Since the OS provides its own driver for the I2C controller it can
choose to use a bus speed other than the one used at coreboot runtime.
In this case it would be good to provide a way how the needed bus
timings are communicated to the OS, since these are very board-specific
and there is no way that the OS can know them other than read the
appropriate ACPI reported timings.
This patch adds some code to report additional bus speed timings if
there are some defined in the devicetree.
Change-Id: If921e0613864660dc1bb8d7c1b30fb9db8ac655d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch adds the ACPI hardware error source table (HEST) support.
This involves a few different parts: (1) The ACPI HEST table which is filled
with the appropriate fields (2) Reserved memory which is used by runtime
SW to provide error information. OS will not accept a HEST table with
this memory set to 0.
The ASL code to enable APEI bit will be submitted in a separate patch.
Tested on DeltaLake mainboard with following options enabled
SOC_INTEL_XEON_RAS
After boot to Linux, the following will show in dmesg:
HEST: Table parsing has been initialized
Change-Id: If76b2af153616182cc053ca878f30fe056e9c8bd
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This reverts commit 255b6f8646.
No longer needed after commit dd01e0131a
(Revert "util/lint: Add test for documentation in util dirs") has been
submitted. Plus, `util/vboot_lib/description.md` gets deleted whenever
one runs `make -C util/cbfstool clean`, which is rather annoying.
Change-Id: Ic93da096b6186d1d2af12243a74ec597694960c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55162
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for loading SPM firmware from CBFS to SPM SRAM.
SPM needs its own firmware to enable SPM suspend/resume function which
turns off several resources such as DRAM/mainpll/26M clk when linux
system suspend.
TEST=program counter of SPM is correct value after booting up.
Change-Id: Ia0f9b9f86e44b293c1cc47213946304c64aea75e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55140
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use currently global_lp4x_mem_parts.json.txt to regenerate SPD files for
LP4x memory parts that can be used with ADL-based mainboards.
BUG=b:186616388
Change-Id: I5e76a887f81d432adbcfc2f8956b44f4343db5c2
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
CB:52586 ("util/spd_tools: Add MT53E1G32D2NP-046 WT:B LPDDR4 config")
incorrectly set ranks per channel to 1. However, MT53E1G32D2NP-046 WT:B
part has 2 channels per die and 2 physical dies. Each channel in each die shares DQ-DQS lines with the channel in other die and uses separate CS lines. Thus, number of ranks per channel is 2.
This change fixes the attribute ranksPerChannel for MT53E1G32D2NP-046 WT:B in LP4x global config by setting it to 2.
BUG=b:186616388
Change-Id: Iba87754ca04c2e026a9cbc8ef07412b467140cba
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to support no MIPI camera variant, move related configuration into variant folder.
BUG=b:188272162
BRANCH=none
TEST=build no MIPI camera variant without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4e64d078a8e39732ad29443c3b09ca008a7e902f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Load SSPM firmware and boot up SSPM in ramstage.
This adds 23ms to the boot time.
TEST=Load SSPM blob ok, and we can see some logs of SSPM from AP.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ia227ea9f7d58129068cb36ec2de7d9feb677006b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Since the MCA(X) registers have defined values on the cold boot path,
the is_warm_reset check can be dropped. Also the warm reset bit in the
NCP_ERR register doesn't behave as the PPR [1] suggested; no matter if
something was written to the register or the machine went through a warm
reset cycle, the NCP_WARM_BOOT bit never got set.
[1] checked with PPR for AMD Family 17h Models 11h,18h B1 (RV,PCO)
#55570 Rev 3.15
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4e6df98ffd5d15ca204c9847a76c19c753726737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The e820 type don't fully match the LB_TAG_MEMORY types, so change all
unknown types to e820 to '2', reserved memory.
TESTED with Linuxboot: e820 now shows the CBMEM region as reserved.
Change-Id: Ie0e41c66e002919e41590327afe0f543e0037369
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55074
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Rocky Phagura
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on schematic and gpio table of volet, update gpio and
devicetree settings for volet Proto.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia0e9557e01ce1e7a49a3dddf6da3e4a29587a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55113
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add 1 port and 1 endpoint
2. Add support for OVTI8856
WFC is on I2C0
BUG=None
BRANCH=None
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Ic5e9c28f255bdf86a68ce80a4f853be4e7c7ccfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This will be used to pass information to driver through ACPI in devicetree.
Example https://review.coreboot.org/c/coreboot/+/52013
register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3"
register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ"
TEST=Add these macros in devicetree, build and check static.c for consistency
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.corp-partner.google.com>
Change-Id: Ia4137e09c934bf06857ceedb933e616bed5070dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55097
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
We are also present on Slack so advertise that.
Change-Id: I7d9887e524e47e6f42a5013e9f696881ef54a631
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
OCP Delta Lake is developed and validated against LinuxBoot payload.
Need to put the respective binary blobs in site-local/deltalake to
build the final coreboot image.
Add LINUX_COMMAND_LINE for LinuxBoot payload kernel cmdline,
CPU_UCODE_BINARIES for CPU microcode binary, CONSOLE_SERIAL_57600 is
the serial baud rate used by OCP Delta Lake, DEFAULT_CONSOLE_LOGLEVEL_4
is for a faster boot time.
Tested=On OCP Delta Lake it can boot up target CentOS 8 GNU/Linux OS.
Change-Id: Ib494e4170a7ebb445d9e11df83c370b40a9e5194
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55058
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a leftover when migrating to C_ENV_BOOTBLOCK
Change-Id: Ibc610cd15448632dc13d87094853d9b981e2679b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Guybrush platform needs to set up some GPIOs immediately before the
FSP-M runs. Add a platform specific call. This will be used in a
follow-on commit.
BUG=b:184796302, b:184598323
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I37d2625ff426347852e98a9a50f15368e0213449
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54638
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PLTRST# is currently asserted and latched when eSPI_RST# gets asserted.
If eSPI_RST# isn't used on a platform or it doesn't properly assert
in all cases, then PLTRST# will never be asserted. This could result in
the AP and EC being out of sync.
BUG=b:188188172, b:188935533
TEST=Warm reset guybrush with partial #22 rework. Verify that peripheral
channel is correctly reset.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I20d12edf3efc6100096e24aa8d1aec76bbde264f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Test-local config override headers were generated to paths missing
/tests/ infix, thus creating divergent tree in build output directory.
This patch fixes it moving generated config headers to the test-local
build directory.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ic5f3ba287ba3e9f5897cbaac64e88c2809f52d73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
There are cases where the RTC_VRT bit in register D stays set after a
power failure while the real date and time registers can contain rubbish
values (can happen when RTC is not buffered). If we do not detect this
invalid date and/or time here and keep it, Linux will use these bad
values for the initial timekeeper init. This in turn can lead to dates
before 1970 in user land which can break a lot assumptions.
To fix this, check date and time sanity when the RTC is initialized and
reset the values if needed.
Change-Id: I5bc600c78bab50c70372600347f63156df127012
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54914
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a function to check sanity of a given RTC date and time.
Invalid values in terms of overrun ranges of the registers can lead to
strange issues in the OS.
Change-Id: I0a381d445c894eee4f82b50fe86dad22cc587605
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Werner Zeh