Now that the console system itself will clearly differentiate loglevels,
it is no longer necessary to explicitly add "ERROR: " in front of every
BIOS_ERR message to help it stand out more (and allow automated tooling
to grep for it). Removing all these extra .rodata characters should save
us a nice little amount of binary size.
This patch was created by running
find src/ -type f -exec perl -0777 -pi -e 's/printk\(\s*BIOS_ERR,\s*"ERROR: /printk\(BIOS_ERR, "/gi' '{}' ';'
and doing some cursory review/cleanup on the result. Then doing the same
thing for BIOS_WARN with
's/printk\(\s*BIOS_WARNING,\s*"WARN(ING)?: /printk\(BIOS_WARNING, "/gi'
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3d0573acb23d2df53db6813cb1a5fc31b5357db8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Lance Zhao
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
In order to provide the same loglevel prefixes and highlighting that
were recently introduced for "interactive" consoles (e.g. UART) to
"stored" consoles (e.g. CBMEM) but minimize the amont of extra storage
space wasted on this info, this patch will write a 1-byte control
character marker indicating the loglevel to the start of every line
logged in those consoles. The `cbmem` utility will then interpret those
markers and translate them back into loglevel prefixes and escape
sequences as needed.
Since coreboot and userspace log readers aren't always in sync,
occasionally an older reader may come across these markers and not know
how to interpret them... but that should usually be fine, as the range
chosen contains non-printable ASCII characters that normally have no
effect on the terminal. At worst the outdated reader would display one
garbled character at the start of every line which isn't that bad.
(Older versions of the `cbmem` utility will translate non-printable
characters into `?` question marks.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I86073f48aaf1e0a58e97676fb80e2475ec418ffc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Chromebooks normally run with non-serial enabled firmware because
writing to the UART console is very slow. This unfortunately makes
debugging boot errors more difficult. We tend to rely on port 80s and/or
the vboot recovery code.
When CONSOLE_CBMEM_DUMP_TO_UART is selected it will dump the entire
cbmem console to the UART whenever `vboot_reboot()` is called. We don't
incur any boot time penalty in the happy path, but still retain the
ability to access the logs when an error occurs.
The previous implementation was using a hard coded UART index and
`get_uart_baudrate` was always returning 0 since `CONFIG_TTYS0_BAUD`
wasn't defined. This change makes it so the UART console properties are
available when CONSOLE_CBMEM_DUMP_TO_UART is set. This results in the
following .config diff:
+CONFIG_UART_FOR_CONSOLE=0
+CONFIG_TTYS0_BASE=0x3f8
+CONFIG_TTYS0_LCS=3
+CONFIG_CONSOLE_SERIAL_115200=y
+CONFIG_TTYS0_BAUD=115200
This functionality is especially helpful on Guybrush. PSP Verstage is
run on S0i3 resume. Today, if there is an error, the cbmem console is
lost since it lives in the PSP SRAM.
BUG=b:213828947, b:215599230
TEST=Build non-serial guybrush FW and verify no serial output happens in
happy path. Inject a vboot error and perform an S0i3 suspend/resume.
Verify CBMEM console gets dumped to the correct UART.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I997942204603362e51876a9ae25e493fe527437b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Building libgfxinit with Debian’s toolchain – latest test with *gnat-11*
11.2.0-13 from Debian sid/unstable – the build fails with the error
below.
E: Invalid reloc type: 10
E: Unable to create rmodule from 'build/cbfs/fallback/ramstage.debug'.
Debian’s toolchain is built without enabling PIE by default.
So, explicitly pass `-fno-pie` to `ADAFLAGS_common` to be independent
from how the toolchain was built.
TEST=*gnat* 11.2.0-13 successfully. builds
purism/librem_cnl/variants/librem_mini with libgfxint.
With the coreboot toolchain `make BUILD_TIMELESS=1` produces the
same `build/coreboot.rom` for `BOARD_PURISM_LIBREM_MINI_V2=y` on
top of commit 50251400d2 (sb/intel/common/firmware: Reword
me_cleaner warning) with and without the change.
