Configure I2C high / low time in the device tree to ensure Touchpad
I2C CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
Touch Pad CLK: 389.2 KHz
BUG=b:202787528
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Change-Id: I0f9d062fc611de0062a39849aee1174268391682
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Since espi_util.c is also built in the case of verstage on PSP, we can
just add it to all stages.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I65e07c356aac73c5de2d9ce5582434872a223c19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The bits REMOTE_IRR and SEND_PENDING are documented as read-only,
and reserved bits should not be modified either.
Change-Id: I6bcb9eb990debe169340a0bfe662158b62a8f4dc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The bit LAPIC_SPIV_ENABLE returns 0 after reset even though
LAPIC has not been temporarily disabled.
Change-Id: Id261bc68fe9d1b1b0e5a3ef599a8f33a686d283b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Only the enable_lapic() part is required while doing
SMP init. Also disable_lapic() must not be called if
we rely on LAPIC for timer source.
Change-Id: Ib5e37c1a0a91fa4e9542141aa74f1c1876fee94e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
If the VGA BIOS file path for `VGA_BIOS_FILE` in a mainboard's Kconfig
does not exist in the coreboot tree (including submodules), drop it.
These files should be stored in the `site-local` subdirectory and the
paths specified for each board in `site-local/Kconfig`. For example:
config VGA_BIOS_FILE
default "site-local/x200_vbios.bin" if BOARD_LENOVO_X200
Note that this is just an example. There are better ways to structure
one's `site-local` subfolder. Using the `CONFIG_MAINBOARD_DIR` option
would be one of them, though variants may still need special handling.
Also, update autoport to not generate `VGA_BIOS_FILE` defaults.
Change-Id: I1b5dfba035a42d7943f270f95fb7d32b285584d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
If available, use data from MEMINFO CBMEM table and saved handles
from type 17/19 tables to generate type 20 (Memory Device Mapped
Address) SMBIOS table.
Windows 10/11 and some other OSes use this table to report the total
memory available on a given device.
Change-Id: I2574d6209d973a8e7f112eb3ef61f5d26986e47b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58271
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
microcode_file could be NULL and passed to get_microcode_size,
this was detected by klocwork scan.
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: Ibb3d49ab18d8c26bbf5d6bf6bdf1bf91137f5736
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There's no need to mask out bit 11, as it is unconditionally set. For
some reason, this changes the resulting coreboot image. Also simplify
another PCI operation with a redundant AND-mask.
Change-Id: I5492acd5f9c61db83a07ce7c1f6b887768c3eadf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
variant_has_pcie_wwan helper returns true if gpp_bridge_2 PCIe engine is
enabled. On some variants, this engine is used by storage controllers.
Fix it by adding a weak override that returns no PCIe WWAN by default.
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that PCIe WWAN is
enumerated on boards where it is stuffed.
Change-Id: I07b9dd8fc5c8c3e1557f9268c1176d4a3cade1af
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Scout only uses I2C 1, 2, and 3 in DVT units. This removes extraneous
I2C configuration copied from Puff.
BUG=b:202195805
TEST=Boot scout, verify no more errors due to missing I2C devices
Change-Id: Ide70a53e83b3e14540873062e3bef24d1134d2e1
Signed-off-by: Matt Ziegelbaum <ziegs@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
S3 is not currently functional on Guybrush. Remove support from ACPI.
BUG=b:202401767 b:181766974
TEST=Boot Guybrush
Confirm 'deep' is not in /sys/power/mem_sleep
Confirm S0ix suspend/resume still works
BRANCH=None
Change-Id: I9ed3e051f7f2e411670649ac2528a6f40229bdc6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Files used by this test are in: tests/data/lib/lzma-test/
file.bin - files with uncompressed data
file.lzma.bin - files with LZMA-compressed data from file.bin
How to prepare compressed file:
util/cbfs-compression-tool compress file.bin /tmp/file.lzma.bin lzma
dd if=/tmp/file.lzma.bin of=file.lzma.bin skip=8 ibs=1
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Id75e0b41991382d4c391b031862106de58eacdf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
`cse_fw_update()` is currently checking whether an update is required
by comparing versions once and then again comparing versions later in
`cse_is_downgrade_instance()` to determine if the update is an upgrade
or downgrade. Additionally, if CSE RW partition is corrupt (determined
based on `cse_is_rw_bp_sign_valid()`), `cse_is_downgrade_instance()`
ends up using the corrupted version information to determine if it is
a downgrade instance.
