Change Setup Stage of control messages to have no retries, while data
and status stages may retry until timing out after 1000 retries.
The correct amount of retries might vary by endpoint and device dongle
used, so make it a variable.
Change-Id: I63313f994d0bd3444a3aab527ca942da5de9e6fa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3882
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Transaction consistently completes with 80 to 150 status reads on my
setups. Hardware should always be able to complete this within 125us
as the debug port is serviced at the beginning of each microframe.
Timeout is set to DBGP_MICROFRAME_TIMEOUT_LOOPS=1000 status reads. Do not
retry transactions if this timeout is reached as the host controller
probably needs full re-initialisation to recover.
If this timeout is not reached, but a transaction is corrupted
on the wire, or it is otherwise not properly delivered to the USB device,
transaction is retried upto DBGP_MICROFRAME_RETRIES=10 times.
Change-Id: I44bc0a1bd194cdb5a2c13d5b81fc39bc568ae054
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3881
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Prettier in real-world payloads (ie. FILO)
Change-Id: I9ed968fe527c5d46090e707e2d89b7406a43662e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3887
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These allow to define a kernel image, initrd and command line.
Change-Id: I40155b812728a176b6d15871e1e6c96e4ad693c8
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3893
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
It wasn't even hooked up to the build system anymore.
Change-Id: I4b962ffd945b39451e19da3ec2f7b8e0eecf2e53
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3892
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
In the great tradition of LinuxBIOS this allows adding
a kernel as payload. add-payload is extended to also
allow adding an initial ramdisk (-I filename) and a
command line (-C console=ttyS0).
Change-Id: Iaca499a98b0adf0134e78d6bf020b6531a626aaa
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3302
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for control messages with a write of data stage.
Add status stage after a read of non-zero length data stage.
Do not retry control message if device responds with STALL.
Change-Id: I16fb9ae39630b975af5461b63d050b9adaccef0f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3867
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
USB defines a mechanism to detect certain cases of lost handshakes
using an alternating data sequence number, referred to as data
toggling. This patch fixes each pipe to have its own tracking of
the data toggle state.
Change-Id: I62420bdaeadd0842da3189428a37eeb10c646900
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3865
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Add allocation for endpoint0 as a pipe for control messages.
Endpoint number was already stored in the pipe object, place devnum
there too, although all pipes will use same devnum==127.
Change-Id: I299d139bdd8083af8b04a694e8e41435ec026a25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3864
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Add option to choose one of the EHCI controllers in recent
intel chipsets for usbdebug use.
Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in
rcba_config() for some mainboards, check the PCI class code
for match.
Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3440
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Two new nvram variables control disabling the two non-ME NICs
on the mainboard. This is implemented by disabling their PCIe bridge.
Change-Id: I086f0d79de3ad0b53fa0ec40648d63378070e3bd
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3870
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Collect early timestamps in Lenovo X60’s romstage.
Selecting the option `COLLECT_TIMESTAMPS` in Kconfig and then
doing `cbmem --timestamps` should output the timestamps.
Change-Id: I7bd30f03a1b85c38e89c19cdf88b2d20b24abed8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3587
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The northbridge defines it already and to the same value.
Change-Id: Ia5d856258fac52ea0b249142f70a89123ca04f82
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3876
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
acpica-unix-20130626 doesn't use bin32 and bin64 to save the objects
any more.
Change-Id: I419ecc987e2adcd860a8ad1bf2f6b5c4dd40fd8a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/3885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested on Ubuntu 12.10. S3 is supported. No HD Audio.
Mainboard details: http://www.asrock.com/ipc/overview.asp?Model=IMB-A180
Change-Id: I75254194ab5da8e5c61383d8f85aa4e300815637
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3880
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
src/southbridge/amd/agesa/hudson/Kconfig config default value,
mainboard Kconfig config value for specific mainboard.
bit 1,0 - pin 0
bit 3,2 - pin 1
bit 5,4 - pin 2
bit 7,6 - pin 3
Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3879
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
flashrom has started to use revision IDs to distinguish AMD chipsets
and fails (even more) to build with libpayload since then because
PCI_REVISION_ID is undefined in libpayload's pci header.
Change-Id: If7440a48c1005a4ba4fc09303f47cdfa9f408ad1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3884
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Add a function to test if pci_devfn_t matches with a device
instance of struct device, by comparing bus:dev.fn.
Change-Id: Ic6c3148ac62c7183246d83302ee504b17064c794
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3474
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PNP access
functions for ramstage using the inlined functions from romstage.
Change-Id: I2a0bd8194acaf9c4c7252a29376eec363397e3a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3871
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PCI access
functions for ramstage using the inlined functions from romstage.
Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
After an USB device sees USB bus reset on the bus, it will reset to
device number 0. Per the EHCI debug port specification, a debug
dongle device may reset to the fixed debug device number of 127 instead.
Thus there is no need to try device numbers from 1 to 126.
Do a sanity-check on a returned debug descriptor as I experienced
some USB flash memory to respond on this request with zero-fill data.
Change-Id: I78d58f3dc049cd8c20c6e2aa3a4207ad7e6a6d33
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3861
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Resetting an EHCI controller when it is not halted can have
undefined behaviour. This mostly fixes a case where calling
usbdebug_init() twice would fail to reset the USB dongle device
properly.
On amd/persimmon it still requires one extra retry, but at least it
is now possible to have usbdebug enabled for both romstage and
ramstage.
Change-Id: Ib0e6e5a0167404f68af2edf112306fdb8def0be9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3862
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Ported from spi/winbond.c.
