Assembled SoC part does not have integrated graphics.
Change-Id: I5d157063cd850d343df73d448e6904c188a09730
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18150
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Initial work based on db-ft3b-ls and code released by Eltan. Board
boots with some limitation.
Now the AGESA binary is harcoded and board specific until it's fixed
by the SoC vendor.
memtest86+ from external repo skips looking for SPD on SMBus, which when
performed cause memtest86+ to hang. Still didn't tried whole test suit.
SeaBIOS 1.9.3 have some problems with USB which lead to no booting in
some cases. Full log:
https://gist.github.com/pietrushnic/787cbf63f610ff4f6b4ac13e5c20b872
SeaBIOS from PC Engines repository (https://github.com/pcengines/seabios)
works fine. Those changes are planned for upstream.
Information about obtaining and booting Voyage Linux:
https://github.com/pcengines/apu2-documentation#building-firmware-using-apu2-image-builder
Change-Id: Id23e448e27f4bba47b7e9e7fa7679e2690c6e4bc
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/14138
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Vendorcode always does PCI MMCONF access once it is
enabled via MSR.
In coreboot proper, we don't give opportunity to make
pci_read/write calls before PCI MMCONF is enabled via MSR.
This happens early in romstage amd_initmmio() for all cores.
Change-Id: If31bc0a67b480bcc1d955632f413f5cdeec51a54
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In RS485 mode RTS line acts as a transceiver direction control.
The datasheet is not very clear about the polarity but register setting
here is tested to drive nRTS line high when transmitting.
Also note revision of B of the super-IO has errata and 8N1 setting does
not work properly, you would need revision C of the chip assembled to
fix this.
Change-Id: I705fe0c5a5f8369b0a9358a64c74500238b5c4ba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14998
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Just the memory size, there is no strap to identify PCB revision.
Change-Id: I65b2f5b0ac6930bead60ea0a551f13a6bcab24c7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14997
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add APU1 prefix because Kconfig throws errors if we try to
define the same variables as choice-entry for APU2 board.
Change-Id: Ic071600dd88e391a8a278d63aad13abd01fd3c9d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14988
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
File buildOpts.c is a can of worms, pull platform memory
configuration in to OemCustomize.c. This array should be
assigned at runtime instead of linking a modified defaults
table.
Change-Id: I73d9d3fbc165e6c10472e105576d7c40820eaa6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are other things besides PCIe port configuration that
require board specific hooks.
Change-Id: I0923651487b9ed5f6f7569ce08e02d993fa5f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The two external USB ports and the internal USB header have overcurrent
protection chips with the low-active overcurrent signal connected to the
chipset.
The power-on default for this register disables the software detection
of overcurrent conditions.
After setting the register Linux correctly shows the overcurrent
condition in the kernel log (tested by shorting the 5v and gnd lines on
J14 / the internal USB header):
[ 2015.229921] usb usb1-port3: over-current condition
[ 2015.449925] usb usb1-port4: over-current condition
Simlar for the external ports:
[ 256.237916] usb usb1-port1: over-current condition
[ 256.458084] usb usb1-port5: over-current condition
Note that each signal is shared between two ports:
usboc0#: External ports (port1/5)
usboc1#: Internal ports (port3/4)
Change-Id: I02d498053b8ec61dc206e74a96c4a1dcfd4fae92
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/14084
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The newer versions of IASL are unhappy when an operator
has the same object as both source and destination.
The warning can be completely disabled with a command
line argument, but in general, I'd really rather not
just disable warnings.
The bits in this register are write 1 to clear, so reading and
writing the same register is what we want to do. Instead, store
it in a temporary register then write it in a second operation.
Fixes warning:
dsdt.aml 1396: Store(PWST, PWST)
Warning 3023 - ^ Duplicate value in list
(Source is the same as Target)
Change-Id: I52d73d4431db237be83016d67cd397f31b53d9c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _HID was present for the top level BTNS and LEDS Devices, but
was missing in the individual devices.
The alternative would be to supply the GPIO being used as an _ADR
object, but since it looks like the driver already has another
method of handling that, it isn't required.