Change-Id: I6661937906d95c130c6099f598d61b21e958fd85
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
When running in verstage before bootblock, the PSP (ARM co-processor) is
running with limited SRAM. It needs to stash the verstage console data
internally until DRAM is brought up. Once DRAM is brought up the data is
stashed in a "transfer buffer" region. In the current design, we are
using the same region for the transfer buffer and the
preram_cbmem_console region. This has the following downsides:
1) The pre-x86 buffer needs to be large enough to hold all the
verstage, bootblock and romstage console logs.
2) On AMD platforms, the PSP verstage is signed. Changing the size of
preram_cbmem_console after the fact will result in a mismatch of the
transfer buffer between verstage and bootblock.
This CL adds a new method that allows SoC specific code to copy the
CBMEM console in the transfer buffer to the active CBMEM console.
BUG=b:213828947
TEST=Boot guybrush and no longer see
*** Pre-CBMEM romstage console overflowed, log truncated!
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idc0ab8090db740e0d1b3d21d8968f26471f2e930
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Change timestamp_add to accept negative values for events that took
place before coreboot started executing.
TEST=Boot to OS, check cbmem -t
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I90afc13a8e92693d86e3358f05e0a0cb7cdbca9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 6a3bdf9aa5.
Reason for revert: Oops, I thought I abandoned this. It's been replaced by https://review.coreboot.org/c/coreboot/+/61099/3
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id18e8e69481bdd78fdd70116940ea435922a9e77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This will make the method available earlier. This is needed for the next
CL.
BUG=b:213828947
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iee911a2debcfbf4309d2e866401b74f2a6c18feb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This function is similar to cbmem_dump_console_to_uart except it uses
the normally configured consoles. A console_paused flag was added to
prevent the cbmem console from writing to itself.
BUG=b:213828947
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3fe0f666e2e15c88b4568377923ad447c3ecf27e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This function actually dumps cbmem to the UART. This change renames the
function to make that clear.
BUG=b:213828947
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Icc314c530125e5303a06b92aab48c1e1122fd18c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
<rules.h> and <commonlib/bsd/compiler.h> are always automatically
included in all compilation units by the build system
Change-Id: I9528c47f4b7cd22c5a56d6a59b3bfe53197cc4d8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Remove chromeos_dsdt_generator() calls under mainboard, it
is possible to make the single call to fill \CNVS and
\OIPG without leveraging device operations.
Change-Id: Id79af96bb6c038d273ac9c4afc723437fc1f3fc9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Because of a typo, `bootblcok-y += rtc.c` does nothing. Drop it.
Change-Id: Ife2ee152ab32ef23df5986c47bec490db592ab60
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56216
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Preloading files before vboot runs and using them after vboot has
finished will result in the wrong files getting used. Disable
cbfs_preload to avoid this behavior.
BUG=b:179699789
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7698b481a73fb24eecf4c810ff8be8b6826528ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This change consolidates the COOP rules. Co-op in theory works in all
x86 stages now, but it hasn't been enabled yet.
BUG=b:179699789
TEST=Boot guybrush to OS and verify preloads still work
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1197406d1d36391998b08e3076146bb2fff59d00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With the elimination of remaining non-verifying CBFS APIs in CB:59682,
CBFS verification is now ready to be used in its simplest form, so
enable the respective Kconfig options in menuconfig. Add a few more
restrictions to the TOCTOU_SAFETY option for problems that haven't been
solved yet, and transform a comment in cbfs.c into a die() to make sure
we don't accidentally forget implementing it once vboot integration gets
added.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ifeba5c962c943856ab79bc6c4cb90a60c1de4a60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
This patch removes all remaining pieces of the old CBFS API, now that
the last straggling use cases of it have been ported to the new one
(meaning cbfs_map()/cbfs_load()/etc... see CB:39304 and CB:38421).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1cec0ca2d9d311626a087318d1d78163243bfc3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch moves the CBFS file measurement when CONFIG_TPM_MEASURED_BOOT
is enabled from the lookup step into the code where a file is actually
loaded or mapped from flash. This has the advantage that CBFS routines
which just look up a file to inspect its metadata (e.g. cbfs_get_size())
do not cause the file to be measured twice. It also removes the existing
inefficiency that files are loaded twice when measurement is enabled
(once to measure and then again when they are used). When CBFS
verification is enabled and uses the same hash algorithm as the TPM, we
are even able to only hash the file a single time and use the result for
both purposes.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I70d7066c6768195077f083c7ffdfa30d9182b2b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The 'at' part of the name refers to starting to read from a specific
offset, so it doesn't make sense for the 'full' version of the function.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I60d595f0cbd161df171eaa4a76c7a00b6377e2b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59820
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a new ..._unverified_area_... group of functions to the
cbfs_map/_load/_alloc() APIs. These functions can be used to access
custom FMAP sections and are meant to replace the existing
cbfs_locate_file_in_region(). The name is intended to highlight that
accesses through this API will not be verified when CBFS_VERIFICATION is
enabled and should always be treated as if they may return malicious
data. (Due to laziness I'm not adding the combination of this API with
the ..._type_... variant at this point, since it seems very unlikely
that we'll ever have a use case for that. If we ever do, it should be
easy to add later.)
