This patch enables customized NIC leds as follows:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:65437780, b:68284778
TEST=Make sure the registers are programmed as expected and observe the
LEDs are behaving as expected. Perform suspend/resume test and the
LEDs are still working as expected.
Change-Id: I9bb1367a4c742c2755d620e14ee6dfe70ee7f34b
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This compares to the acpi directory in other variants.
BUG=b:68293392
TEST=Build and boot kahlee
Change-Id: I05d402995b280d6f020bc2575063dbffefa30670
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Even though this GPIO isn't used for Kahlee, it needs to be defined
so that the weak version of the variant_board_id() function can
compile.
BUG=b:68293392
TEST=Build and boot kahlee
Change-Id: Ia8daf70fbafe02ec37c6b5eb8421cdb11de3be8b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that recovery button has been enabled through cr50,
we can add VBOOT_PHYSICAL_REC_SWITCH config and treat
the recovery button like on any other chromebox.
BUG=b:37751915, b:63893483
BRANCH=None
TEST=With DUT in normal mode, boot into recovery, press ctrl+d
followed by pressing the recovery button. Should successfully
boot into dev mode.
CQ-DEPEND=CL:737477
Change-Id: I72fb42508083295e317dd06900796dc0cda753f6
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22368
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Nautilus board uses Dialog da7219 headset codec,
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
Removes unwanted DMIC blob pick for nautilus
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on headset and recording on headset mic
Change-Id: I104889f54da1de38854bcb72aabbc88b739d6c09
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since we move from cannonlake U DDR 4 platform to cannonlake U LPDDR4
platform, it is also critical to revisit the GPIO settings as they are
different. Remove unused GPIO setting for old platform, and clean up the
native function definition. PAD_CFG_NF can only select NF1,NF2 ..., set
to GPIO mode is illegal.
TEST=Boot up in chromeos successfully.
Change-Id: I0022b791bd8459ea2afdcd0241b603ce81408785
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
SCI trigger logic had to be inverted.
This patch enables the system to wake up from S3 when lid is opened
when the system is in suspend state.We are trying to match what a
external EC card running ChromeEC FW is sending on the signal.
TEST = Verified that system wakes up from S3 on toggling lid switch
back to open state.
Change-Id: Ib42a38088ee028eddc6769921b0552c569da25a9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For internal measurements this mainboard needs a marking inside the NC
FPGA when coreboot is ready and payload has been loaded.
Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
RISC-V is moving towards OpenFirmware-derived device trees, and the old
functions to read the config string don't work anymore. Use dummy values
for the memory base and size until we can query the device tree.
Change-Id: Ice13feae4da2085ee56bac4ac2864268da18d8fe
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On older Grus, GPIO0_A2 was an audio voltage rail enable line. On
Scarlet, we instead moved the audio codec enable (previously on
GPIO1_A2) there. Unfortunately the code still had some hardcoded
leftovers that were overlooked in the initial port and make our speakers
smell weird.
This patch fixes the incorrect GPIO settings and adds the speaker enable
pin to the GPIOs passed through the coreboot table, so that depthcharge
doesn't have to keep its own definition of the pin which may go out of
sync.
Change-Id: I1ac70ee47ebf04b8b92ff17a46cbf5d839421a61
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
CQ-DEPEND=CL:*496012
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I580567decfccd78366c37181255015ac2cd76493
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/22306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
From what I can tell FILECODE isn't used at all in this file.
Remove it.
Change-Id: Ie88140e63a4917f470f42119c1fe4e8c7d2584ca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
In skylake based platforms, setting GPIO pad reset config
to DEEP will reset the gpio configuration across warm reset,
set it to RSMRST to preserve the configuration across warm resets.
Also, moving the configuration from early to late as appropriate.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I38940b7c7d71e60bf0e51d6978a00be148ad61bc
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adapted from Chromium commit 12ad5b5: Reks : override USB2 Phy settings...
Base on Intel recommendation, override following
settings for USB2 port 1/2/3 on BSW D-stepping SOC.
1. Set USB[1] register for right side to 7321
2. Set USB[2] register for left side to 7021
3. Set USB[3] register for CCD to 7021
Original-Change-Id: I04240a010e875f29c47f4fea83ff918f180b0273
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iabd6312576e9897315c4e4dbf19341380d9d1414
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit 6ee6f3d: Reks: To set the RX ODT limit...
Override RX ODT and DRAM geometry for Micron part MT52L256M32D1PF-107.
Use get_ramid() to determine if override is necessary.
Original-Change-Id: I41f3aba030a00152e1217533ef953338ac396605
Original-Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Original-Reviewed-by: Kane Chen <kane.chen@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Iea8c3c67e5afb21285dc15ad665474ad5f192423
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
ASL+ Optimizing Compiler/Disassembler version 20170831 shows the remark
below.