Fixes these IASL warnings:
dsdt.aml 1522: Device (BTN1)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1567: Device (LED1)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1576: Device (LED2)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1587: Device (LED3)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
Change-Id: I67c48084a6ee2a104ffff2b5a986d24a51ee49e1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12582
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We've actually got more warnings now than when I first tested IASL
warnings as errors. Because of this, I'm adding it with the option
to have it disabled, in hopes that things won't get any worse as we
work on fixing the IASL warnings that are currently in the codebase.
- Enable IASL warnings as errors
- Disable warnings as errors in mainboards that currently have warnings.
- Print a really obnoxious message on those platforms when they build.
***** WARNING: IASL warnings as errors is disabled! *****
***** Please fix the ASL for this platform. *****
Change-Id: If0da0ac709bd8c0e8e2dbd3a498fe6ecb5500a81
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
only enable pcie gpp clocks when the corresponding clkreq pin is asserted
Change-Id: I7822d011bb94867d470c0194e6b652833c395cb2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12353
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
disable unconnected FCH clock outputs to save some power
Change-Id: Ib3efebb8656392d58d762c23827168017d273de8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12082
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
All the deleted mainboard files contain no code besides some print
statements denoting, that the init is executed.
If such statements are desired, this should be done in common code so it
does not have to be added to each mainboard.
Therefore, also delete files with just print statements.
Change-Id: I379e4b1e1b1725648c6231bc6954ac3cc655a596
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/12355
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Serial number is derived from the MAC address of first NIC.
Change-Id: I91e5555b462cca87d48fb56c83aedd1eb02eba62
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11901
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Do this to wipe error message and hexdump of SPD from console log.
Change-Id: I45ffcb1c80aecf43b79d93faedcd62c8f0023cb7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Value of tRFCmin was incorrectly using 2 Gigabit chip data.
There was no observed instability or bug reports because of this.
Change-Id: Ifa03b883afa5a304dd20caf3d4d0383c6cfebdb8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Inspired by the Sage source code (itself from coreboot).
Change-Id: I4864923166efb200882d895c572d1ee060c71951
Signed-off-by: Maxime de Roucy <maxime.deroucy@gmail.com>
Reviewed-on: http://review.coreboot.org/11730
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The thermal sensor interface exposed in function 3 of the northbridge is
a more convenient and faster way to access the processor-internal
thermal sensor than using the SMBus/SB-TSI interface from the FCH, see
the Family14 BKDG: "Tctl is a processor temperature control value used
for processor thermal management. Tctl is accessible through SB-TSI and
D18F3xA4[CurTmp]. Tctl is a temperature on its own scale aligned to the
processors cooling requirements"
Also on at least some of these boards the existing thermal zone is
broken and always returns 40C (the default value if the SMBus read
failed) because the SMBus muxing register (SmBus0Sel) is not set up
correctly.
Case in point: The fallback "smbus read failed" temperature is 40 C and
the the logs taken from the board status repository for the Asrock
E350M1 board all show: "ACPI: Thermal Zone [TZ00] (40 C)"
e.g.
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-5054-gf584218/2013-12-20T20:56:20Z/kernel_log.txt#l390
and
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-7030-g6d7de4f/2014-10-16T15:34:19Z/kernel_console.txt#l404
and
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-9989-gf2dfef0/2015-06-13T00:22:49Z/kernel_log.txt#l425
Example lm-sensors output with this patch on the pcengines APU1, on
Linux 4.1.0-rc8+ (wiht both CONFIG_ACPI_THERMAL and
CONFIG_SENSORS_K10TEMP enabled):
acpitz-virtual-0
Adapter: Virtual device
temp1: +54.0 C (crit = +100.0 C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +54.0 C (high = +70.0 C)
(crit = +100.0 C, hyst = +97.0 C)
Change-Id: Id9c5b783ba424246816677099ec6651814e59f21
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10940
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Provide ACPI devices with devicetree-compatible annotations for the
three leds and the button of the APU1, as well as the GPIO driver.
