Add rtc MT6359P driver for rtc init and rtc eosc calibration. Refactor
mt8173 and mt8183 code by extracting common API. Move rtc_read and
rtc_write to each SoC folder, because mt8173 and mt8183 access rtc via
pmic wrapper, while mt8192 accesses it via pmif.
Reference datasheet:
Document No: RH-D-2018-0101.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: I57d6738fdec148c7458b2024a0a8225415ca2f3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Memory PLL is used to provide the basic clock for dram controller
and DDRPHY. PLL must be initialized as predefined way.
First, enable PLL POWER and ISO, wait at least 30us, release ISO, then
configure PLL frequency and enable PLL master switch.
At last, enable control ability for SPM to switch between active and
idle when system is switched between normal and low power mode.
TEST=Confirm Memory PLL frequency is right by frequency meter
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ieb4e6cbf19da53d653872b166d3191c7b010dca6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
The mt8183 dsi driver can be shared with mt819x SoC.
Move dsi.c to common/ folder and rename it to dis_v2.c to
differentiate it from mt8173's dsi driver.
TEST=emerge-kukuki coreboot
Change-Id: I722d3e67f230ab8eb729900cdf15b922eb91a072
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add I2C controller for MT8192, and revise the common I2C driver
to support I2C controller running in APDMA async mode. In that
case we have to initiate a different handshake protocol and reset
I2C differently.
BUG=b:155715435
TEST=Asurada boots up to shell
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Change-Id: I13835e00eb674a93aa5496a9870d1e601e263368
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add mtk_init_mcu to load the firmware to the specified memory address
and run the firmware. This function also measures the load time and the
blob size. For example:
mtk_init_mcu: Loaded (and reset) dpm.pm in 15 msecs (14004 bytes)
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ie94001bbda25fe015f43172e92a1006e059de223
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The auxadc (auxiliary analogue-to-digital conversion) is a unit
to identify the plugged peripherals or measure the temperature
or voltages.
The MT8183 auxadc driver can be shared by multiple MediaTek SoCs
so we should move it to the common folder.
Signed-off-by: Po Xu <jg_poxu@mediatek.com>
Change-Id: Id4553e99c3578fa40e28b19a6e010b52650ba41e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
SD Card driver needs to access two regulators - MT6360_LDO5 and
MT6360_LDO3. These two regulators are disabled by default.
Two APIs are implemented:
- mainboard_enable_regulator: Configure the regulator as enabled/disabled.
- mainboard_regulator_is_enabled: Query if the regulator is enabled.
BUG=b:168863056,b:147789962
BRANCH=none
TEST=emerge-asurada coreboot
Change-Id: I391f908fcb33ffdcccc53063644482eabc863ac4
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46687
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, five regulator controls are implemented for DRAM
calibration and DVFS feature.
The regulators for VCORE and VM18 are controlled by MT6359.
The reguatlors for VDD1, VDD2 and VMDDR are controlled by MT6360
via EC.
BUG=b:147789962
BRANCH=none
TEST=verified with DRAM driver
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Id06a8196ca4badc51b06759afb07b5664278d13b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
To enable DVFS, DRAM driver needs to access four different
regulators that SoC can't access directly and need board-specific
implementations.
To support that we need to define the getter and setter APIs for
those regulators.
BUG=b:147789962
BRANCH=none
TEST=verified with DRAM driver
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I0c2d471a7f8628735af90c5b5a5ab3012831e442
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46405
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement mt_fmeter_get_freq_khz() in MT8192 to measure frequency of
some pre-defined clocks by frequency meter.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: I75df0b040ed7ea73d25724a3c80040f4e731118f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45402
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using common mtcmos code to power on audio and display modules in SOC.
TEST=Boots correctly on MT8192EVB. Passes the status check at the end of
mtcmos_power_on()
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: Ie7bff831eecfc2b4d315a577f6ff86befc483eab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45394
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The power status bits of display and audio of MT8192 are different
from the bits of MT8173 & MT8183, so move those under each chip.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: Iaa211b8db733d8aa52d93af9e507042bf0984d55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The UART index is never negative, so make it unsigned and drop the
checks for the index to be non-negative.
Change-Id: I64bd60bd2a3b82552cb3ac6524792b9ac6c09a94
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gpio_common.h needs EINT_BASE from addressmap.h.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I20834e38343410526da0a489fed907acbf479d02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
If panel has too small hfp or hbp, hfp_byte or hbp_byte may become
very small value or negative value. When very small value or
negative value is used, the panel will be scrolling or distorted.