Fixes this error:
ICH SPI: Too much to write.
Does your SPI chip driver use CONTROLLER_PAGE_LIMIT?
Change-Id: I50db8fd1104d3b7d319b278b14f97e3ff9cb6404
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3877
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This quirk is needed with a DIY debug dongle using obsolete
CY7C68013 (aka FX2) USB chips. Old revision of chip requires a
SET_CONFIGURATION to be sent, while this is not required in EHCI
debug port specs.
Change-Id: I4926eb19b7e991d6efeef782682756571ad006b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
When we create low-level debugging of EHCI controller registers,
we call printk() within printk(). In ramstage this would leave us
with deadlock waiting on the console spinlock.
Change-Id: Idbe029af9af76de27094bb2964c60d9ccfdd96e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3860
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If ramstage is not compressed, the CBFS module in romstage doesn't
need to support LZMA. Removing the LZMA module in this case can save
about 3000 bytes in romstage.
Change-Id: Id6f7869e32979080e2985c07029edcb39eee9106
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3878
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The AMD AGESA function to move the stack from cache-as-ram to
actual RAM doesn't need any help. The current implementation has
an INVD instruction just before cache-as-RAM is torn down. It isn't
needed for Trinity processors and makes Kabini boot unreliable.
Change-Id: Ibe9e4105eee032471ccbb2d537471d5fa5847d22
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3852
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
It still pointed to the old binary despite implementing the newer interface
Change-Id: Iebd5dae98168f5568f3ad6a18c5ebde9abc3ece0
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3869
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Drop unused and commented out variable, and fix a comment while at it.
Change-Id: I1bd7d10aca949c8579433ea1c91264fd816a3fb4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3873
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
SEABIOS_PS2_TIMEOUT needs a default, otherwise the "allyesconfig" target
hangs in an endless loop.
The given default is correctly overridden by the (currently sole) user,
the lenovo/x60 target.
Change-Id: I3f5e347c29ccbb4d711a489d067b6c909f030bd0
Reported-by: Kyösti Mälkki
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3874
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Add Kconfig option SQUELCH_EARLY_SMP and have it enabled by
default.
Console drivers have unpredictable results if multiple threads
attempt to share same resources without spinlock. Serial UARTs
have not had huge problems, only distorted output, but those
relying on cache-as-ram (CBMEM and usbdebug) may require this.
Change-Id: I7f406fdea7b6dc6a341c4da2fab56f7b7ff568b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3854
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Move the floppy drive enumeration from _INI() and PROB(),
which stored the enumeration results into _FDE into _FDE().
_INI is called by any ACPI-capable OS on boot while _FDE
is rarely used. So it's better to run the enumeration when
requested rather than unconditionally.
Change-Id: Icf1e2a551806592faa8ba8d80fa8d02681602007
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The parallel port of the W83627HF can be configured on any port
between 0x100 and 0xFFC with 4 byte alignment for traditional modes
and 8 byte alignment for EPP mode. As the ACPI specification says
that the maximum acceptable starting address has to be a multiple
of the alignment granularity, correct the maximum starting address
from 0xFFC to 0xFF8.
Change-Id: I272e09d091149791f2867b1d06e4fc27bc1bb2cd
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/2942
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows mainboards to preconfigure a ps2-keyboard-spinup
timeout when SeaBIOS is chosen as the payload.
The Kconfig option can be changed manually if CONFIG_EXPERT is set.
Change-Id: I5732b18ef04f4bdef6236f35039656ad02011aec
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3734
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This simplifies storing SeaBIOS parameters in CBFS.
Change-Id: I301644ba0d7a9cb5917c37a3b4ceddfa59e34e77
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3733
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The slightly hackish ioapic ressource reservation is needed for i440fx
emulation only, for q35 the ich9 southbridge driver handles this just
fine.
[ Side note: The i440fx chipset emulated by qemu is pimped up with alot
of stuff which never existed on real hardware, which leads
to tweaks like this one. ]
Change-Id: I06bf54cbc247ccf17aa9063fb7dee9def323c605
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3850
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The board name in that variable name is not necessary, as it is not board
dependent, that means using the file as a template for making a new
coreboot port for another motherboard the variable does not need to be
changed, and just increases the code differences between AMD Parmer,
AMD Thather and ASUS F2A85-M. So use a generic name.
The same was done for AMD Persimmon (and inherited by the LiPPERT
FrontRunner/Toucan-AF) in the following commit.
commit 5e70766f14
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Tue Feb 26 15:56:11 2013 +0100
AMD Fam14 boards: reduce unnecessary differences, 2nd attempt
Reviewed-on: http://review.coreboot.org/2529
The board name is *not* removed from the `CODEC_ENTRY` variable name as
the verb table not only depends on the codec but also on the board [1].
Having the board name in the variable name is a good indicator that the
pin configuration needs to be adapted when taking this file as a template
for a new port. If it was board independent, a default chip configuration
could be used and shared between all boards, which is unfortunately not
the case.
[1] Unfortunately I was not able to find Jens’ comment in my mail archive
and in the Gerrit Web interface. Not sure where it is, but I am sure
he made that comment.
Change-Id: I440a306cf4ff0a5b1b61d1983d70c66d129904d0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3199
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
As Nico noticed for the W83627DHG, the power management bits to power down
individual logical devices on Winbond superios are named counterintuitively
and need to be set when the logical device should be powered.
This corrects the power management methods for the W83627HF.
Change-Id: I98bccd550a0513c62bfa9480275f88c566691bc8
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3605
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Kyösti Mälkki