(Also remove the 'inline' from cbfs_file_hash_mismatch(). I'm not sure
why I put it there in the first place, probably a bad copy&paste.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I402265900f7075aa0c2f58d812c67ea63ddf2900
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch adds cbfs_get_size() and cbfs_get_type() helper functions
(and _ro_ variations) to look up the size or type of a CBFS file without
loading it. Generally, use of these should be discouraged because that
tends to mean that the file needs to be looked up more than once, and
cbfs_alloc() or cbfs_type_load() are usually the more efficient
alternative... but sometimes they're unavoidable, so we might as well
offer them.
Also remove the <cbfs_private.h> header which had already become sort of
unnecessary with previous changes. cbfs_boot_lookup() is now exported in
<cbfs.h> for use in inlines, but should not be used directly by other
files (and is prefixed with an underscore to highlight that).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8092d8f6e04bdfb4df6c626dc7d42b402fe0a8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
This will enable preloading ramstage. By preloading the file into
cbfs_cache we reduce boot time.
BUG=b:179699789
TEST=Boot guybrush to OS and see 12ms reduction in boot time.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ibe12de806449da25bc0033b02fcb97c3384eddc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Now that CBFS has this functionality built in, we no longer need to
manually code it.
payload_preload used to use the payload_preload_cache region to store
the raw payload contents. This region was placed outside the firmware
reserved region, so it was available for use by the OS. This was
possible because the payload isn't loaded again on S3 resume.
cbfs_preload only uses the cbfs_cache region. This region must be
reserved because it gets used on the S3 resume path. Unfortunately this
means that cbfs_cache must be increased to hold the payload. Cezanne is
the only platform currently using payload_preload, and the size of
cbfs_cache has already been adjusted.
In the future we could look into adding an option to cbfs_preload that
would allow it to use a different memory pool for the cache allocation.
BUG=b:179699789
TEST=Boot guybrush and verify preloading the payload was successful
CBFS DEBUG: get_preload_rdev(name='fallback/payload') preload successful
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idc521b238620ff52b8ba481cd3c10e5c4f1394bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change makes it so the timers run after each boot state callback,
and after each boot state. This gives coop threads the opportunity to
run more frequently and predictably.
BUG=b:179699789
TEST=Boot guybrush to OS, see SPI transactions progress faster.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9508e7777d52fe934cc09d486abc0dab5cf7dad8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
List of changes:
1. Create Module Type macros as per Memory Type
(i.e. DDR2/DDR3/DDR4/DDR5/LPDDR4/LPDDR5) and fix compilation
issue due to renaming of existing macros due to scoping the Memory
Type.
2. Use dedicated Memory Type and Module type for `Form Factor`
and `TypeDetail` conversion using `get_spd_info()` function.
3. Create a new API (convert_form_factor_to_module_type()) for
`Form Factor` to 'Module type' conversion as per `Memory Type`.
4. Add new argument as `Memory Type` to
smbios_form_factor_to_spd_mod_type() so that it can internally
call convert_form_factor_to_module_type() for `Module Type`
conversion.
5. Update `test_smbios_form_factor_to_spd_mod_type()` to
accommodate different memory types.
6. Skip fixed module type to form factor conversion using DDR2 SPD4
specification (inside dimm_info_fill()).
Refer to datasheet SPD4.1.2.M-1 for LPDDRx and SPD4.1.2.L-3 for DDRx.
BUG=b:194659789
TEST=Refer to dmidecode -t 17 output as below:
Without this code change:
Handle 0x0012, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: Not Provided
Total Width: 16 bits
Data Width: 16 bits
Size: 2048 MB
Form Factor: Unknown
....
