`cbfstool locate` and the associated -T switch were removed a looong
time ago (2015 in CB:11671). However, getopt and the help text weren't
cleaned up correctly. Fix that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib098278d68df65d348528fbfd2496b5737ca6246
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The whole point of moving do_cbfs_locate() later (CB:59877) was that it
could use the file size that is actually going to be inserted into CBFS,
rather than the on-disk file size. Unfortunately, after all that work I
forgot to actually make it do that. This patch fixes that.
Since there is no more use case for do_cbfs_locate() having to figure
out the file size on its own, and that generally seems to be a bad idea
(as the original issue shows), also remove that part of it completely
and make the data_size parameter mandatory.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1af35e8e388f78aae3593c029afcfb4e510d2b8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Set open-drain GPIOs for ChromeOS as input and high-z mode.
After applying this patch, we can measure these pins from 1.0V to
correct voltage (1.8V) to prevent wrong judgement of low/high.
Reference document:
MT8186_SoC_Pinmux_V1_1
BUG=b:209342636
TEST=measure pins voltage 1.8V on kingler board
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ib55a773bb63404a1b952f7e7645eb7aba6638b00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tracker is a debugging tool, and MT8186 only supports AP tracker.
When bus timeout occurs, the system reboots and latches some values
which could be used for debugging.
This function will be triggered only when it encounters the bug
hanging issue.
BUG=b:202871018
TEST=range of registers are dumped as expected.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ie023de2a6f7421a16b2516baa0bf0bf6fff589e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The second generation EFS (offset 0x24[0]=0) uses "binary relative"
offsets and not "x86 physical MMIO address" like gen1.
The field additional_info in table header can tell if the absolute or
relative address is used.
Chips like Cezanne can run in both cases, so no problem
comes up so far.
The related change in psp_verstage has been uploaded.
https://review.coreboot.org/c/coreboot/+/58316
The relative mode is the mode 1 of four address modes. The absolute
mode is the mode 0. Later we will implement mode 2. Not sure if mode 3
is needed.
It needs to be simple to work with psp_verstage change to make SOC
Cezanne work quickly. This patch is defacto a subset of
https://review.coreboot.org/c/coreboot/+/59308
which implements the framework of address mode and covers mode
0,1,2. Some hardcode value like 29 can be removed in 59308.
BUG=b:188754219
Test=Majolica (Cezanne)
Change-Id: I7701c7819f03586d4ecab3d744056c8c902b630f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
1. Fix the inconsistence of the target path of U-Boot payload
between Kconfig and Makefile.inc.
2. Perform full clone (to the destined commit) in order to get
tags.
3. Move stable commit id of U-Boot payload from Makefile to
Kconfig, and make prompt consistent with it.
Change-Id: Ic0f11c16274456a452a0422e19fab0c61d8b5d5b
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are two versions for tracker system:
Version 1 for MT8186, and version 2 for MT8192 and MT8195.
Reference document:
MT8169_bus_dbg_tracker_cfg_reg.xls from MediaTek internal.
BUG=b:202871018
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Idb146974da118b1cf5a349370bf7b2fa13f1aba8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59989
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add PSP_S0I3_RESUME_VERSTAGE Kconfig option. When enabled, verstage will
be run in PSP during S0i3 resume. Setting softfuse bit 40 enables this
in PSP.
BUG=b:200578885, b:202397678
BRANCH=None
TEST=Verstage runs during s0i3 resume on Nipperkin
Change-Id: I2c185f787c1e77bd09f6cbbb1f47deb665ed0c79
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The OEM may create and sign an Audio component to extend the Audio
capability provided by Intel. The manifest is then signed, and the
signature and public key are entered into the header of the manifest
to create the final signed component binary. This creates a secure
verification mechanism where firmware verifies that the OEM Key
Manifest was signed with a key owned by a trusted owner. Once OEM KM
is authenticated, each public key hash stored within the OEM KM is
able to authenticate the corresponding FW binary.