```
dsdt.aml 87: Method (_CRS, 0x0, NotSerialized)
Remark 2120 - ^ Control Method should be made Serialized \
(due to creation of named objects within)
```
So, serialize the method.
Fixes: commit 4a51ea8470 (google/kahlee: Add ASL for Elan touchpad)
Change-Id: I664f493318cbfd80d91565c0d29ec918278c4906
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/21901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Move files that are particularly specific to the mainboard into the
variant directory. Files that only have small areas of mainboard
specific pieces use #if to separate between the boards.
Add memory.c to split out the variant board id into a weak function.
Add baseboard/gpio.h to satisfy the build - this will be updated in the
next commit.
BUG=b:68293392
Change-Id: I7c1beb45f571f2547f3b5b0d7ec78923d0cec761
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The default setting for I2Cx is 400kHz. On this mainboard there is a
device on I2C0 which requires a lower clock rate to work correctly. For
this reason we set the frequency to 100kHz.
Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard has its own coreboot ready LED. The LED is switched on
via GPIO CNV_RGI_DT.
Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are PCI devices, which are connected to the PCIe
root port via a PCIe-2-PCI bridge. One of the devices only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 4 (Device 14.0).
The following routing is required:
INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA#
Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Current VBT setting for T8 is only 1ms which is under Innolux N116BCA-EA1
panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
CQ-DEPEND=CL:*493633
Change-Id: I7934b0f6d40b15796c55d360995c5eb0c5049222
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/22294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Leaving the wifi related gpios unmodified for now
due to FSP problem. If H0-H3 is configured as native mode
and GPIORXDIS, GPIOTXDIS bits in DW0 are cleared, it causes
FSP to assert when wifi module is attached. coreboot gpio
macros clears these 2 bits because they are suppose to be
"don't care" in native mode.
TEST=Boot to OS and verify wifi
Change-Id: Ica5e1c43802d04a9471cdfa0087e86f669122fff
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is to enable SPD word access to reduce boot time. It can save
80 ~ 100 ms per DIMM.
BUG=b:67021853
BRANCH=None
TEST=system boot, and boot time is reduced
Change-Id: Ic527a539ed634e15b939b18fff4b4e08ebb3ec57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For Raydium, export reset GPIO as well as PowerResource.
Let EN_PP3300_TOUCHSCREEN signal will goes to low at S3 mode.
BUG=b:67879912
BRANCH=coral
TEST=emerge-coral coreboot
Change-Id: Ibf501b40ecfc957fd8be7ebffd2357dfa0e07757
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/22252
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to have these separated.
BUG=b:64932381
Test=Build & Boot
Change-Id: I22898d3bf95d5e9a8fc2643bfccae1e2f5b29e44
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add new board librem15v3 as a variant of the librem_skl baseboard.
Changes from the librem13v2:
- Change board name and version
- Change GPIO A18, A19, A20, D9, D10 and D11 from NC to GPIO
- Enable PCI device 1c.4
- Change USB port definitions in devicetree
TEST: build w/SeaBIOS, boot PureOS on Librem 15 v3 hardware
Change-Id: I7c762a34f5b961c908e4a29ec331da4b0dea9986
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22048
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Convert the Purism Librem13v2 board to a variant setup,
in preparation of adding the librem15v3 as a new variant.
The 13v2 and 15v3 are nearly identical, so this minimizes new
code to add support for the latter.
Change-Id: I5d648cdb8f63c03de5474253203b3d0853673294
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22047
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It seems that recent changes in coreboot have fixed the raminit issues
on this board; the workaround of 10 ms delay after the S3 resume is not
needed anymore and can be removed.
Change-Id: If8fb97ecf3eb797f53270a053201fafd32031678
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/21485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Migrate the Librem13v2 from using FSP 1.1 to
the public/GitHub FSP 2.0 Skylake/Kabylake release:
- select FSP 2.0 in Kconfig
- adjust romstage/ramstage functions as required
- refactor pei_data functions
- remove VR_RING domain from devicetree (unsupported in FSP 2.0)
- add SataSpeedLimit parameter to work around power-related issue
when operating at SATA 6.0Gbps speed
TEST: build/boot Librem13v2, observe successful boot, lack of
SATA-related errors in dmesg.
Change-Id: Iedcc18d7279409ccd36deb0001567b0aa5197adf
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This commit just moves the vboot sources into
the security directory and fixes kconfig/makefile paths.
Fix vboot2 headers
Change-Id: Icd87f95640186f7a625242a3937e1dd13347eb60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Microcode blob has been updated, so update the length to match
Change-Id: I46ac10e5c6cd6492c98a7034649797f301101abc
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The USB settings were wrong in some places, or missing and the
USB_OC values were taken from the schematics.
Change-Id: I29b564a4161c486f5e8556b1726471bfa2351b7a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