This change reorganizes the firmware update checks to return different
status values:
1. CSE_UPDATE_NOT_REQUIRED: No update required. Versions match.
2. CSE_UPDATE_UPGRADE: Update required and it is an upgrade.
3. CSE_UPDATE_DOWNGRADE: Update required and it is a
downgrade (requires data clear).
4. CSE_UPDATE_CORRUPTED: `cse_is_rw_bp_sign_valid()` failed and hence
requires data clear.
5. CSE_UPDATE_METADATA_ERROR: Unable to read CSE metadata from CBFS.
This change also prepares the file for follow up changes which
completely drop cse_rw_metadata structure.
BUG=b:184892226
Change-Id: Iabecab8e373e65a11ba7fe1bfc125467571a0588
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58157
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently WWAN_AUX_RST_L is in S5 domain and does not get asserted on
S0i3 entry. Based on the schematics, the pull-down on that signal leads
to 10 mW power leakage on S0i3 entry. Assert the signal on S0i3 entry to
achieve some power savings and de-assert it on S0i3 exit.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the signal gets
asserted on S0i3 entry and de-asserted on S0i3 exit. Trigger
suspend/resume cycles and ensure that the WWAN module is enumerated
after each cycle.
Change-Id: I43c8655ee5209779748e4365db973e094cb08aca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58275
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to handle S0ix entry and exit notifications by adding the
corresponding _DSM functions. The function indices are chosen based on
the Modern Standby BIOS Implementation Guide 56358 Rev. 1.04. Inside
the notification functions perform any mainboard specific S0ix entry and
exit actions.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the notification
functions are invoked on S0ix entry and exit. Perform suspend/resume
cycles for multiple iterations.
Change-Id: I3014551f6e281d466628559453a0141a3dd6abad
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58274
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct the PCH serial IO settings, suitable for this mainboard.
Change-Id: I3c9915b2d52fbc6a15ac1e68c77bfb3983f7b1cd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Correct the USB settings, suitable for this mainboard.
Change-Id: I691d91d2a76e27b8efdc18eeae737a78e9ae38fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard has its own coreboot ready LED. The LED is switched
on via GPIO GPP_F20.
Change-Id: I3570d691e90d2cb6e11b856b876f0327da118522
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Enabling clock gating for CGPLL to lower power consumption in S3
and S0i3 states. See also: Cezanne PPR chapter 7, rev 3.03.
BUG=b:185273565
TEST=iotools mmio_read32 0xfed80e2c and 0e30 show clk gating
enabled and suspend_stress_test works.
Change-Id: I33cbdeec62e49db90b680da37e5028df03a9c015
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Init overridetree based on the schematics.
Refer to brya0/overridetree.cb to update the settings of the devices
including DPTF, WIFI, NAU8825 and etc.
Refer to kano/overridetree.cb to update the SSD settings (pcie4_0).
TODO: DPTF and USB positions will be further updated later.
BUG=none
TEST=Build Pass
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I30d26a47fe93736c63b578c9180b148ef73e8b9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
HPD event may not be ready when configuring TCSS mux for DP,
check if any DP device is connected and wait for HPD ready before
TCSS configuration. Remove unnecessary dependency on mainboard
functions, use generic interface which provides USB-C mux
operations.
BUG=b:192947843
TEST=select ENABLE_TCSS_DISPLAY_DETECTION in Kconfig.name for
Brya. Build coreboot and update your Brya. Boot Brya with USB-C
display connected, you should find `HPD ready after %lu ms` and
`Port C%zd is configured to DP mode!` in coreboot log. Display
should show screen in developer mode or recovery mode.
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: Ia7e6dd952d3183ecb76de6d4887ee573ef89bb50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Currently override speed config is applied only for non EM100 cases.
For EM100 case, override speed board version defaults to 0 leading to
"comparison of unsigned expression >= 0 is always true" error. Fix this
error by defining the override speed config for both EM100 and non-EM100
use-cases.
BUG=None
TEST=Build Guybrush for both EM100 and non-EM100 cases.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id8ee7b01c69c4555d6e6a7b0d5f095ea3aaf3405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58309
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
P_BLK is legacy and superseded by ACPI _CST. Also, the implementation
for most platforms in soc/intel is broken. Thus, drop it.
For APL the IO redirection is kept since it's used as replacement for
the broken MWAIT instructions.