Link to the Document:
https://www.intel.com/content/www/us/en/secure/design/confidential/software-kits/kit-details.html?kitId=689893
ADL_Signing_and_Manifesting_User_Guide.pdf
BUG=b:207820413
TEST:none
Signed-off-by: ravindr1 <ravindra@intel.com>
Change-Id: Id52b51ab1c910d70b7897eb31add8287b5b0166f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With the elimination of remaining non-verifying CBFS APIs in CB:59682,
CBFS verification is now ready to be used in its simplest form, so
enable the respective Kconfig options in menuconfig. Add a few more
restrictions to the TOCTOU_SAFETY option for problems that haven't been
solved yet, and transform a comment in cbfs.c into a die() to make sure
we don't accidentally forget implementing it once vboot integration gets
added.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ifeba5c962c943856ab79bc6c4cb90a60c1de4a60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
In cbfs_add_component(), the |offset| variable confusingly jumps back
and forth between host address space and flash address space in some
cases. This patch tries to clean that logic up a bit by converting it
to flash address space very early in the function, and then keeping it
that way afterwards. convert() implementations that need the host
address space value should store it in a different variable to reduce
the risk of confusion. This should also fix a tiny issue where
--gen-attribute might have previously encoded the base address as given
in CBFS -- it probably makes more sense to always have it store a
consistent format (i.e. always flash address).
Also revert the unnecessary check for --base-address in
add_topswap_bootblock() that was added in CB:59877. On closer
inspection, the function actually doesn't use the passed in *offset at
all and uses it purely as an out-parameter. So while our current
Makefile does pass --base-address when adding the bootblock, it actually
has no effect and is redundant for the topswap case.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Idf4721c5b0700789ddb81c1618d740b3e7f486cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Add ALC5682I-VS codec support. ALC5682I-VD/ALC5682I-VS load different
hid name depending on SSFC.
BUG=b:198722640
BRANCH=octopus
TEST=Set CBI SSFC BIT9-11 to select codec, and test audio works
Change-Id: I80be12d88e100ce8586371fc49b36447859e24f8
Signed-off-by: Paul Huang <paul2_huang@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name and machine_dev depending on the AUDIO_CODEC_SOURCE
field of fw_config. Define FW_CONFIG bits 36 - 37 (SSFC bits 4 - 5)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:198689479
BRANCH=zork
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I0c78aa166010ffa4d0cacc8a11d418d5a6906749
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59558
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently coreboot and EC had different logic to interpret TCSS port
number which would break retimer update functionality since coreboot
would pass wrong port information to EC.
To correct this, coreboot has implemented function which converts
coreboot physical port mapping to EC's abstract port mapping.
Each SoC needs to implement this weak function since only SoC will have
correct physical port mapping data. This function should resolve issue
of port mismatch since coreboot will count only enabled ports and
provide correct EC port number in return.
BUG=b:207057940
BRANCH=None
TEST=Check if retimer update works on Redrix and correct port
information is passed to EC.
Change-Id: I3735b7c7794b46123aba3beac8c0268ce72d658c
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently coreboot interprets TCSS port number as per physical port
number while EC abstracts port number and provides indices as port
number. For example, if TCSS port 1 and 3 are enabled on the board,
coreboot will interpret port numbers as 0 and 2, but since only 2 ports
are enabled in the system EC will assign port numbers as 0 and 1.
This creates a port number mismatch while communicating between EC and
coreboot. This patch addresses issue where SoC can implement function
to map correct EC port as per port enabled in mainboard.
BUG=b:207057940
BRANCH=None
TEST=Check if code compiles successfully. Functionality will work once
function is implemented in SoC code.
Change-Id: Ia7a5e63838e6529196bd211516e4d665b084f79e
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
For additional power savings during RTD3, the PMC can power-gate the
ModPHY lanes that are used by the PCH PCIe root ports. Therefore,
using the previous PCIe RP-type detection functions, implement ModPHY
PG support for the PCH PCIe RPs.
This involves:
1) Adding a mutex so only one power resource accesses the PMC registers
at a time
2) OperationRegions to access the PMC's PG registers
3) Adding ModPHY PG enable sequence to _OFF
4) Adding ModPHY PG disable sequence to _ON
BUG=b:197983574
TEST=50 S0ix suspend/resume cycles on brya0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I19cb05a74acfa3ded7867b1cac32c161a83b4f7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59855
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to distinguish PCH from CPU PCIe RPs, define the
soc_get_pcie_rp_type function for Alder Lake. While we're
here, add PCIe RP group definitions for PCH-M chipsets.
