Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
These values in GNVS are written, but never read/used. aoac.asl contains
proper ACPI power management functions for the AOAC devices that
directly access the state from the device's registers instead of relying
on cached values in GNVS, so the corresponding GNVS entries can be
dropped.
BUG=b:161165393
TEST=Mandolin still boots and dmesg shows no new ACPI errors.
Change-Id: Iee78df215308bd9b656228be787fac121d10ca99
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44245
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reduces the differences between Lynxpoint and Broadwell.
Change-Id: I759aa98b80c70c5024213bd8795375061bdbbf10
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42622
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MSR macros were treated as memory addresses and the loops had
off-by-one errors. This resulted in a CPU exception before GETSEC, and
another exception after GETSEC (once the first exception was fixed).
Tested on Asrock B85M Pro4, ACM complains about the missing TPM and
resets the platform. When the `getsec` instruction is commented-out, the
board is able to boot normally, without any exceptions nor corruption.
Change-Id: Ib5d23cf9885401f3ec69b0f14cea7bad77eee19a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Some cases could not be factored out while keeping reproducibility.
Also mark some potential bugs with a FIXME comment, since fixing them
while also keeping the binary unchanged is pretty much impossible.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 does not change.
Change-Id: I27d6aaa59e12a337f80a6d3387cc9c8ae5949384
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42154
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCIe RPC (Root Port Configuration) straps will force-disable some root
port functions if some root ports have a width greater than x1. In two
cases, this affects the last function. The PCIe init code will never
finish configuring the root ports if that is the case: it assumes that
the last function will eventually run through the code, but it doesn't.
If PCIe initialization does not complete, pressing the power button will
not power off the board, unless it is held for about five seconds. Also,
Windows 10 will show a BSOD about MACHINE CHECK EXCEPTION, and lock up
instead of rebooting. Depending on the microcode version, the BSOD may
not be visible. This happens even when the root port is not populated.
Use the strap fuse configuration value to know which configuration the
PCH is strapped to. If needed, update the number of ports accordingly.
In addition, print the updated value to ease debugging PCIe init code.
Existing code in coreboot disagrees with public documentation about the
root port width straps. Assume existing code is correct and document
these assumptions in a table, as an explanation for the added code.
Tested on Asrock B85M Pro4, PCIe initialization completes successfully.
Change-Id: Id6da3a1f45467f00002a5ed41df8650f4a74eeba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44155
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's not missing, it's just not where one expects it to be.
Change-Id: I377b68cbdc9266048074dc326490750777a6fbf5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43291
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard has a 18-pin LPC header, where one can plug in a TPM.
Untested, as I don't have a TPM.
Change-Id: I14a159c373987d8b12fde18f327a9eb387c01de8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Soften the hard dependency on SOC_INTEL_COMMON_BLOCK_SA by allowing CF9
resets to be used in place of global resets. If both types of reset are
available, prefer a global reset. This preserves current behavior, and
allows more platforms to use the TXT support code, such as Haswell.
Change-Id: I034fa0b342135e7101c21646be8fd6b5d3252d9e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
RVP11 and RVP3 set it to zero, the other two omit the setting.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I6b393f0f2269f62b415456c17ba5962f46a1c5d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43909
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RVP8 does not set it, and the other variants set it to zero. So, factor
it out.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I67c958af2dc955d07b895dc93fbe2232dbd48d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43908
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow variants to override the SPD_SOURCE_PATH to allow supporting
different types of DDR.
BUG=b:163065661
TEST="emerge-volteer coreboot" and verify all variants build.
Change-Id: Id52e651848548a783d6d9f57e88f6099425b063e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
In 'bootblock/pch.c', clear PCI_COMMAND_MASTER (BIT 2) prior to
programming PWRMBASE and enable BIT 2 after programming PWRMBASE
along with PCI_COMMAND_MEMORY (BIT 1).
Also perform below operations
1. Use pci_and_config16 instead of pci read and write
2. Use setbits32 instead of mmio read and write
Change-Id: I7a148c718d7d2b618ad6e33d6cec11bd0bce0937
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch removes the unnecessary enforcement of MP PPI in ICL
in order to have parity with other IA-SoC.
Now it allows user to select USE_INTEL_FSP_MP_INIT if required.
