE.
8 bits out of 32 are in use now. No bits set means nothing has been tested.
For chips with at least one operation that is not tested or not working, the
user is asked to email a report to a special email adress so that the table
can be updated.
All chips are TEST_UNTESTED for now.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3277 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
devices, because they need an unlock command first.
For this reason, ST M50FLW support is moved to a
new HW support module, because any change in jedec.c
would bear the risk to cause problems with the already
supported devices.
It's already tested with ST M50FLW080A; the other
chips of this family i dont have available, so i couldnt
test it.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Cosmetic changes in some files, partly bending the 80-characters-per-line
rule in this special case, as the 80-character-limited version looks
equally crappy even in an 80x25 console/xterm, so let's make it at least
look good in a high-resolution xterm.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3139 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Programmable Micro Corp (PMC) need this.
Both the serial and parallel flash JEDEC detection routines would
benefit from a parity/sanity check of the vendor ID. Will do this later.
Add support for the PMC Pm25LV family of SPI flash chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
exactly the same ID. Improve model number printing.
Add EN29F002(A)(N)B support while I'm at it.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(JEP106W), adds some device IDs and provides information about
non-conforming IDs.
The EON change is left to the patch adding EON chips.
This patch should have no effect on code generation.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add support for the Fujitsu MBM29F400TC flash part.
Detection and reading works, writing is not tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.
So I created a very quick patch (attached).
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2897 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip the code was tested and verified with is the Macronix MX25L4005,
but other chips should work as well.
Timeouts are still hardcoded to data sheet maxima, but the status
register checking code is already there.
Thanks to Harald Gutmann for the initial code on which this is loosely
based.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2857 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
way. It introduces a generic SPI host driver for the IT8716F Super I/O
which will enable easy SPI programming without having to care for the
peculiarities of the SPI host.
To activate probing for the IT8716F, you have to use the gigabyte:m57sli
mainboard override. SPI support will then use the gathered SPI host data
to access the SPI flash.
This has been tested sucessfully by Ward Vandewege <ward@gnu.org> on the
GA-M57SLI v2.0, which has a MX25L4005 SPI flash part.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M50FLW080B, M50FW080, M50FW016, M50LPW116, M29W010B flash chips made
by ST to flashrom.
The patch is based on the data sheets of the chips and has not been
tested at all.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only reading from the chips was tested; writing support is untested.
Thanks to Gürkan Sengün <gurkan@linuks.mine.nu> for testing!
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf Marek