BUG=b:197983574
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7438513e10b7cea8dac678b97a901b710247c188
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
In order to distinguish PCH from CPU PCIe RPs, define the
soc_get_pcie_rp_type function for Tiger Lake.
BUG=b:197983574
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic3f7d3f2fc12ae2b53604cd8f8b694a7674c3620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add entry in ACPI table under IPU device to provide silicon type
information to IPU driver. IPU kernel driver can decide the type of
firmware to load based on this information.
BUG=b:207721978
BRANCH=none
TEST=Check for the ACPI entry in the SSDT after booting to kernel
Change-Id: I4e0af1dd50b9c014cae5454fcd4f9f76d0e0a85f
Cq-Depend: chromium:3319905
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The commit d023909b "treewide: Disable R_AMD64_32S relocation support"
clflush the address stored in _cbmem_top_ptr, which is the same address
cbmem_top() returns, instead of clflush _cbmem_top_ptr itself.
Fix that by providing the correct address to clflush.
Change-Id: If74591e7753cd9c3c097516430a212d416f53e4d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
`meminit_memcfg()` does common memory configuration, which is not
specific to each DIMM. Thus, move it out of the for-loop and call it
once.
Change-Id: If74875b45cd0d7a759883eaf564505ebf281bed5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The headers added are generated as per FSP v2471_02.
Previous FSP version was v2422_01.
Changes Include:
- UPDs description update in FspsUpd.h
- Adjust UPD Offset in FspmUpd.h and FspsUpd.h
BUG=b:208336249
BRANCH=None
TEST=Build and boot brya
Change-Id: I4d04652c06a1c1823d3859be209710c273a2ae8c
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Implement __fls() as an alias for log2(), and remove the duplicate
definitions in commonlib/storage/sdhci.c.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ib458abfec7e03b2979569a8440a6e69b0285ac32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
All Tiger Lake mainboards use the default value for the setting
`SataMode`. Thus, drop it from their devicetree.
Change-Id: I291048250bc82552fde7c71a1dcda4894a61d465
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59890
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Coffee Lake mainboards use the default value for the setting
`SataMode`. Thus, drop it from their devicetree.
Change-Id: Ibb329eb8b752c2220bb25f14fb6ae92dd8a308d6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59889
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Skylake mainboards use the default value for the setting `SataMode`.
Thus, drop it from their devicetree.
Change-Id: I9be5eca93cac65afc4cc30ceb64d9a5b7e5cd514
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59888
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Device 4 was introduced with a wrong name, since it is the SA Thermal
Subsystem and it does nothing have to do with DSP. Thus, rename it
accordingly.
Change-Id: I8edc764413df5f323098e60d0a3f0f87a7e656cb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60049
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch includes (edk2/edk2-stable202111) all required
headers for edk2-stable202111 EDK2 tag from EDK2 github
project using below command:
>> git clone -b edk2-stable202111 https://github.com/tianocore/edk2.git
commit hash: bb1bba3d776733c41dbfa2d1dc0fe234819a79f2
Only include necessary header files.
MdePkg/Include/Base.h was updated to avoid compilation errors
through safeguarding definitions for MIN, MAX, NULL, ABS, ARRAY_SIZE.
Note: edk2-stable202111 tag is required to adopt FSP 2.3 specification.
- Need to add ExtendedImageRevision in FSP_INFO_HEADER structure.
- Need to add FSP_NON_VOLATILE_STORAGE_HOB2 header.
Change-Id: I786cc05f9a638ac6226ebc8c0eaf1dc8189a4ca4
Signed-off-by: Subrata Banik <subi.banik@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Currently, `checkpatch.pl`, imported from the Linux project, checks for
75 characters per line [2]:
> Suggest line wrapping at 75 columns so the default git commit log
> indentation of 4 plus the commit message text still fits on an 80
> column screen.
But Gerrit’s Web interface and its commit hooks use with 72 characters
per line [2]:
remote: commit 35bb56d: warning: too many message lines longer than 72 characters; manually wrap lines
remote:
remote: SUCCESS
remote:
remote: https://review.coreboot.org/c/coreboot/+/60004 [DO NOT SUBMIT] Gerrit commit msg line length test [NEW]
So, decrease the suggested length from 75 to 72 characters per line.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2a076f40d8c9be95bee7bcf18436655e1140447f
[2]: https://review.coreboot.org/60004
Change-Id: Ic9c686cb1a902259b18377b76b5c999e94660fed
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds a new way of implementing flash access for libpayload.