This patch adjusts their values so that they are greater than
the minimum value and keep total of them unchanged.
DSI transfer HBP or HFP, There are some extra packet. ex. packet
header(4byte) and eof(2byte) and (next)hs packet header(4 byte).
the hfp_byte = HFP * BPP - packet header(4byte) and eof(2byte)
and (next)hs packet header(4 byte). So the min hfp_byte is 2 when
HFP = 4.
This is equivalent to the Linux kernel DSI change in:
https://chromium-review.googlesource.com/c/chromiumos/third_party/
kernel/+/2186872
BUG=b:144824303
BRANCH=kukui
TEST=boot damu board with panel CMN N120ACA-EA1 (12" panel and its
hbp only 6), the panel can display without scrolling or
distortions.
Signed-off-by: Paul Ma <magf@bitland.corp-partner.google.com>
Change-Id: I608c01d41ae93c8d5094647bbf3e0ae4a23d814c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41163
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I7c3c75eaf2d7a64e7d833541bcf168b93921a142
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I4c110f60b764c97fab2a29f6f04680196f156da5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
The number of bits per pixel for MIPI_DSI_FMT_RGB666 should be 24
instead of 18.
BRANCH=none
BUG=none
TEST=none
Change-Id: I9574502b2dec4b5a042df3886922ddd8c755da1a
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jitao Shi <jitao.shi@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The extra data transfer in DSI, namely, lpx, hs_prepare, hs_zero,
hs_exit and the sof/eof of DSI packets, will enlarge the line time,
which causes the real frame on dsi bus to be lower than the one
calculated by video timing. Therefore, hfp_byte is reduced by d_phy to
compensate the increase in time by the extra data transfer. However, if
hfp_byte is not large enough, the hsync period will be increased on DSI
data, leading to display scrolling in firmware screen.
To avoid this situation, this patch changes the DSI Tx driver to reduce
both hfp_byte and hbp_byte, with the amount proportional to hfp and hbp,
respectively. Refer to kernel's change in CL:1915442.
Also rename 'phy_timing' to 'timing' to sync with kernel upstream.
Since the phy timing initialization sequence has been corrected, the m
value adjustment in the analogix driver can be removed.
BUG=b:144824303
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
TEST=Boots and sees firmware screen on krane and juniper
TEST=No scrolling issue on juniper AUO and InnoLux panels
Change-Id: I10a4d8a4fb41c309fa1917cf1cdf19dabed98227
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
When configuring MIPI DSI Tx, the value of pcw was calculated from data
rate in MHz, leading to loss of precision. This patch changes to use
data rate in Hz for the calculation so that the resulting value should
be consistent with the one in kernel (CL:1786327).
In addition, change the type of data rate to u32, and calculation of
data rate from pixel clock is changed to use DIV_ROUND_UP for
consistency with kernel (CL:1761843).
Also remove unused variable txdiv.
BRANCH=kukui
BUG=b:149051882
TEST=emerge-jacuzzi coreboot
TEST=No scrolling issue on Juniper AUO and InnoLux panels
Change-Id: I23220d446833b956431006027bbc8cb20fc696a5
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38827
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch changes all existing instances of clrsetbits_leXX() to the
new endian-independent clrsetbitsXX(), after double-checking that
they're all in SoC-specific code operating on CPU registers and not
actually trying to make an endian conversion.
This patch was created by running
sed -i -e 's/\([cs][le][rt]bits\)_le\([136][624]\)/\1\2/g'
across the codebase and cleaning up formatting a bit.
Change-Id: I7fc3e736e5fe927da8960fdcd2aae607b62b5ff4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This adds a common cbmem_top implementation to all coreboot target.
In romstage a static variable will be used to cache the result of
cbmem_top_romstage.
In ramstage if CONFIG_RAMSTAGE_CBMEM_TOP_ARG is set a global variable
needs to be populated by the stage entry with the value passed via the
calling arguments. if CONFIG_RAMSTAGE_CBMEM_TOP_ARG is not set the
same implementation as will be used as in romstage.
Change-Id: Ie767542ee25483acc9a56785ce20a885e9a63098
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
To fix MIPI D-PHY test failure, the hs-prepare should be less than
LimitMin from spec, and we have to enlarge TEOT margin.
