Enable the GEO SAR feature for nocturne. OxM programs wifi_sar VPD key in factory.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:65155728
BRANCH=none
TEST= Set the wifi_sar VPD with below command (values are junk for test purpose only,
actual values would be set be OxM)
sudo vpd -f <coreboot.rom> -s wifi_sar=30313233343536373839303132333435363738393030313
24142433435364445463031324142433400364445463031323343444546303132333435
Flash the <coreboot.rom> and boot to kernel. Get ACPI table and WGDS would get created
with VPD values passed in.
Change-Id: I32ad591f15fdb34704c8d98d98646dfa2d8882ff
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Refactor GPIO code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Icdd1f2a1dd1bd64a7218bf9c63bd4a0af1acbcc0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This is based on the Grunt variant.
BUG=b:111607004
TEST=Build Liara
Change-Id: I8f23e972be0d1665c736d61621a0caaa4c4c5551
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This is based on the Grunt variant.
BUG=b:111606874
TEST=Build Aleena
Change-Id: I6fd42db6f9f309c3c375b670cd22f818555e4195
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
busty workloads like Octane, Aquarium on open yorp board with heat sink,
sometime CPU temperature spikes till 99 degree Celsius and DPTF
initiates system shutdown. With reference to previous APL/reef/coral
platforms, this updates 105 degree Celsius for the CPU critical
temperature trip value to avoid shutdown. This patch also updates power
limit1 value to avoid the abrupt thermal shutdown by DPTF.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Icd786d3c9b5f7c733dac3fd3e22579e2434058a6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We should use active-state power management where possible to reduce
power consumption during normal operation. Enable these options.
Linux does not seem to enable this for AMD, and the Intel code in coreboot
does enable these options.
PCIEXP_COMMON_CLOCK is enabled also, to follow how Intel does it.
BUG=b:110041917
TEST=boot on grunt, see that WiFi and eMMC still run OK
Change-Id: Ia7c711304ffe460a9fb0d4f654a51485958239ea
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27464
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This creates a meep variant for octopus.
The devicetree overrides are copied from yorp, otherwise everything
just defaults to baseboard settings.
BUG=b:111543000
TEST=None
Change-Id: I791f8d1589d7323fbe884dddf0f9d7362a41b9ac
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Keep the backlight off until it is needed.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen, not prior.
Change-Id: Ia1aba787734e2976146ecd305dd821f0b326f0db
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable the backlight in the OS callback to SMI for APMC. This keeps
the backlight off until the OS is ready to display something.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen
Change-Id: Idf32b1a3d45971883571a829a5c0c1f8563bb1f7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the mainboard resume function and __weak variant override.
Change-Id: I808734208bd1ce81428771ea203709b53db56cd3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
there are 3 thermal sensors and index is:
0: 1 Charger
1: 1 SOC
2: 0 CPU
it needs to adjust sensor to index 2 to have correct
CPU temperature.
BUG=b:111284412
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I27afb6c5b64b0c39d6db15e6c61ea16a1fda1ca3
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This device claims to run at 75MHz with dual read, but it is not always
reliable. Add an option to change the SPI flash speed to 16MHz, to avoid
any problems.
BUG=b:111363976
TEST=manually try to get my em100 running (it doesn't yet)
Change-Id: I78d3d32c467aac82c72d31c773bfb0f69808aed4
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This applied to AMD devices as well as Intel, although the mechanism is
different. Move the option to a common place.
BUG=b:111363976
TEST=USE=em100-mode emerge-reef coreboot
See that a message appears:
* Enabling em100 mode (slow SPI flash)
Change-Id: Iea437bdf42e7bc49b1d28c812bfc6128e3eb68bd
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Currently thermal event support can not be disabled at board level.
Define and dependent code are placed in same file.
Move define of HAVE_THERM_EVENT_HANDLER to mainboard file.
Change-Id: Icb532e5bc7fd171ee2921f9a4b9b2150ba9f05c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27415
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling of TBMC device on AP side requires corresponding support on the
EC side as well. Since not all octopus variants have tablet mode support
enabled, this change enables TBMC device only for phaser.
BUG=b:111264961
Change-Id: I1ce181baa8ebaff0a9d767e97ddc256eef9789e8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to get better performance, map dram as cached after dram ready
in romstage.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui. Need a futher check after dram
calibration code ready.
Change-Id: Ie541fe08ee1d5b260abbabc0a5c18fb04e602b9c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27304
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor MMU operation code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Id8173da0a02e57e863263fcd89c91a9c089e8a0f
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add an extra space after 8th value on each line to make it easier
to count the values.
Update the empty spd to remove two random 0x80 values.
BUG=None
TEST=None
Change-Id: If330dbf0c133f65aedddc58ecb351a80b0e45a05
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27423
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
According to sona thermal table, PL2 need to check cpu id.
And then set PL2 value.
BUG=b:110867809
TEST=The thermal team verify OK
Change-Id: I5759fb3c685e3d4eef1be054541f950843d19874
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This commit changes the uid and desc fields for the sx9310 entries
in the devicetree to be unique, and correctly identify the position
of the respective sensors.
Change-Id: I501df7d3349fdebc9673c9815f5b1b2458abac6e
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
We would use GPP_B20 instead of board id to determine nautilus SKU.
BUG=b:80052672
BRANCH=poppy
TEST=Verified the new coreboot could determine SKU correctly
Change-Id: I1978b544eef7a184a3da191306ee32d862fa8c36
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27220
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TPM config items added upstream before ready
SPI/TPM is not functional on Cheza yet
Change-Id: I302e00014dc31279fe2574765763ecdbf326b449
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/27213
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