TEST=Able to build and boot ICL platform with either USE_INTEL_FSP_MP_INIT
or USE_INTEL_FSP_TO_CALL_COREBOOT_PUBLISH_MP_PPI selected.
Change-Id: I25288a24cdf9dceec45a90e4e7233225a6cab508
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Decrease the SPI ROM size from 32 MB to 16 MB
BUG=b:58540772
BRANCH=None
TEST= build firmware and check the magolor bin size
Change-Id: Ie7ddf698fde1dbf663859d5654946bc08abe737c
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
People who know a lot more about electrons and stuff than I do tell me
that leaving a HiZ pin floating without a pull resistor may waste power.
So if we find a pin to be HiZ when reading tristate strapping GPIOs, we
should make sure the internal pull-down is enabled when we're done with
it. (For pins that are externally pulled high or low, we should continue
to leave the internal pull disabled instead.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1669823c8a7faab536e0441cb4c6cfeb9f696189
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44253
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alexandru Stan <amstan@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO_89 was marked as EN_DEV_BEEP_L in pre-v3.6 schematics, but it was
never really used on any of the zork variants. Starting with v3.6,
GPIO_89 is left unused in schematics.
This change configures GPIO_89 as PAD_NC in baseboard GPIO
table. Since EN_DEV_BEEP_L still needs to be driven high to allow
speakers to work, GPIO_89 is configured as PAD_GPO driven high on
pre-v3.6 schematics.
BUG=b:62108046
Change-Id: I026cd6cb598667ce6e115c3ec9357a6a56051d39
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44190
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds support for touchscreen power control using:
* GPIO_90 for trembyle based boards
* GPIO_32 for dalboz based boards
By default, baseboard tables configure these GPIOs as PAD_GPO driven
low and override trees expose these pads as enable_gpio to be used by
ACPI power resource.
In order to support pre-v3.6 boards, override tables configure these
pads as PAD_NC and drop the enable_gpio setting from device tree based
on board version.
BUG=b:161935640, b:162747210
Change-Id: Iba5e36b65b44ea11613b4d5fc8f13ce6433f83ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44193
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
v3.6 of reference schematics have switched the polarity of reset
signal to touchscreen controller from active high to active low. This
change updates the default configuration in baseboard gpio tables to
set the reset GPIO to output low and override tables in variants to set the
reset GPIO to output high. Additionally, devicetree by default exposes
ACTIVE_LOW configuration for reset GPIO. In order to support pre-v3.6
boards, reset GPIO is updated to ACTIVE_HIGH based on board version.
BUG=b:161937506
Change-Id: I092f274d8eb1920a1cd6d3eccbe8f26b0b28928a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
HP_INT_ODL is no longer connected to CODEC_GPI in schematic version 3.6.
Split variant_audio_update into update_dmic_gpio and update_hp_int_odl.
Changed GPIO_29 from PAD_NC to PAD_GPI in Trembyle. Changed GPIO_84 from
PAD_NC to PAD_GPI for Dalboz. Changed HP_INT_ODL to appropriate pin in
both boards devicetree.cb.
BUG=b:161938476
BRANCH=None
TEST=None
Cq-Depend: chromium:2335424
Change-Id: I05ffb063ab99823d07be6eaa911efbde3cc4ff55
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44157
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new ddr_memory_cfg structure to support both DDR4 and LPDDR4x
memory types.
Change existing variant code to use the new meminit_ddr() call
instead of calling meminit_lpddr4x() directly.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that
volteer still boots. NOTE that this only tests the lpddr4 side
of the implementation as I do not have a DDR4 board to test this on.
Change-Id: Id4bca2bfa97530f0d04a0e8d90f01b8281d2aea6
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Add a common routine meminit_ddr() that calls the appropriate meminit
routine based on whether the memory type requested is LPDDR4x or DDR4.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that
volteer still boots. NOTE that this only tests the lpddr4 side
of the implementation. I do not have a DDR4 board to test this on.
Change-Id: Ib2039eb89211efc48d10897eb679d05f567ae5a1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Newer boards have removed the second temperature sensor
and relocated the remaining sensor.
BUG=b:162909373
TEST=Confirm on hardware.
