Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=None
TEST=Build the magalor board.
Change-Id: I7bb19d6d4a66e66fed0564592c803c2af1045b0c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
H9HCNNNBKMMLXR-NEE
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
BUG=b:161215903
BRANCH=NONE
TEST=FW_NAME=madoo emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib61af2399541c4caf4a310a34e778e0ba1cbd3ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43802
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow schematic to modify USB port setting and clean up I2C clock tuning.
USB2 [0]: USB Type C Port 0
USB2 [1]: USB Type C Port 1
USB2 [2]: None
USB2 [3]: USB Type A Port 1
USB2 [4]: None
USB2 [5]: Camera
USB2 [6]: None
USB2 [7]: WLAN module - BlueTooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: USB Type C Port 1 (Sub/B side)
USB3 [2]: None
USB3 [3]: USB Type A Port 1
USB3 [4]: None
USB3 [5]: None
BUG=b:161407664
BRANCH=NONE
TEST=Build the coreboot image on madoo board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ia73593f52adee3806e725127891f084a08bf1360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43750
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If59502aec7c3ab55864a518d626cde52aee18373
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43746
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This copies over the USB daughterboard device tree config from volteer
to volteer2. These two boards are basically identical in this area so
the config should also be identical.
BUG=b:158673460
TEST=none
Change-Id: If8a82bc18b36d92a1c851b49612edfbefa18ec54
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BUG=b:161734657
TEST=Ensure that the discrete WiFi information is built into ACPI table.
Scope (\_SB.PCI0.RP01)
{
Device (WF00)
{
Name (_UID, 0x923ACF1C) // _UID: Unique ID
Name (_DDN, "WIFI Device") // _DDN: DOS Device Name
Name (_ADR, 0x00000000) // _ADR: Address
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x43,
0x03
})
}
}
Change-Id: I9a9259e167fc213291b89e151729553ec4649eaf
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43769
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Todor is created to take the place of terrador therefore
copying terrador content into todor's setup.
BUG=b:162110806
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TODOR
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I63151728a04f2252ca8a77158a2656ad8b1e1b51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Create the todor variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
In addition,
* sort the variant names in alphabetical order.
* todor uses the same config options as terrador.
BUG=b:162110806
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TODOR
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I7aa7acf1f3c3cc14b92ded05d5868818a627a432
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
All boards disable PIRQs, except purism/librem_bdw. Since IRQ0 is
invalid and modern OSes don't use PIRQ routing, disable the PIRQs.
Change-Id: I93b074474c3c6d4329903cab928dc41e1d3a3fb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the eldrid variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:162115131
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_ELDRID
Signed-off-by: MiceLin <mice_lin@wistron.corp-partner.google.com>
Change-Id: I1cd07ee7a87335e1e0b51d65c26bffc3bc46037c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Some smart battery patches have been backported to the ChromeOS 4.19 kernel,
and userspace can now access smart battery data from sysfs instead of using
the hacky ectool instead.
Also change all space indents into tab indents while we're here.
BUG=chromium:1047277
TEST=confirmed a /sys/class/power_supply/sbs-i2c device shows up
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I43687e63e4c1a7756c117129ced20749afc1b9e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use gpio_keys driver to add ACPI node for pen eject event. Also
setting gpio wake pin for wake events.
Removal and insertion (both edges) triggers IRQ and only removal is a
wake event (rising edge).
Adding for both Volteer and Volteer2 variants.
BUG=b:146083964
BRANCH=None
TEST=tested on a Volteer
Change-Id: Ida3217a5b156320856ce3302c2623eba2230f28d
Signed-off-by: Alex Levin <levinale@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43764
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MRC automatically detects the DDR type and sets Rcomp resistor
and target values for JSL and does not require explicit programming.
Change-Id: Ia130765e2cb91d6a39ad00ebbab20e7e87fa42d1
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the magolor variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:58540772
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_MAGOLOR
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I3e39e650b82a0aa629a48a00227700b058effb34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For devices sharing same firmware, there may be few customization based
on SKU ID - for example being clamshell or form factor. On Kukui and
Jacuzzi platforms the SKU ID is defined on AP SOC, so we have to send
the information to EC.
BUG=b:161767717
TEST=make -j # builds and boots on Juniper
BRANCH=kukui
Change-Id: I8ffdd9fd1e609c1dd4b0e22dc7aab560ccdc842e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43788
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
HDMI DDC GPIOs were configured as NC till now in waddledoo.
This may cause HDMI i2c transfer to break and EDID read will
fail due to wrong configuration
Configuring these GPIOs as NF in coreboot to fix the issue.
BUG=b:160324327
BRANCH=None
TEST=HDMI works on DDI2 onn Type-C port
Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C bus3 frequency and insure it meets I2C spec.
BUG=b:161650117
TEST=flash coreboot to the DUT and actual measured I2C bus3
make sure it meet Spec.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Ifa9f0bce723f55a12fd2313788c995f8326e3e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's a `GPL-2.0-or-later` version of this file in volteer2, so use it
in place of these weirdly-licensed files.
