The original ME code was assuming that the only type of messages
it would send were MKHI type and so it had some embedded checks
for that header and that type of message.
In order to support ICC messages this needs to change to handle
different header types, so now the header will be sent first
and then the data will follow, rather than the two both being
sent in the same low-level function.
This change has no real affect on the system, subsequent commit
will add new ICC messages.
Change-Id: I52848581e49b88c0a79e8bb6bda2a179419808a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65249
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4449
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the EC requests the host to throttle (for charging or thermal
related reasons) the package power consumption will be limited.
Right now this is set at 12W but that is somewhat arbitrary and may
need tuning.
1) define the THRT method in \_TZ scope for EC to call
2) enable SCI events for throttle start and stop
3) define the power limit at 12W and set it in NVS
1) Enable CONFIG_ACPI_DEBUG=y in the kernel
2) Enable the Debug object event in acpi module
acpi.debug_layer=0x7f acpi.debug_level=0x2f
3) Using EC console generate host event for throttle start
> hostevent set 0x20000
4) Check dmesg for throttle start events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q12] (Node ffff8801002c5988)
[ACPI Debug] String [0x12] "EC: THROTTLE START"
[ACPI Debug] String [0x10] "Enable PL1 Limit"
5) Using EC console generate host event for throttle stop
> hostevent set 0x40000
6) Check dmesg for throttle stop events
ACPI: Execute Method [\_SB_.PCI0.LPCB.EC0_._Q13] (Node ffff8801002c59b0)
[ACPI Debug] String [0x11] "EC: THROTTLE STOP"
[ACPI Debug] String [0x11] "Disable PL1 Limit"
Change-Id: I39b53a5e8abc2892846bcd214a333fe204c6da9b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63989
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4416
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Two new events possible from the EC for starting and stopping throttle.
These are handled in a per-board method that is defined under the
thermal zone. This is not quite where I wanted it but the scoping
rules in ACPI don't let me have a defined external object in the
same scope.
Change-Id: I766f07b4365b29df3daa8e45e88f7c38c645c287
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63988
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4415
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the edid data structure changed a while ago, it caused hangs on snow
which were fixed by adding those missing members. Unfortunately we didn't
realize that pit needed the same fix.
Change-Id: I81780b8135b99b2e24af723e703b9befff7b5ef0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63646
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4389
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
An issue was observed using a specific vendor's TPM in that it
chokes on access to registers that are not explicitly defined in the
PC client specification. The previous driver used generic access
functions for reading and writing registers. However, issues come
to play when reading from the status register. It read it as a 32-bit
value, but that read address 0x1b which is not defined in the spec.
Instead of using generic access functions for the tpm registers
provide explicit ones. To that end provide more high level wrapper
functions to perform the semantic access required.
Change-Id: I781b31723f819e1387d7aa25512c83780ea0877f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63243
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4388
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
That speed is used with U-Boot instead of the more conservative 500 KHz.
Change-Id: Ie9d79db3b52b88c1f3bfec1745634ae6bdc9f4ee
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63193
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4386
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some registers and bit fields were wrong, but the difference is mostly
academic since the code that uses them are never called.
Change-Id: I0ce5e1529cdda1a4973765af8c31b79130b1111c
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63189
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4385
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The divisor mask had been set to 0xff, but the bitfield is 4 bits wide.
Change-Id: Id8a205c80ca2fb0b6f0d86a0c3be4bba9527c0b5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63188
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4384
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This functions are by definition changing the data pointed to by their
arguments, so they shouldn't by const.
Change-Id: Id29b3f76526aba463f8bb744f53101327f9c7bde
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63777
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4400
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The timer code was supposed to be using the mct, and also using the monotonic
timer infrastructure instead of the get_timer function. This change had been
made for the 5250 but not yet for the 5420.
Change-Id: I03a4fbb434f2346761f28fb6bd2218b526f2a4a2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64159
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4418
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This code was left over from U-Boot and was superceded by the MCT.