Change-Id: Ie41a57598b0c87a6632f4c55c0f60a94a89cae43
Signed-off-by: Andrew McRae <amcrae@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Coverity detects an integer handling issue with BAD_SHIFT. The inline
function log2_ceil(u32 x) { return (x == 0) ? -1 : log2(x * 2 - 1); }
could return -1, which causes shifting by a negative amount value and
has undefined behavior. Add sanity check for the acm_header->size to
avoid shifting negative value.
Found-by: Coverity CID 1431124
TEST=None
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ic687349b14917e39d2a8186968037ca2521c7cdc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
There's no `function 1` on the iGPU device for this northbridge.
Change-Id: I597446f703165447c3a0d0c1536583b08bc8450c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
We can use `decode_pcie_bar` instead, as other northbridges do.
Change-Id: I35bede573ef2635c54123f9e553003577ecd0ea7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Turn it into `decode_pcie_bar`, taken from gm45.
Change-Id: Id1c2cfbcac1a798d046beced790930511dc97972
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44121
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures that coreboot is able to take control of APs back
by doing a full AP re-initialization after FSP-S is done.
TEST=Able to see all cores available after booting to OS using below command
when coreboot is built with USE_INTEL_FSP_MP_INIT enable.
> cat /proc/cpuinfo
Without this CL :
shows only 1 core (only BSP)
With this CL :
shows all possible cores available (BSP + APs)
Change-Id: I247d8d1166c77bd01922323b6a0f14ec6640a666
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch makes init_cpus function external so that it can be used
in below scenarios:
1. When coreboot is doing MP initialization as part of
BS_DEV_INIT_CHIPS (exclude this call if user has selected
USE_INTEL_FSP_MP_INIT)
2. coreboot would like to take APs control back after FSP-S has done
with MP initialization based on user select USE_INTEL_FSP_MP_INIT
Also make sure post_cpus_init function is getting executed
unconditionally to update MTRR snapshot on all cores.
Change-Id: Idc03090360f34df074b33ba0fced2d192edf068a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently the DRAM initialization code can only work on 4GB size and
want to support larger memory sizes in future, so add geometry
information to the DRAM calibration parameters.
BUG=none
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: I1fdf50b75c6a552c0a889f21e1a81ab4b9a305fa
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Different density should correspond to different tRFCab and tRFCpb
timing.
BUG=none
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: I2599fcd620cdefe2e12480932ffd75e0416b9545
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Some DRAM control settings need to apply to all channels,
so add those missing settings.
Also fix a typo (0x1 < 0) to (0x1 << 0).
BUG=none
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: I35e25c922ed45216d5f04835abcd10809a8d559a
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add __packed to TYPE17_DMI_INFO structure to remove padding. Remove
reserved fields that are no longer required. Corresponding change will
also be made within fsp to pack the structure.
BUG=b:154046847
TEST=Boot a trembyle with and without the reserved fields and confirm
type 17 table is unchanged.
Cq-Depend: chrome-internal:3194239
Change-Id: I9ba7e2a4fb82c7b0b77ee7c6c075e6211d4f6adf
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This change updates devicetree to enable SSDT generation for world
facing and user facing cameras of jasperlake_rvp. Also removes DSDT
changes related to the world facing camera.
Change-Id: Ib439572bc1d15ef02c86c7bfa88af6b16eb06f97
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Includes changes in mipi_camera driver to fix following issues related
to SSDT generation for IPU devices.
1. acpigen_write_device was not getting called for IPU devices
2. acpigen_pop_len was called for a generic devices without calling
acpigen_write_device
Change-Id: I309edd065719cb8250f1241898bb5854004d2a9f
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44025
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This code is not even being build-tested. Drop it before it grows moss.
Also drop a now-unnecessary #undef directive from one mainboard.
Change-Id: I613e77723d108641f16ec732358849c3bc0e49e0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43220
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This code has been commented out for a long time. Drop it.
Change-Id: Iddc635dc5bbc7a8b42e97f4e2f6d579a839d874b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43264
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch removes all redundant read microcode version implementation
from SoC directory and refer from cpu/intel/microcode/microcode.c file.
TEST=Able to get correct microcode version.
Change-Id: Icb905b18d85f1c5b68fac6905f3c65e95bffa2da
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44175
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Felix Singer