With this code change:
Handle 0x0012, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: Not Provided
Total Width: 16 bits
Data Width: 16 bits
Size: 2048 MB
Form Factor: Row Of Chips
....
Change-Id: Ia337ac8f50b61ae78d86a07c7a86aa9c248bad50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
We are currently counting how long it takes to print the waiting
message, in addition to the actual time we spent waiting. This results
in inflating the measurement by 1.7ms when the serial console is
enabled. This CL makes it so the print happens before the stopwatch
starts.
BUG=b:179699789
TEST=No longer see printk time taken into account on serial console
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib48e37c1b2cb462d634141bf767673936aa2dd26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Currently, the MMCONF Kconfigs only support the Enhanced Configuration
Access mechanism (ECAM) method for accessing the PCI config address
space. Some platforms have a different way of mapping the PCI config
space to memory. This patch renames the following configs to
make it clear that these configs are ECAM-specific:
- NO_MMCONF_SUPPORT --> NO_ECAM_MMCONF_SUPPORT
- MMCONF_SUPPORT --> ECAM_MMCONF_SUPPORT
- MMCONF_BASE_ADDRESS --> ECAM_MMCONF_BASE_ADDRESS
- MMCONF_BUS_NUMBER --> ECAM_MMCONF_BUS_NUMBER
- MMCONF_LENGTH --> ECAM_MMCONF_LENGTH
Please refer to CB:57861 "Proposed coreboot Changes" for more
details.
BUG=b:181098581
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_KOHAKU -x -a -c max
Make sure Jenkins verifies that builds on other boards
Change-Id: I1e196a1ed52d131a71f00cba1d93a23e54aca3e2
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Read fw_config value from VPD.
This new option can be used where chrome EC is not supported like
pre-silicon platform and fw_config can be updated by VPD tool in OS.
TEST= boot to OS and read fw_config from vpd
1. Boot to OS
2. Write "fw_config" in VPD
ex) vpd -i "RW_VPD" -s "fw_config"="1"
3. reboot and check fw_config value from coreboot log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I4df7d5612e18957416a40ab854fa63c8b11b4216
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Request fw_config values from various sources (as enabled via Kconfig)
until a valid value has been read.
With this change, Chrome EC CBI takes precedence over CBFS fw_config.
TEST=select both configs and check fallback behavior.
1. select both FW_CONFIG_SOURCE_CHROMEEC_CBI and FW_CONFIG_SOURCE_CBFS
2. check log for reading fw_config from CBI and CBFS
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I215c13a4fcb9dc3b94f73c770e704d4e353e9cff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This API will hide all the complexity of preloading a CBFS file. It
makes it so the callers simply specify the file to preload and CBFS
takes care of the rest. It will start a new thread to read the file into
the cbfs_cache. When the file is actually required (i.e., cbfs_load,
etc) it will wait for the preload thread to complete (if it hasn't
already) and perform verification/decompression using the preloaded
buffer. This design allows decompression/verification to happen in the
main BSP thread so that timestamps are correctly reflected.
BUG=b:179699789
TEST=Test with whole CL chain, verify VGA bios was preloaded and boot
time was reduced by 12ms.
Logs:
Preloading VGA ROM
CBFS DEBUG: _cbfs_preload(name='pci1002,1638.rom', force_ro=false)
CBFS: Found 'pci1002,1638.rom' @0x20ac40 size 0xd800 in mcache @0xcb7dd0f0
spi_dma_readat_dma: start: dest: 0x021c0000, source: 0x51cc80, size: 55296
took 0 us to acquire mutex
start_spi_dma_transaction: dest: 0x021c0000, source: 0x51cc80, remaining: 55296
...
spi_dma_readat_dma: end: dest: 0x021c0000, source: 0x51cc80, remaining: 0
...
CBFS DEBUG: _cbfs_alloc(name='pci1002,1638.rom', alloc=0x00000000(0x00000000), force_ro=false, type=-1)
CBFS: Found 'pci1002,1638.rom' @0x20ac40 size 0xd800 in mcache @0xcb7dd0f0
waiting for thread
took 0 us
CBFS DEBUG: get_preload_rdev(name='pci1002,1638.rom', force_ro=false) preload successful
In CBFS, ROM address for PCI: 03:00.0 = 0x021c0000
PCI expansion ROM, signature 0xaa55, INIT size 0xd800, data ptr 0x01b0
PCI ROM image, vendor ID 1002, device ID 1638,
PCI ROM image, Class Code 030000, Code Type 00
Copying VGA ROM Image from 0x021c0000 to 0xc0000, 0xd800 bytes
$ cbmem
...