Change-Id: I489aa7886dd9a4c1e6c12542bc2a1feba245ec36
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I0295bac619af45a0d82da2bf39985c8bdcb77d5e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I8ad773d1c616b746235ec67b98b83c5910464140
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add support to override SPI fast speeds based on board version from both
bootblock and verstage. Overrides apply for Guybrush only and SPI speed
is overridden from 66 MHz to 100 MHz starting board version 4. This will
help to improve the boot time on board version by ~60 ms and still allow
the old boards to boot with 66 MHz.
BUG=b:199779306
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5bf03ab8772f27aca346589e9c5662caf014d0d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add support to override SPI ROM fast speed based on board version. This
will allow boards to start at lower speeds during bringup and then
switch to higher speeds after assessing the signal integrity. Also
implement a default no-op override.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia8ff3b3bdb53fee142527ae63aa7785945909304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Currently all SPI speed configurations are done through EFS at build
time. There is a need to apply SPI speed overrides at run-time - eg.
based on board version after assessing the signal integrity. This
override configuration can be carried out by PSP verstage and bootblock.
Export the APIs to set and read SPI speeds from both PSP verstage and
bootblock.
BUG=None
TEST=Build and boot to OS in guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I281531e506b56173471b918c746f58d1ad97162c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
eSPI is setup in two different locations in bootblock depending on early
port80 routing configuration. Also eSPI is setup in PSP, if verified
boot starts before bootblock. Consolidate all the scenarios by
initializating eSPI very early in fch_pre_init if verified boot starts
after bootblock and eSPI is enabled.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Icfeba17dae0a964c9ca73686e29c18d965589934
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the GPIO mux/control MMIO regions are within the ACPIMMIO region,
we need to call enable_acpimmio_decode_pm04 here first so that accessing
the GPIO registers will work.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I4bc076261c72cf999a5f2464b74cff6bf694d473
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: I82f8e6e5f8ccb7f8246cae45a01a3ddd5f2966f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58244
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: If457f4a096cd63038bf6b40552aa3caaba33d5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58243
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is the wrong register offset printed in the debug log when the
data register is written:
'lpc_tpm: Write reg 0x18 with 0xnn' should be
'lpc_tpm: Write reg 0x24 with 0xnn' for data FIFO access.
This can be confusing when searching for issues with the help of the
TPM debug messages since the code itself is correct. Fix this error.
Change-Id: Ic28ee5a07146e804574b887ea05c62e7e88e9078
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some poppy variants did not select a system type, which led to the
default desktop type being set. Select the best fit enclosure type
for each variant.
Alphabetize the variant-specific options for improved readability.
Change-Id: I7c23f8fa3ae1de67f7a68b8a4e9ec16c4e8044df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Make use of the newly introduced ACPI macros for CPPC table generation
that currently exists of a bunch of confusing assignments of structs
that only get partially filled.
Test: dumped SSDT before and after do not differ.
Change-Id: I844d191b1134b98e409240ede71e2751e51e2159
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
BUG=b:202480992
TEST=emerge-dedede coreboot
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I811f32defd50a940a09f238d38c962d2caf42855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
For 1 bit long bit fields an unsigned type should be used. In this case
uint32_t is used instead of a generic unsigned int for both consistency
reasons with the rest of the file and to clarify that the bits will be
packed into a 32 bit memory location.
TEST=Resulting image of a timeless build for google/guybrush results in
identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic630d1709174d90336746bc37da504437c12643c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Replace the dt option `PmTimerDisabled` with use of the Kconfig option
`USE_PM_ACPI_TIMER` for enabling/disabling the PM Timer.
A default value representing the prior devicetree value was added to the
boards system76/{lemp10,galp5,darp7}, so this change will not alter
behaviour.
Change-Id: If1811c6b98847b22272acfa35ca44f4fbca68947
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix include of nvs.h to reflect commit 661ad4666c (ACPI: Select
ACPI_SOC_NVS only where suitable); and re-add <device/pci_ops.h>,
removed in commit 0aad0531dc (util/autoport/bd82x6x.go: Drop unused
includes), as the generated early_init.c uses pci_write_config16().
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Change-Id: Ic1e97cfa7dce0e4d25f7a37c28d3635bdbf6c2a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Set PKG_CST_CONFIG_CONTROL MSR bit 15 to make bits 15:0 read-only.
Change-Id: Ia196906d3c2636742ae90160a224354e8df7863a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a space before the `*/` C-style comment ending.
Change-Id: Ic8928286c8237808b9e380e4393078792589615d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Ian Feng