Change-Id: Icde2f6539d9c726d6967350f74e7bc015e01e7b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This applies what commit 79572e4f32 does
to the devicetree settings of the zork devices.
Change-Id: Ife94818d771f137e56c51ad1598148f60fcf5345
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43820
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since FSP pre-populates the UPD struct with the non-zero default values,
coreboot shouldn't set them to zero in the case that they aren't
configured in the board's devicetree. Since all parameters being zero is
a valid case, this patch adds another devicetree option that applying
the devicetree settings for the USB2 PHY tuning depends on being set.
BUG=b:161923068
Change-Id: I66e5811ce64298b0644d2881420634a8ce1379d7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43781
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set power limits in devicetree for Tiger Lake Y-SKU based volteer
variant boards.
BUG=b:152639350
BRANCH=None
TEST=Built and tested power limits on volteer variant board.
Change-Id: If4f1226473b48365e5962df9fff29910c99007fc
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43607
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In the middle of the Great DPTF Refactor of 2020, new volteer variants
were added, but their dptf.asl files are no longer used, so delete them.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I52f2042aa870a29026eb9fe122340ad07654e706
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The Raydium ACPI entry currently provides a reset GPIO and an _ON/_OFF
method to the kernel. These are contradictory. The ownership of the GPIO
should be mutually exclusive between either the OS or the FW. Since we
have two methods exposed this causes the OS to reset the TS twice. Once
using the _ON method, and once using the GPIO. Additionally the _ON
method is waiting for 20ms after reset while the OS driver uses a 50ms
delay. The Raydium TS datasheet specifies 20ms for FW ready time, so the
OS driver is adding additional padding.
The reference design has a 32ms rise time on the reset line. So without
this patch, the OS tries to reset the TS using the _ON method and it
waits for 20ms. This is not enough time for the reset line to reach
high, let alone account for the FW ready time. The OS driver then tries
to reset the device by toggling the GPIO. It waits 50ms which is still
2ms less than required.
This CL removes the GPIO from being exported in the _CRS so the OS
driver won't try and reset the device. It also increases the reset delay
by 32ms to account for the rise time.
This isn't a complete fix. I think that the slow rise time is causing
some kind of metastability in the TS reset hardware. Using a script to
bind and unbind the TS driver, the TS device becomes unresponsive after
~200 iterations. The only way to reset the device is to power cycle.
The TS power is also not currently controlled by the power resource.
This means that we have no guarantee over when the reset line is
toggled. This will lead to issues while spending and resuming.
BUG=b:160854397
TEST=Boot trembyle and make sure TS works. Suspend/Resume trembyle 300+
times.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I23131be5d7109eed660a8bd6e2c156c015aa3c4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Earlier versions of Dalboz did not correctly handle HS400. One fix was
to add stitching vias, but these boards did not have them. b/156539551
Another possible fix is to add tuning parameters including drive
strength, but that is still a WIP. b/158959725
This should correct OS load failures in the meantime by running the bus
slower.
BUG=b:158845662
TEST=build, flash, boot sku 0x5a80000c to OS
BRANCH=None
Signed-off-by: Eric Peers <epeers@google.com>
Change-Id: Ia3e7a641bde04c5a7be29bf91c38dd8c110ed17a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43572
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the dirinboz variant of the dalboz reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:161579679
BRANCH=master
TEST=util/abuild/abuild -p none -t google/zork -x -a
make sure the build includes GOOGLE_DIRINBOZ
Change-Id: I33c03080ffbe0bca61acf4144417b9f5fff6389f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reset the Touchscreen (TS) and disable the stop GPIO (report switch) at
the same time. Add a delay of 100 ms after disabling the stop GPIO. This
will ensure the required delay is inserted for both reset and stop
disable GPIOs simultaneously.
BUG=b:152936541
TEST=Build and boot the waddledoo mainboard. Ensure that the SiS
Touchscreen is functional.
Change-Id: Icbfb5e07a28ab72b1ff696ad1183a6c2173dcaac
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43453
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
H9HCNNNBKMMLXR-NEE
K4U6E3S4AA-MGCR
BUG=None
TEST=Build the drawcia board.
Change-Id: Id05c0b2a87b64bfedc761949cbc8ad6cf7dd73a5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43505
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change does the following:
a. USI_REPORT_EN is no longer set to high in coreboot. Instead
GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this
pad as required.
b. Appropriate delays are added for power-down sequencing:
- Delay after REPORT_EN is disabled - 1ms
- Delay after RESET is asserted - 1ms
BUG=b:159501288
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: If4d12fa0d4f4e5123d8fdccdabda996dcafa4523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPIO_91 is added to ACPI using the device tree entry for codec. So,
this change drops the TODO from GPIO table.
Change-Id: I9c2e91465ab554126531f8512028360ae5fb316d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