Change-Id: Ia85e3b7281dcdd4740238dddd0dfc6f0ba2c94da
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63778
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4401
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the const was removed from write function arguments, a related bug in the
5250 code was fixed so that it would still compile. Unfortunately, that same
change needed to be made to the 5420.
Change-Id: If15057c92422de91dc8e35dbd8b5c978bfae122a
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64154
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4417
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The code generally intended to make the pointer const instead of the thing it
pointed at, but it had const backwards. Sometimes both the pointer and the
data could be const, but sometimes there were writes where only the pointer
should be.
Change-Id: Ifcd5495769b86b47d7b583cce63ed5c2158bec4e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63775
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4397
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The cache.h header uses standard int types but doesn't include stdint.h itself.
Change-Id: If470978164b0cd1f05c27c2c8eda365133cc47ff
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63190
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4387
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Now that the rtd2132 device has the full settings the
panel timings need to be implemented. Sadly, the Tx timings
in the rtd2132 aren't 1:1 with the panel's Tx timings. Below
is the table equivalent:
RTD2132 | Falco Panel
--------+------------
T1 | T2
--------+------------
T2 | T8+T10+T12
--------+------------
T3 | T14
--------+------------
T4 | T15
--------+------------
T5 | T9+T11+T13
--------+------------
T6 | T3
--------+------------
T7 | T4
--------+------------
Change-Id: I10a3ad475d6b9485a707eb49e31afd197fc8d24d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65858
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4472
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It has been disseminated that the RTD2132 chip
needs to be fully programmed for settings to take affect.
Most of the settings are note documented very well and
present themselves as magic values. Also, the wait time
for starting the sequence needs to be bumped from 2ms to 60ms.
Lastly, expose all the known settings through devicetree.
Change-Id: I9eeea9c4a13ec20b8ce1c5297e43c4dd793d90e5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65857
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When we go through the resume path, there shouldn't ever be a need to
initialize the PS/2 keyboard. The OS is going to reinitialize it
anyway, and it just slows the resume.
Verified Code flow in normal boot/S3 resume with print statements.
Verified Keyboard was correctly disabled and flushed by booting
to recovery mode screen while pressing keys on the integrated
keyboard.
Change-Id: I48bdca2fa2cc0c965401d10fef75cadb09d2e1e9
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63648
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4396
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add a function to disable and clear the keyboard controller.
Verified Code flow in normal boot/S3 resume with print statements.
Verified Keyboard was correctly disabled and flushed by booting
to recovery mode screen while pressing keys on the integrated
keyboard.
Change-Id: I3e1f011c3436fee5ce10993c6c26a3c8597c6fca
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63627
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4395
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- prints hex and ascii
- detects duplicate all zero lines
Change-Id: I557fed34f0f50ae256a019cf893004a0d6cbff7c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/62655
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/4392
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The hexdump function was added to libpayload recently, but its source file was
never added to the Makefile so it wasn't compiled or linked in.
Change-Id: Ic3c12a5b8a6ea631b83c10a6e4210544ff00b5bf
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64878
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4439
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The PWM is controlled externally from the APU.
Change-Id: Ia5130d7616991a78dfde44043a60a32cee4f145c
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61513
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4363
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
What gets written into the parade is highly mainboard-dependent.
So the parade_writes array needs to be there.
Change-Id: Ia382d9bf1929e67b7c14d7a09f5461b71866a16b
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61486
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4362
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
This is a clone of a Falco change:
I1a0df80dd47fdbd535aca7a9d49253794c480606.
Change-Id: I625dfbb228d1f293b880a52dfe552842d55a17d1
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63220
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4383
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
... based on the EDID detailed timing values for
pixel_clock and link_clock.
Two undocumented registers 0x6f040 and 0x6f044 correspond to link_m and link_n
respectively. Other two undocumented registers 0x6f030 and 0x6f034 correspond
to data_m and data_n respectively.
Calculations are based on the intel_link_compute_m_n from linux kernel.
