A video option rom must be added for UMA graphics support. It can
be extracted from the supplied UEFI BIOS.
ASRock E350M1 support is based on the AMD persimmon project. The
major differences are SIO model and DIMM SDP addressing. With this
coreboot and seabios, the board can boot DOS from a SATA drive and
can boot WinPE from a USB flash drive. I was unable to get
Windows setup to run.
The board has a socketed SPI flash BIOS chip and a serial port
header. The SIO is Nuvoton NCT5572D. Using coreboot's existing
Winbond w83627hf is a good enough match to get the serial port
and keyboard working.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6382 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The southbridge already provides hard_reset.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6378 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It currently supports:
- Sleepbutton
- AC state
- Battery state
- Interrupt routing
- Display Brightness control
- Hotkeys
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is incorrect, and will be replaced with proper ACPI for X60.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fixes abuild issues.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds support for Lenovo X60 series ThinkPads. So far, only X60s
(Model 1703) has been tested.
It's a basic patch without SMI and ACPI, as this makes it easier to
review. SMI and ACPI patches will follow.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code provides support for IBASE Technology DB-FT1 (AMD code name Persimmon) and AMD Inagua platforms. It is dependent on all other patches in this set.
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds a new src/ec subdir for embedded controllers (mostly found in laptops)
and converts Getac P470 and Roda RK886EX to use the new ACPI EC instead
of having their own copies of those functions.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6304 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smm-y wasn't required before, because udelay.c used to be #included from
various files in src/mainboard.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6303 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPT port. With the CMOS variable set, LPT is found by SeaBIOS,
with the variable reset, it's not.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the board. I thought we did this ages ago.
Also push CAR BASE further down so it won't conflict with a 32mbit flash part.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note:
1. bimini_fam10/Kconfig: Set GENERATE_MP_TABLE in Kconfig. This will make sure the
smp_write_config_table will run. Then intr_data will be written
into 0xC00/0xC01.
2. bootblock: Use PCI_DEV(0, 0x14, 3) instead of
pci_locate_device(PCI_ID(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB800_LPC), 0).
The pci_locate_device will cause the system crash.
3. fadt.c: Change fadt revision to 1. 3 will cause the linux hang. Why?
4. early_setup.c: pmio 0x65 has change its meaning.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6288 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board is 2MB and the entry point is somewhere in the middle. quite weird setup
http://www.embeddedarm.com/products/board-detail.php?product=TS-5300
We should probably wipe the board from the tree. It will not work anyways with
current coreboot and the architecture is kind of obscure.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6287 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6257 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6256 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on what the GPIOs are used for.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6254 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If a file "cmos.default", type "cmos default"(0xaa) is in CBFS,
a wrong checksum leads to coreboot rewriting the first 128 bytes
(except for clock data) with the data in cmos.default, then
reboots the system so every component of coreboot works with the
same set of values.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
select the right output device.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6252 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Correct default ROM image size for this board (512KB is correct).
- devicetree.cb: Add AUX I/O config (mainly GPIO settings).
This allows you to control the LEDs in the front panel and JP900/JP901
can be read.
- irq_tables.c: Rework PIRQ table to make more onboard devices work.
Also, avoid IRQ9.
- mainboard.c: Drop unneeded functions, everything is done in devicetree.cb.
Signed-off-by: Marc Bertens <mbertens@xs4all.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6247 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We did the same with other chipsets in r6150.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6236 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move CACHE_AS_RAM_ADDRESS_DEBUG #define to Kconfig, where it was renamed
to HAVE_DEBUG_CAR in r5898.
- Move QRANK_DIMM_SUPPORT to Kconfig, see r6028.
- Drop obsolete/unused COMPRESS, see r6145.
- Drop obsolete SET_NB_CFG_54, see r6086.
- Move SET_FIDVID/SET_FIDVID_CORE_RANGE to Kconfig, see r6077.
Actually, the default for SET_FIDVID_CORE_RANGE is 0, so drop it.
- Rename some GENERATE_* options to HAVE_*, see r6027.
- Drop "select CACHE_AS_RAM", this is now set in the socket, see r6151.
- Drop ACPI_SSDTX_NUM, the global default is 0 already.
- Random whitespace and coding style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6233 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6231 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to FG (FooGlue). As the GX2 has no VIP port.
-Change the Memmory setup MSR register names so they correspond better to the
databook. (Part1)
This is less confusing for beginners.
-Add a MSR printing function to northbridge.c like in the Geode LX code.
-Remove the AES register names.(GX2 has no AES registers)
-Delete some unused code.
-Clean up GX2 northbridge code to match Geode LX code.
-Add missing copyright header to northbridge.c.
-Move hardcoded IRQ defining from northbridge.c to irq_tables.c .
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The intel/xe7501devkit is still broken, I think the (romcc) image is too big to
fit in the bootblock if CONFIG_DEBUG_RAM_SETUP is enabled. It would make sense
to convert all CPU_INTEL_SOCKET_MPGA604 to CAR, but I have no hardware to test.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
allocator. If that does not work out, they should be set in the code. Setting
them in Kconfig is the worst possible thing to do.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6213 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- nokia/ip530/devicetree.cb, southbridge/ti/pci1x2x/pci1x2x.c:
- Fix SMSC FDC37B787 name (was a typo).
- Disable PS/2 keyboard/mouse LDN, the IP530 doesn't have either.
- Fix typo: s/PCI_DEVICE_ID_TI_1420/PCI_DEVICE_ID_TI_1520/.
- All of these are confirmed by Marc Bertens on IRC.
- Fix a few CHIP_NAME HP board names.
- Random whitespace and coding-style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6212 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed for all Intel 440BX boards with 4 DIMM slots (such as this one).
Thanks Marc Bertens <mbertens@xs4all.nl> for bringing up the issue and
for the success report for this fix on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6207 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Simple devicetree.cb fix, tested on hardware using a PCI-E x16 graphics card.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6203 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Don't include cmc.bin to the build. It's required, but we don't ship it
- mptable's API changes a bit. Adapt.
- Fix ACPI for new iasl versions with improved code validation
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6199 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which uses it.
Compiles, but not boot tested lately.
Many things missing (eg. SMM support, proper ACPI, ...)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
