acpi_device_add_power_res currently generates a `_STA` method hardcoded
to ON. This change enables the ability to generate a `_STA` method that
queries the status of the GPIOs to determine if the power resource is ON
or OFF.
BUG=b:184617186
TEST=Dump SSDT table for guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I91410556db002c620fd9aaa99981457808da93a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The new cezanne PSP release added support for these svcs. So add those
functionality back to cezanne psp_verstage.
BUG=b:187906425
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Id542f5ed0762f582ea966466d67ed938ecb9c1f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
GSC is connected with AP via i2c bus so we need to enable i2c in
psp_verstage.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5f7b73be67a692ea7de31ae53bd111d0e4b6998c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The custom bootsplash option only functions when using the UEFIPAYLOAD
payload option, so restrict visibility to when that option is selected.
Change-Id: If5fe46b629e5275da54a5e86465a68271110397b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Logging to coreboot cbmem, instead of a serial console, was
added to MrChromebox's uefipayloadpkg branch. Add a Kconfig
option to enable this, and restrict it to the UEFIPAYLOAD
payload option, since this feature does not exist in upstream
edk2.
Change-Id: Idef125235dc7ba885eb22ac69c6f752588a9e295
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
IO MWAIT redirection is disabled, which means reads to the P_LVL2 and
P_LVL3 "registers" will never produce any C-state transition requests.
Moreover, the register resource descriptors for all reported C-states
use the FFixedHW address space, not I/O.
Change-Id: I026835dd24d7ac1e1bae2d851e011e1670abaad4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Even if IO MWAIT redirection were enabled, the base address is wrong.
Moreover, the register resource descriptors for all reported C-states
use the FFixedHW address space, not I/O.
Change-Id: Ic2faaafbe4928994aeeab8098d8e0fb6703d203d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The MSR only needs to be set when IO MWAIT redirection is to be enabled.
Change-Id: Ie856086babe4dadc690f701bd90a7bbac88cb4ad
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
These PCH PCIe ports are used and should be enabled.
Resolves: https://ticket.coreboot.org/issues/311
Change-Id: I26ace6e043c7c66f8944f0986923014703423b8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Looks like the comments were derived from a preproduction board's
schematics. Production boards use a different port mapping.
Change-Id: I40c267ff048959b131c22c07695212e8bd90c3f4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
bin/{foo,bar,baz} can fail if one of the files doesn't exist (depending
on the shell in use). Instead, cd into the directory and list the
files individually.
Change-Id: I042b2e45fded1b63551d8e65ead2a7bbbf96b1e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
shadowmountain board variants.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: I2b769d653ad8ad8ff069a0787d00ff33ead5c912
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
different adlrvp boards.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: Ib9e82d953416c076588974f3167d00ae96f01bb5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add IDE-R and KT device to chipset.cb and leave it off by default.
Change-Id: Iaa51e3dc107eb3f06ad7b2aad72a6bc112999d98
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
On Chromebooks the RAM code is implemented by the resistor straps
that we can read and decode from ADC. For Cherry the RAM code can be
read from ADC channel 2 and 3.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4f28bc1c567cb886bd90d930219981a6206b9bb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
This patch adds support for SPM. This adds 43ms to the boot time.
TEST=program counter of SPM is correct value after booting up.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5f17f6d51fc9ad2d23c71c3c5cd29fdc777dc071
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55154
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 2e665eb8da.
Reason for revert: Was submitted too early and out-of-order.
Change-Id: I119b7a81b849bbe3424d73d5fdf9b55481444686
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54971
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch makes coreboot set VB2_CONTEXT_EC_TRUSTED based on the EC"s
boot mode. Vboot will check VB2_CONTEXT_EC_TRUSTED to determine
whether it can enter recovery mode or not.
BUG=b:180927027, b:187871195
BRANCH=none
TEST=build
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I9fa09dd7ae5baa1efb4e1ed4f0fe9a6803167c93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
I2C4 is not used pn Brya hence make below changes:
1. Disable it in SerialIoI2cMode.
2. Remove I2C4 config in common_soc_config.
TEST=Make sure FSP is not programming I2C4.
Change-Id: I94c72b7fac9d8a001913b5faa2c0c8a3e8b701e9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for LabTop Mk III (kblr) and LabTop Mk IV (cml)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iffa6061b0e600880b0c93746f35b1731e4841e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Support for Star Labs labtop series EC
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I1967f7c4a7e3cab714f22844bf36749e0c9652b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This ACPI interface is required by e.g., the intel/common/pcie/rtd3
driver, which is used by some alderlake boards.
BUG=b:190080798
TEST=disassemble SSDT and find \_SB.PCI0.PMC.IPCS
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I59eae47e623587d35e394c9bff21481fcad2d6b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55172
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add common gpio functionalities across qualcomm soc targets.
This common gpio driver would allow the consumers to be able to
configure gpio function, set/get gpio direction as input/output,
configure the gpio as pull-up/pull-down, configure the gpio as an
IRQ and also query the gpio irq status.
The GPIO pin definition would be SoC specific.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ia672130c6ca938d9284cae5071307637709480d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55076
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the OS provides its own driver for the I2C controller it can
choose to use a bus speed other than the one used at coreboot runtime.
In this case it would be good to provide a way how the needed bus
timings are communicated to the OS, since these are very board-specific
and there is no way that the OS can know them other than read the
appropriate ACPI reported timings.
This patch adds some code to report additional bus speed timings if
there are some defined in the devicetree.
Change-Id: If921e0613864660dc1bb8d7c1b30fb9db8ac655d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch adds the ACPI hardware error source table (HEST) support.
This involves a few different parts: (1) The ACPI HEST table which is filled
with the appropriate fields (2) Reserved memory which is used by runtime
SW to provide error information. OS will not accept a HEST table with
this memory set to 0.
The ASL code to enable APEI bit will be submitted in a separate patch.
Tested on DeltaLake mainboard with following options enabled
SOC_INTEL_XEON_RAS
After boot to Linux, the following will show in dmesg:
HEST: Table parsing has been initialized
Change-Id: If76b2af153616182cc053ca878f30fe056e9c8bd
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This reverts commit 255b6f8646.
No longer needed after commit dd01e0131a
(Revert "util/lint: Add test for documentation in util dirs") has been
submitted. Plus, `util/vboot_lib/description.md` gets deleted whenever
one runs `make -C util/cbfstool clean`, which is rather annoying.
Change-Id: Ic93da096b6186d1d2af12243a74ec597694960c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55162
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for loading SPM firmware from CBFS to SPM SRAM.
SPM needs its own firmware to enable SPM suspend/resume function which
turns off several resources such as DRAM/mainpll/26M clk when linux
system suspend.
TEST=program counter of SPM is correct value after booting up.
Change-Id: Ia0f9b9f86e44b293c1cc47213946304c64aea75e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55140
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Raul E Rangel