Until now all reads had to be performed using cbfs_media, which is
obsolete. From now on all reads should be performed using
boot_device_read().
This patch also provides a default implementation of boot_device_read()
for x86 architecture.
Change-Id: I1babd2a8414ed9de3ca49903fcb4f036997b5ff3
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With very little changes this code can be used to initialize systems
without SMP. The linker will remove most of the code.
Change-Id: Ia0e8fdf8ed7bc2e0e4ff01be8d3e3c3cb837e6c7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In commit 667471b8d8 (ec/google/chromeec: Add PLD to EC conn in ACPI
table), PLD is added to ACPI table. It causes the DUT to not boot into
the OS. So fix the USB3/USB2 Type-C Port C2 PLD group order from 3 to 2
to solve this issue.
Fixes: 667471b8d8 ("ec/google/chromeec: Add PLD to EC conn in ACPI table")
BUG=b:209723556
BRANCH=none
TEST=build coreboot and boot into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ia4cf2d735de524ae721800600536923d1d47f04b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The `cpu_get_power_max()` function returns the TDP in milliwatts, but
the vr_config code interprets the value in watts. Divide the value by
1000 to fix this.
This also fixes an integer overflow when `cpu_get_power_max()` returns
a value greater than 65535 (UINT16_MAX).
Change-Id: Ibe9e0db6762eee5cc363f8b371c8538eb92f6308
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Enable TPM init in bootblock so that all further stages and other CBFS
files are directly measured into PCRs immediately instead of being
logged into a buffer and replayed to the TPM in ramstage.
Change-Id: Ib3ac29aa72abe8e967660ae7e8416aeb8812de26
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
coreboot code currently supports different UDK binding as per
underlying FSP requirement, example: ICL and TGL uses
UDK_2017_BINDING while ADL uses UDK_202005_BINDING Kconfig.
These UDK binding Kconfigs are being used to choose the correct
UDK_VERSION.
This patch introduces `UDK_BASE` Kconfig option so UDK_VERSION
if clause don't need to add specific UDK binding Kconfig everytime with
introduction of newer UDK bindings in future.
Tested with BUILD_TIMELESS=1, Hatch remains identical.
Change-Id: I64c51aa06a14f0ce541537363870ac3925b79a68
Signed-off-by: Subrata Banik <subi.banik@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
ADL-P silicon can support 7 SRC CLK's and 10 CLKREQ signals. Out of 7
SRCCLK's 3 will be used for CPU, the rest are for PCH. If more than 4
PCH devices are connected on the platform, an external differential
buffer chip needs to be placed at the platform level.
A mainboard designer can choose to add an external clock chip, and
select the SRC CLK using CONFIG_CLKSRC_FOR_EXTERNAL_BUFFER.
CONFIG_CLKSRC_FOR_EXTERNAL_BUFFER provides the CLKSRC that feed clock to
discrete buffer for further distribution to platform.
TEST=Able to detect SD card connected at x4 PCIe Gen 3 Slot.
localhost ~ # dmesg | grep mmc
[ 4.997840] mmc0: SDHCI controller on PCI [0000:ae:00.0] using ADMA
[ 5.460902] mmc0: new ultra high speed DDR50 SDHC card at address aaaa
[ 5.473555] mmcblk0: mmc0:aaaa SS08G 7.40 GiB
[ 5.494268] mmcblk0: p1
Change-Id: I21f1155374049c90aa45db25d4128b39aa5898bb
Signed-off-by: Subrata Banik <subi.banik@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds the setting of PsysPmax to 143 W according to
gimble board design.
BUG=b:206990759
TEST=emerge-brya coreboot chromeos-bootimage & ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I851e0871461a9a9769c6b84f7d8287d989c23f06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As per the schematics, smart card is expected to operate in normal mode
by default. So configure the SOC_SC_PWRSV gpio accordingly.
BUG=b:202992077
TEST=Build and boot to OS in Nipperkin board version 2.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8e12600ad45734b144a30c868f0e4f323aa056f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Julius Werner