BUG=b:138344447
BRANCH=kukui
TEST=Boots correctly on kukui
Change-Id: If91e7a546866299f02432be27fe778be5d7bdc5f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Initialize the input_hertz and uart_pci_addr fields of the lb_serial
struct to prevent later undefined reads in lb_add_serial(). This was
done for exynos5420 in commit ff94e00362 (soc/samsung/exynos5420/uart.c:
Init new serial struct variables), and this patch finishes the rest.
Note that not all of the drivers can have the UART PCI address
configured at build time, so a follow-up patch will be needed to correct
those ones.
Change-Id: I733bc8185e2f2d28a9823495b53d6b09dce4deb1
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1354778
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34548
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some USB 3.0 devices fail to be enumerated after USB reset, and xhci
port status register shows the device is disconnected. After measuring
the USB signal, we found that the USB disconnect threshold was lower and
that the disconnect event was triggered unexpectedly.
USB designers suggest changing discth to 15.
BUG=b:122047652
TEST=emerge-kukui coreboot chromeos-bootimage
Change-Id: I0e8556035b49d693a42cbe1099a6882a1c0ed0d1
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Some boards (e.g., Kukui) need GPIO based CS for SPI0. This patch
changes the pinmux and binds the pins to the correponding SPIs.
When using GPIO based SPI CS, we need to manually make CS log/high
before/after SPI transactions.
BUG=b:132311067
BRANCH=none
TEST=Verified that b/132311067 is irreproducible
Change-Id: I61653fb19242b6ee6be9a45545a8b66e5c9c7cad
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The fixed size of init command in lcm_init_table is wasting lots of
space and we should change to packed array since the command buffer
already provides length information.
With this change, BOE panel init commands have been reduced from 4848
bytes to 1309 bytes.
BUG=b:80501386,b:117254947
TEST=emerge-kukui coreboot chromeos-bootimage; Boots properly
Change-Id: I359dde8e6f2e1c0983f4677193bb47a7ae497ca6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34778
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MT8183 display serial interface (DSI) is based on MIPI
Alliance Specification, supporting high-speed serial data
transfer between host processor and peripheral devices such
as display modules.
DSI supports both video mode and command mode data transfer
defined in MIPI spec, and it also provides bidirectional
transmission with low-power mode to receive messages from
the peripheral.
Reference: MT8183 Application Processor Functional Spec,
6.7 Display Serial Interface (DSI)
BUG=b:80501386,b:117254947
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic413f524ca0b36f0b01f723a71fe9745e2710cd2
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For systems with real MIPI panels (8173/oak was using PS8640 eDP
bridge), we have to send DCS commands to initialize panel.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Ie7c824873465ac82a95bcb0ed67b8b9866987008
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34773
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The video timing should be based on PHY timing. Some values can be
ignored on 8173 because of fixed values in PHY but should be calculated
for newer platforms like 8183.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Id3ad2edc08787414a74188f5050460e98222caf4
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The PHY timing should be calculated by data rate (Mbps). However for
8173 some values were hard-coded so we want to introduce a new
mtk_phy_timing structure and a weak function mtk_dsi_override_phy_timing
that allows per-SOC customization to apply PHY timings.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: I1176ca06dda026029ff431aca7f9e21479eed670
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The only platform-specific difference in mtk_dsi_phy_clk_setting is how
to configure MIPI TX because those registers (and logic) are quite
different across different SOCs.
The calculation of data rate is actually the same so we should isolate
it and move to common, and rename mtk_dsi_phy_clk_setting to a better
name as mtk_dsi_configure_mipi_tx.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: I894dc2c4c053267debf5a58313b2bb489bcf5f3a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The 'bpp' was referred to both 'bits per pixel' and 'bytes per pixel' in
MTK DSI driver and should be corrected. By this change we now always
consider 'bpp' as 'bits per pixel', and rename the variables for other
cases.
BUG=b:80501386,b:117254947
TEST=make -j # board = oak and boots
Change-Id: Ibd405220b73859e5592c68f498af07eef8d7edbc
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34770
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DSI initialization is almost the same for 8173 and 8183, so we want
to move most of common functions into common/dsi.c.
The major board-specific functions left are:
- reset (controller register has different format)
- pin_drv_ctrl (8183 does not need this)
BUG=b:80501386,b:117254947
TEST=make -j # board=oak (mt8173)
Change-Id: I8d4369a3c84db551287a9c9d1b22f552c5f7518d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34769
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
