The PCIe WWAN module used on brya0 requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WLAN_RST#, then WLAN_PERST# in ramstage
BUG=b:187691798
Change-Id: I10f15a4dcfd86216c334fb24b4693ea250d35ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This GPIO is used to force the USB retimers on Type-C ports to stay in a
powered state and can be used e.g., during a firmware update to the
retimer to force power on even when no device may be connected to the
port. However, its power rail is controlled elsewhere and coreboot is
not applying a FW update, so this GPIO should be driven low instead.
BUG=b:193402306
TEST=compile
Change-Id: I976a0b8252b31aacef476d5ee4bcf6b1ef2e79de
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Adds "add" command to elogtool. This command allows adding elog events
manually. It supports event type and, optionally, event data.
If the free buffer space is < 1/4 of the total space, it shrinks the
buffer, making sure that ~1/4 of the free space is available.
BUG=b:172210863
TEST=./elogtool add 0x17 0101
./elogtool add 0x18
Repeated the same tests on buffers that needed to be shrunk.
Change-Id: Ia6fdf4f951565f842d1bff52173811b52f617f66
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Updated return type as CB_SUCCESS and aligned indentation.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ifabe0508a37a841779965f4e38172f680e18d38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Add mipi panel support for wormdingler
- Add the following panel for wormdingler:
INX P110ZZD-DF0
BOE TV110C9M-LL0
- Use panel_id to distinguish which mipi panel to use.
- Setup panel orientation
BUG=b:195898400,b:198548221
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: I8cd28e024ecbfdcd473bc39efb529eb4aca1b5d0
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
2. Hynix H54G46CYRBX267
BUG=b:199032134
TEST=emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: If8b75f9ed4d789d6c9c4365c517358df8d6e55c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
touchpad:390kHz
codec:395.8kHz
BUG=b:199481261
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ifadc3d19eb57fe6f67504be154c30df7bc0fee71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
All variants originally had been changed to start with an arrow with
two spaces following it to line up with the platform name. A number
of recent platforms were added only using a single space. This change
updates them all to have two spaces so they line up again.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iab9e6207fff5a7d2f6d76e5ca33eeaca721a224f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FspMultiPhaseSiInit API was introduced with FSP 2.2 specification
onwards. EnableMultiPhaseSiliconInit is an arch UPD also introduced
as part of FSP 2.2 specification to allow calling FspMultiPhaseSiInit
API.
However, some platforms adhere to the FSP specification but
don't have arch UPD structure, for example : JSL, TGL and Xeon-SP.
Out of these platforms, TGL supports calling of FspMultiPhaseSiInit
API and considered EnableMultiPhaseSiliconInit as a platform-specific
UPD rather than an arch UPD to allow calling into FspMultiPhaseSiInit
API.
It is important to ensure that the UPD setting and the callback for
MultiPhaseInit are kept in sync, else it could result in broken
behavior e.g. a hang is seen in FSP if EnableMultiPhaseSiliconInit
UPD is set to 1 but the FspMultiPhaseSiInit API call is skipped.
This patch provides an option for users to choose to bypass calling
into MultiPhaseSiInit API and ensures the EnableMultiPhaseSiliconInit
UPD is set to its default state as `disable` so that FSP-S don't
consider MultiPhaseSiInit API is a mandatory entry point prior to
calling other FSP API entry points.
List of changes:
1. Add `FSPS_HAS_ARCH_UPD` Kconfig for SoC to select if
`FSPS_ARCH_UPD` structure is part of `FSPS_UPD` structure.
2. Drop `soc_fsp_multi_phase_init_is_enable()` from JSL and Xeon-SP
SoCs, a SoC override to callout that SoC doesn't support calling
MultiPhase Si Init is no longer required.
3. Add `FSPS_USE_MULTI_PHASE_INIT` Kconfig for SoC to specify if
SoC users want to enable `EnableMultiPhaseSiliconInit` arch UPD (using
`fsp_fill_common_arch_params()`) and execute FspMultiPhaseSiInit() API.
4. Presently selects `FSPS_USE_MULTI_PHASE_INIT` from IA TCSS common
code.
5. Add `fsp_is_multi_phase_init_enabled()` that check applicability of
MultiPhase Si Init prior calling FspMultiPhaseSiInit() API to
honor SoC users' decision.
6. Drop `arch_silicon_init_params()` from SoC as FSP driver (FSP 2.2)
would check the applicability of MultiPhase Si Init prior calling
FspMultiPhaseSiInit() API.
Additionally, selects FSPS_HAS_ARCH_UPD for Alder Lake as Alder Lake
FSPS_UPD structure has `FSPS_ARCH_UPD` structure and drops
`arch_silicon_init_params()` from SoC
`platform_fsp_silicon_init_params_cb()`.
Skip EnableMultiPhaseSiliconInit hardcoding for Tiger Lake and uses
the fsp_is_multi_phase_init_enabled() function to override
EnableMultiPhaseSiliconInit UPD prior calling MultiPhaseSiInit FSP API.