Currently, the value for 0x6f030 does not come up right with our calculations.
Hence, set to hard-coded value.
Change-Id: I40ff411729d0a61759164c3c1098504973f9cf5e
Reviewed-on: https://gerrit.chromium.org/gerrit/62915
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4381
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This code is left over from what the VBIOS did; It is redundant.
Change-Id: I321c867c81ec8b4d5e10f8b51b872cecb3082d97
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/62290
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/4380
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Turn on the pei_data flag that will instruct the reference code
binary to route all USB ports to the XHCI controller on resume and
disable the EHCI controller(s).
Change-Id: I2f2ed853a6d17f90ea524bc516f3e78079222739
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63798
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4404
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The linux kernel will unconditionally route all USB
ports to the XCHI controller at boot. The EHCI controller
can then be disabled, and it should be left disabled
by the reference code when this is done.
However not all OS may do this unconditional route,
so provide an option to the reference code binary to
enable this behavior.
Change-Id: Iedf5af54182bf109cd1119c1999e46300665d41e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63797
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4403
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
SATA is routed to PIRQG which should be interrupt 22
and not interrupt 21. The kernel uses MSI with this
device so this is only seen when booting with pci=nomsi
Change-Id: Ic90ca2c561fc4c53ec1d395c05872222c65ff98a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63796
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4398
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The EHCI driver defines a maximum transfer timeout of two seconds. The
comments state that during tests the maximum amount of required transfer
time was for the SCSI TEST_UNIT_READY command on certain devices. We
have now observed a USB device (Patriot Memory 13fe:3100) that can NAK
this command for slightly more than two seconds. It will also completely
fail if the timeout hits, since it gets confused by the subsequent CSW
retry/recovery mechanism and starts producing babble errors. This patch
increases the timeout to three seconds to circumvent this problem.
To test, boot a Falco from a red-black RageXT USB stick.
Change-Id: I3c4fef468fb16eacc5a487d76d025a78fb450e27
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63095
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/4379
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Since these boards do not support C10 we should not bother
advertising that state in the ACPI _CST.
Instead use this map:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Change-Id: I37eb02bf9555c74e957316a1ba9778eb2b6ee128
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62898
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4377
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The management engine is occasionally hanging the system on resume
when it is accessed. Since we actually don't need to do anything
with it on resume it can be disabled early in the resume path and
avoid assigning resources just to remove them later.
suspend/resume on falco and check /sys/firmware/log
to ensure that device 00:16.0 is disabled early and that no
resources are probed or assigned and that the device init path
does not execute.
Change-Id: I35573681e3a1d43d816d24954842cbe9c61f3484
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The management engine is slow, requiring at least 500ms between
when the Dram Init Done message is sent (right after memory training)
to when the MBP will report that it is successfully cleared and
that the ME can finally be sent the EOP message.
Currently this is adding 100-150ms to the boot time. If we defer
waiting for the MBP Clear indicator until the finalize step we
can gain back that lost time.
boot on falco with SMI debugging enabled to
ensure that the ME is locked down in the finalize step:
Finalizing Coreboot
SMI# #0
SMI_STS: PM1 APM
ME: MBP cleared
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
Change-Id: Icab4c8c8e00eea67bed5e8154d91a1eb48a492d1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4375
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There are specific programming requirements for the usb3 ports
on all LynxPoint chipsets when transitioning to D0 or D3.
LynxPoint-LP has additional workaround steps needed involving
resetting the disconnected ports when transitioning to D0.
The workarounds are implemented in ACPI code so the controller
can transition properly into D3 at runtime.
Change-Id: I3b428562f48c9cb250b97779a3b2753ed4f81509
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4374
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This reverts commit ff81f50f0e4c068b64c4a5c7f5244196ecd24965.
Deferring this step until the finalize stage will allow us
to defer waiting for the MBP clear indicator and speeding
up the boot.