This will cause the Linux kernel to automatically load the following
modules:
leds_gpio (CONFIG_LEDS_GPIO)
gpio_keys_polled (CONFIG_KEYBOARD_GPIO_POLLED)
gpio_sb8xx (CONFIG_GPIO_SB8XX)
See
http://events.linuxfoundation.org/sites/events/files/slides/ACPI_vs_DT.pdf
and https://lwn.net/Articles/612062/ for some more information on how
the PRP0001 HID works.
To make this usable a Linux GPIO driver for the AMD chipset is also
required, which I am currently working on, but have not submitted
upstream yet.
Leds have been named after the convention in
Documentation/leds/leds-class.txt:
LED Device Naming
=================
Is currently of the form:
"devicename:colour:function"
For comparison, on an OpenWRT device:
GPIOs 0-21, ath79:
gpio-1 (tp-link:green:usb ) out hi
gpio-2 (tp-link:green:system) out lo
gpio-3 (reset ) in hi
gpio-5 (tp-link:green:qss ) out lo
gpio-7 (qss ) in hi
gpio-9 (tp-link:green:wlan ) out lo
gpio-18 (rtl8366rb ) in hi
gpio-19 (rtl8366rb ) in hi
On the apu1:
GPIOs 288-511, platform/PRP0001:00, AMD SB8XX/SB9XX/A5X/A8X GPIO driver:
gpio-475 (switch1 ) in hi
gpio-477 (apu1:green:led1 ) out hi
gpio-478 (apu1:green:led2 ) out hi
gpio-479 (apu1:green:led3 ) out hi
Change-Id: I956ee92d9d98ef27a83ccb30d314543bd8634f2c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10540
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The smbus.asl operation regions prevent the Linux i2c driver (i2c_piix4)
for this chipset from claiming the ioport ranges and thus it fails to
load.
The methods defined in smbus.asl are not used in the DSDT and also don't
exist in the DSDT of the vendor firmware.
In particular due to the following check in i2c-piix4.c will fail unless
acpi_enforce_resources=no is explicitly set on the Linux kernel
parameters:
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
Depending on kernel options the only error message printed is
ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B07 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0B (\SMB0) (20150410/utaddress-254)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
However since it does not implement a standard interface there is no
native ACPI driver for smbus.asl.
Change-Id: Id8401e8b36f0e2412d490a92c20540a04d853125
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10539
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Note: apu1c models do not support this. That we expose S3 in
ACPI table while it is not available, is a wider issue to solve.
Change-Id: I9b07550d0523593f51c1882a40cccd783115057b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10315
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Same comments were already removed for the latest board, the amd/lamar.
Change-Id: Ie244f838409c567c11f7444c9cf17de72e49dbb0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10283
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
These are alternative customer options connected to J19 header.
We need to avoid modifying devicetree.cb, so we fix devicetree
for the super-io device-enables at runtime instead.
Change-Id: I04a79974b9bdf52b09ffc1b1362e201eab1ee011
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10178
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These tables are not referenced anywhere, thus all
comments about adjustments are void.
Also drop stub AgesaReadSpd that is all commented out.
Change-Id: I12233ea0dc4baaf36a75f359c52cc59c9b6dad79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10143
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
This change switches all southbridge vendors and southbridges
to be autoincluded by Makefile.inc, rather than having to be
mentioned explicitly in southbridge/Makefile.inc or in
southbridge/<vendor>/Makefile.inc.
In order to be able to drop southbridge/amd/Makefile.inc, some
scattered source files had to be moved to a southbridge/amd/common
directory, in accordance to what we are doing on other architectures
already.
This means, vendor and southbridge directories are now "drop
in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree components to be
built with a given coreboot version (given that the API did not
change).
Change-Id: I79bd644a0a3c4e8320c80f8cc7a7f8ffd65d32f2
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/9796
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
echo is evaluated by a shell builtin producing non-binary
spd data of the form '-e -n \<byte>'. Correct this by
using printf builtin which does the equivalent and is
more cross platform friendly.
Boards changed:
gizmosphere/gizmo
gizmosphere/gizmo2
google/bolt
google/falco
google/link
google/peppy
google/rambi
google/samus
google/slippy
pcengines/apu1
Change-Id: Iefdaf59903b9682cc88c94fd991883b560616492
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9196
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