TEST=EnableMultiPhaseSiliconInit UPD is getting set or reset based on
SoC user selects FSPS_USE_MULTI_PHASE_INIT Kconfig.
Change-Id: I019fa8364605f5061d56e2d80b20e1a91857c423
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch selects SOC_INTEL_COMMON_BLOCK_TCSS from Alder Lake SoC
Kconfig and drops SOC_INTEL_COMMON_BLOCK_TCSS Kconfig selection from
specific mainboard (brya) to ensure all Alder Lake mainboards can make
use of common TCSS block.
BUG=b:187385592
TEST=Type-C pendrive/Gen-2 SSD detected as Super speed.
Change-Id: I85f6a967eb34ea760418131a9586bfdeb13c9b5d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch allows ADL-RVP mainboards to set AUX GPIO PADs based
on the board id value.
Various ADL-P and ADL-M RVPs SKUs demand different GPIO AUX programming
hence, this patch implements a helper function inside `adlrvp` mainboard
to override devicetree chip config.
Note: Different ADL-P/M SKUs (LP4/LP5/DDR4/DDR5) don't have dedicated
devicetree for overrides hence, board id is being used for unique SKU
identification.
Additionally, skip AUX GPIO PAD filling up for Windows SKUs.
TEST=Able to override AUX GPIO PADs based on ADL-P RVP board id.
Change-Id: I2f0a37c7a8bd69af715551df2a93e6eed89e954a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This function is "extracted" from cmd_clear().
This new function will be called from cmd_add(), and new command that
will be added in a future CL (see CL chain).
Additional minor fixes:
- calls usage() if no valid commands are passed.
- Slightly improves usage() output. Needed for cmd_clear()
BUG=b:172210863
TEST=elogtool clear
Change-Id: I0d8ecc893675758d7f90845282a588d367b55567
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 2eb100dd12 added PMC LPM requirements to the the PEP ACPI
objects, but it was not made clear that one of the pointer arguments to
the mentioned function is not supposed to be NULL and Coverity
complained. Make the intention clear by instead asserting that `info`
cannot be NULL.
Fixes: Coverity CID 1462119
Change-Id: I9e8862a100d92f4a7ed1826d3970a5110b47f4c4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change uses a static 8-bit counter in
`acpi_device_add_power_res()` to generate the name of power resource
object rather using a default name "PRIC". This makes it easier to
identify which power resource Linux kernel logs are referring to. If
more than 256 power resources are used in the system, then the counter
will wrap around to 0. However, 256 seems to be a large enough number
for the power resource count.
TEST=Verified that Power Resources are named as expected:
```
dmesg | grep ACPI | grep PR
[ 0.550921] ACPI: Power Resource [PR00] (on)
[ 0.869960] ACPI: Power Resource [PR01] (on)
[ 1.013973] ACPI: Power Resource [PR02] (on)
```
No new ACPI errors are seen in dmesg on brya.
Change-Id: Ia18f7177b03821ce0f8c989ae5d258f2f83517a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
copy existing QUP driver from /soc/qualcomm/sc7180 to common folder.
This QUP common driver provide QUP configurations, GPI and SE
firmware loading and initializations.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I95a0fcf97b3b3a6ed26e62b3084feb4a2369cdc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
SPI NOR size should match with coreboot ROM size. On QCOM Piglin board SPI
NOR size is 64MB and the default coreboot ROM size is 8MB. So, update the
coreboot ROM size to match with SPI NOR size.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board and checked
basic boot up.
Change-Id: I78f3f402b383bbad303f26c31d3d973c5f20d172
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Buggzy's panel is oriented with its "right" side facing upwards, therefore
the firmware screens in depthcharge were incorrectly rotated. This patch
changes the orientation of the framebuffer provided by the FSP.
BUG=b:194967458
BRANCH=dedede
Change-Id: I4a5fbfcfc1c362da1bddd23c7d132416db3691c9
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
When the FSP driver fills out framebuffer information for the coreboot
tables, it assumes the orientation is always normal. This patch provides
a field for a mainboard to override the panel orientation from the
default (LB_FB_ORIENTATION_NORMAL). Later patches will have the FSP
driver use this value when filling out framebuffer information.
BUG=b:194967458
BRANCH=dedede
Change-Id: I559b3d6a076112a1c020ce5e296430d7ccba9ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add igd device name in soc_acpi_name(), and src/drivers/gfx/generic
can generate device in GFX0 scope in ssdt.
BUG=b:198188272
TEST=emerge-brya coreboot and check ssdt.
Change-Id: Id0c50254a8a25b47368e932c99243f4f02250b82
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Updating from commit id 4423276b:
2021-08-31 17:41:34 +0000 - (crossystem: add a hwid override mechanism from chromeos-config)
to commit id c5a482ed:
2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven)
This brings in 10 new commits.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I67d4bfa182eae98bb23ae487f117c991502b66ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Currently, check_boot_mode is called after vb2api_fw_phase1, which
makes verstage_main exit before reaching check_boot_mode if recovery
mode is manually requested. Thus, recovery mode isn't able to test
whether VB2_CONTEXT_EC_TRUSTED is set or not.