Change-Id: Ib8edffd06689e72875830cd68b5aedb7ac3b0559
Reviewed-on: https://gerrit.chromium.org/gerrit/62631
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4373
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The intel_ddi.c change I thought should be in but I don't see it. It just adds two functions back
that we need.
There are two new files for slippy annotated with comments about how it needs to evolve.
That said, this code has been tested on 3 different panels. Both dev and non-dev usages work.
physbase initialization to static value removed.
Moved spin calls to intel_dp_*
Change-Id: I0480af45c21c7dedcaff7e8be729f0eb554ec78a
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61136
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4370
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Peppy SPD table has 4GB configurations followed by 2GB configurations.
Current implementation does remapping to point 2GB configuration to the
same SPD index as the 4GB. This is different than Falco, which simply
duplicates the SPD data for all configurations. To simplify probing in
mosys, copy the Falco implementation of duplicating SPD data.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Idb185a437f3cf4f40d2dae1ae59c30235df8f489
Reviewed-on: https://gerrit.chromium.org/gerrit/61847
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-by: Jay Kim <yongjaek@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4369
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
When using RW firmware path the proper recovery reason can
be retrieved from the shared data region. This will result
in the actual reason being logged instead of the default
"recovery button pressed" reason.
1) build and boot on falco
2) crossystem recovery_request=193
3) reboot into recovery mode, check reason with <TAB>
4) reboot back into chromeos
5) check event log entry for previous recovery mode:
25 | 2013-07-15 10:34:23 | Chrome OS Recovery Mode | Test from User Mode
Change-Id: I6f9dfed501f06881e9cf4392724ad28b97521305
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61906
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4368
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The EC temperature sensors were renumbered and now PECI
is at index 0.
1) boot on falco
2) check /sys/class/thermal/thermal_zone0/temp
3) check 'temps' on ec console
Change-Id: Idde1457c42c80850b5b8ac22781060ed9b224d13
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61896
Reviewed-on: http://review.coreboot.org/4367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This may need further tuning but will start at 1.0%.
boot on falco and check /sys/firmware/log
localhost ~ # grep RTD2132 /sys/firmware/log
RTD2132: Enable 1.0% Spread Spectrum
I2C: 01:35 (Realtek RTD2132 LVDS Bridge)
Change-Id: I96e1c14dbc6a7bfaf1c8deb1806c48bf2fd3e32a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61895
Reviewed-on: http://review.coreboot.org/4366
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This driver allows the mainboard to enable spread spectrum
clocking at 0.5%, 1.0%, and 1.5% with devicetree settings.
Change-Id: I59c61e67aa8e951fd9904ad951deb6d0ba29669e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61894
Reviewed-on: http://review.coreboot.org/4365
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This is needed for SMBUS drivers to write to devices.
It was copied from existing intel southbridge driver.
Change-Id: Id0ce2393b2946a9c741413bca563a1a4dc0a4f5e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61893
Reviewed-on: http://review.coreboot.org/4364
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The drivers in the kernel expect the devices using gpios
to generate interrupts to be edge sensitive. Make it so.
Change-Id: I920ef621682d33ba081f737e97f0239f903db2f7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61678
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4361
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
SYS_TEXT_BASE is not used by any one. To prevent confusion when changing memory
layout, remove it from current configurations.
Change-Id: I15012b864bbb9c12003843b9b24ea64c91f4578b
Reviewed-on: https://gerrit.chromium.org/gerrit/61853
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/4371
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Make abuild -r work in more sitations (eg. xargs parallelization),
and make it not break junit output.
Also tell Kconfig to just overwrite the config file, instead of
atomically updating it, which help if coreboot-builds is on a
different filesystem (eg. tmpfs).
Change-Id: I2f4eedfd34ea6771732a60b38f1856056089be23
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4542
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Just like bluetooth and wlan it need to be enabled in EC.
Set the appropriate bit in EC if CMOS config says so.
Change-Id: Ia48ca3201f013d3b4c4153f32ff536e06b6a2f6d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4516
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Duncan Laurie