40:device configuration 5,399,404 (8,575)
65:Option ROM initialization 5,403,474 (4,070)
66:Option ROM copy done 5,403,488 (14)
...
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I879fc1316f97417a4b82483d353abdbd02b98a31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This cleans up the warning message:
WARNING: Prefer using '"%s...", __func__' to using 'thread_run', this function's name, in a string
BUG=b:179699789
TEST=boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I85bacb7b2d9ebec40b6b05edc2ecf0ca1fc8ceee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This makes it easier to grep for errors.
BUG=b:179699789
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7eecdfed6046b7d609069e7427f6883a4e9e521d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This will be used in cbfs.c which is used in all stages.
BUG=b:179699789
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0713ae766c0ac9e43de702690ad0ba961d636d18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
AMD platforms require the destination to be 64 byte aligned in order to
use the SPI DMA controller. This is enforced by the destination address
register because the first 6 bits are marked as reserved.
This change adds an option to the mem_pool so the alignment can be
configured.
BUG=b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8d77ffe4411f86c54450305320c9f52ab41a3075
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56580
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This method will add a node to the end of the list.
BUG=b:179699789
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1792e40f789e3ef16ceca65ce4cae946e08583d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add backlight support in ps8640 through the AUX channel using eDP
DPCD registers.
BUG=b:202966352
BRANCH=trogdor
TEST=verified firmware screen works on homestar rev4
Change-Id: Ief1bf56c89c8215427dcbddfc67e8bcd4c3607d2
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add DDR5 and LPDDR5 memory type checks while calculating bus width
extension (in bits).
Additionally, update all caller functions of
smbios_bus_width_to_spd_width() to pass `MemoryType` as argument.
Update `test_smbios_bus_width_to_spd_width()` to accommodate
different memory types.
Create new macro to fix incorrect bus width reporting
on platform with DDR5 and LPDDR5 memory.
With this code changes, on DDR5 system with 2 Ch per DIMM, 32 bit
primary bus width per Ch showed the Total width as:
Handle 0x000F, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x0009
Error Information Handle: Not Provided
Total Width: 80 bits
Data Width: 64 bits
Size: 16 GB
...
BUG=b:194659789
Tested=On Alder Lake DDR5 RVP, SMBIOS type 17 shows expected `Total Width`.
Change-Id: I79ec64c9d522a34cb44b3f575725571823048380
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Make use of `smbios_bus_width_to_spd_width()` for filling DIMM info.
Additionally, ensures dimm_info_util.c file is getting compiled for
romstage.
TEST=dmidecode -t 17 output Total Width and Data Width as expected.
Change-Id: I7fdc19fadc576dec43e12f182fe088707e6654d9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The reason cbfs_cache was disabled on x86 was due to the lack of
.data sections in the pre-RAM stages. By using
ENV_STAGE_HAS_DATA_SECTION we enable x86 to start using the cbfs_cache.
We still need to add a cbfs_cache region into the memlayout for it to
be enabled.
BUG=b:179699789
TEST=Build guybrush and verify cbfs_cache.size == 0.
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I74434ef9250ff059e7587147b1456aeabbee33aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
FMAP was developed with assumption about endianness of the target machine.
This broke the parsing of the structure on big endian architectures. This
patch converts the endianness of the fields where applicable.
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I8784ac29101531db757249496315f43e4008de4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We only ever start and execute threads on the BSP. By explicitly
checking to see if the CPU is the BSP we can remove the dependency on
cpu_info. With this change we can in theory enable threads in all
stages.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS and verify coop multithreading still works
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iea4622d52c36d529e100b7ea55f32c334acfdf3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58199
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CPU_INFO_V2 now encapsulates the cpu_info requirements. They no longer
need to leak through to thread.c. This allows us to remove the alignment
requirement.
BUG=b:179699789
TEST=Reboot stress test guybrush 50 times.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I0af91feddcbd93b7f7d0f17009034bd1868d5aef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Julius Werner