This patch makes verstage_main call check_boot_mode before
vb2api_fw_phase1 to fix the issue.
BUG=b:180927027, b:187871195
BRANCH=none
TEST=build
Change-Id: If8524d1513b13fd79320a116a83f6729a820f61f
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
CB:57324 moved panel orientation from panel_serializable_data to the
responsibility of the mainboard, but in parallel to that patch we landed
support for some new panels on the Trogdor mainboard that should be
pointing LEFT_UP. This patch fixes up the panel orientation for those.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I416b6c8804a88b36f723c4690ed78aff928a0f8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
There's dead links, CorebootPayloadPkg was replaced by UEFIPayloadPkg,
the development procedures are severely out-of-date, the only FSP 1.1
platform is Braswell (which is no longer actively developed), and the
pages don't appear in doc.coreboot.org (which uses Sphinx to generate
HTML pages from .md files). Oh, and it doesn't seem to have a license
associated to it.
Get rid of outdated documentation.
Change-Id: If359f554e85d32cdb65c3d928b5155db30bc40a5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Update audio FW config based on the schematic carbine_adl-p_evt_20210901.pdf
BUG=b:199180746
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I4f8ee1a97dd92c7aa0131cd0a77b05f851a26b05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57529
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on latest schematic (0903) update the GPIO table.
BUG=b:197308586
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie79ba14859f7fa4ea66a0f0d58287f4515d01baf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
https://tech-docs.system76.com/models/lemp10/README.html
Tested with TianoCore (UefiPayloadPkg).
Working:
- PS/2 keyboard, touchpad
- DIMM slot and onboard RAM
- Both M.2 NVMe SSDs
- MicroSD card reader
- All USB ports
- USB-PD
- Webcam
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- HDMI output
- DP over USB-C output
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone/microphone jack
- S0ix suspend*
- Booting to Pop!_OS Linux 21.04 and Windows 10
- Flashing with flashrom
Not working:
- S0ix when a device is attached to the TBT port
Change-Id: I15f7a3b6e9af07fcfde9a71d3f4a84ed625159b7
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fixes:
27c51a0 ("Revert "soc/intel/broadwell/pch: Replace ACPI device NVS"")
which reverted the removal of device NVS, but was not boot tested on any
Broadwell Chromebooks. It was recently discovered that the DNVS
object was not being loaded, due to a weak function setting the size
as zero not being defined for the platform/soc. Add the missing
overloaded function and required headers.
Test: build/boot google/auron variants LULU ans SAMUS, verify
touchpad functional and no ACPI errors in kernel boot log.
Change-Id: Icd317d117dbb068bb6da80fe56c06c0267c7b2ae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
1. The video output now works correctly with Intel IGD (tested with
TianoCore, edk2-stable201903-3392-gf7fe27d686).
2. The kempld EC driver now supports GPIO configuration since
commit 9941e5a5e6 (ec/kontron/kempld: Add minimal GPIO driver).
3. CorebootPayloadPkg is practically dead by now, so delete the comment
about the problem with it.
Change-Id: Ic216c3437b2670638c845ee8964f831b80e18fce
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57461
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some variants may require more complex power sequencing than can be
accomodated with just 2 GPIO tables, therefore introduce one in romstage
as well.
BUG=b:187691798
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7a63a2ee2cd036b9ae5822be9c87d8a026a54922
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Install both versions of UEFITool, the one with the old engine and the
new one.
It's not possible to use both packages in the same environment, since
there is a collision between the names of the binary files. To make sure
a specific package is used, a new environment needs to be spawned with
the following command:
$ nix-shell -p <package_name>
The UEFITool binaries can be executed from the shell then.
Change-Id: Ia5d679c6e7cd01c2ab819bd6c085596a926c494d
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
gimble only uses one WiFi SAR table, contained in a file named wifi_sar_0.hex
BUG=b:189068477
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ied030b79183cc6f962674260e7a82a7261b317ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57616
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes a few minor CBFS parsing edge cases that could lead to
unintended behavior: the CBFS attribute parser could have run into an
infinite loop if an attribute's length was (accidentally or maliciously)
invalid. A length of 0 would have caused it to read the same attribute
over and over again without making forward progress, while a very large
length could have caused an overflow that makes it go backwards to find
the next attribute. Also, the filename was not guaranteed to be
null-terminated which could have resulted in out-of-bounds reads on a
few error messages.
Finally, clarify the validity guarantees for CBFS header fields offered
by cbfs_walk() in the comment explaining cbfs_mdata.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie569786e5bec355b522f6580f53bdd8b16a4d726
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
This patch adds a new variant called kingoftown.
it's clamshell only, no FPR, eDP panel.
BUG=b:198365759
BRANCH=master
TEST=make
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I648664c50dfad11530a854f574f39264158b44e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This is no longer needed, since now this parameter is already set using
the ONBOARD_VGA_IS_PRIMARY config [1].
[1] commit 1a4496e79f
Change-Id: I368fa5d13615dc4ee37db596cb6a5eef993fc220
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tim Wawrzynczak