Traditionally, we have always allocated 1 DRAM ID per part number.
However, on nami, we have run out of DRAM IDs because we have
supported so many different parts. We are now adopting the use of
generic SPD files that are feature-based rather than specific to each
part, allowing us to support multiple parts with a single SPD.
The common SPDs were created by taking current SPDs in Nami (which is
using the same DDR4 parts as Hatch) and zeroing out all the
manufacturer information and part names. Additionally, we zeroed out
bytes 128 (raw card extension, module nominal height), 129 (module
maximum thickness), and 130 (reference raw card used) after verifying
that they are not used in FSP. We verified with these fields zeroed
out, all nami devices could boot up without errors. We also verified
on the two Hatch skus that we have (4G 2400, 8G 2666) that the generic
SPDs boot properly.
BUG=b:122959294
BRANCH=None
TEST=Make sure that we can boot up on both 4G Samsung and 8G Hynix DDR4
devices that we currently have.
Change-Id: I14d9e6b13975b6a65b506e6cd475160711b8f6d4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
"is_wakeup_source" flag is used to indicate if the concerned device can
trigger a wakeup. This flag is redundant with the "wake" GPE event
definition. So remove the redundant flag and use the "wake" GPE event to
mark the wakeup source.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS. Ensure that the device is marked as wakeup-source
in SSDT if wake GPE is configured. Ensure that the system can suspend
and the device acts as a wakeup source
Change-Id: I99237323639df1cb72e3a81bcfed869900a2eefa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current coreboot size is not adequate for adding new features.
Note for cros: This change is for merge to ToT only and should not be
cherry-picked into reef's firmware branch.
BUG=chromium:903833
TEST=emerge-reef coreboot
Change-Id: Ie7a25c4638c474e81fb34b57de0dfc1bf393ea67
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reconfigures the GPP_D1 GPIO pin as a no-connect. It really
doesn't go anywhere today or on previous revs of the board.
BUG=b:110614620
BRANCH=none
TEST=atlas still boots
Change-Id: Iea53cf909f8f060c4e0f14e8b4ad579b838b7caa
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit 7696290004.
We're seeing trackpad problems on some units with the I2C bus running
at 1MHz but not at 400KHz. So, revert back to 400KHz until we
understand how to make 1MHz operation more robust.
BUG=b:123650686
Change-Id: Ifb06afece9eee0c153240d35e6c3001f5b74f310
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The default value for Chrome OS HWID should be different.
Calculated as HWID v1.
BUG=b:123336677
BRANCH=kukui
TEST=build and boots properly.
Change-Id: I39c640562c1c3b117292b8abacd36a4a9c2fa6c6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This change enables exporting the reset GPIO for CNVi Bluetooth module to
the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset
gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured
that the kernel btusb driver is able to find the exported GPIO in the
devices with CNVi BT module.
Change-Id: I10f28bfe705da5104d709ae2ed91a8ae003fa639
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This implementation adds support to create ACPI package for USB port
capability (_UPC) and physical location of device (_PLD) for USB2 port 10.
BUG🅱️123375275
TEST:Verify _UPC and _PLD ACPI packages gets published for USB2 Port 10
in SSDT and BT is functional in discrete and integrated mode.
Change-Id: Ifeab24505a700e8e4677be20074c7d0400769cec
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31197
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable USB ACPI driver for octopus boards and add bluetooth USB ACPI
configuration in devicetree. This change enables exporting the bluetooth
reset GPIO to the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS
Change-Id: Ie40f1ad70f21a6fd398ce23d060e0c588ba6ce41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In payloads, we didn't set GPIO modes. We have to set up GPIO mode in
coreboot for payloads.
BUG=b:80501386
BRANCH=none
TEST=HW reboot works in depthcharge
Change-Id: Ibd2c6c071871edc59497fbb245cdbec6a814f621
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31148
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Real unused GPIO pad is GPIO_123, but GPIO_122 is configured as unused pad.
This patch corrects the configuration.
BUG=NONE
BRANCH=octopus
TEST=emerge-octopus coreboot
Change-Id: I4473bd66a4162f5aee3b998aacba906824728fc8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake
the AP from suspend. Also create a task to initialize the hostevent
wake mask properly.
BUG=b:123325238,b:123325720
BRANCH=None
TEST=from AP console: powerd_dbus_suspend
from EC console: hostevent (make sure wake mask set)
from EC console: gpioset PCH_WAKE_L 0
Make sure device wakes up
Also, checked to make sure keyboard press wakes up
device from S3.
Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
List Raydium touchscreen in the devicetree so that the correct ACPI device
are created.
BUG=b:121105424
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
reflash the coreboot to DUT, make sure the Raydium touchscreen can work.
Change-Id: I9ffb2a858f31a8b003086806de07f4079870cddf
Signed-off-by: Hao He <hao.he@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31116
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL moves some initialization steps from bootblock to verstage. This
will save us about 2700 bytes (before compression) / 1024 bytes (after
LZ4 compression) in bootblock. In case of CONFIG_VBOOT is disabled,
these initialization steps will be done in romstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I9968d88c54283ef334d1ab975086d4adb3363bd6
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Asserting GPIO PERIPHERAL_EN8 will send a signal to EC to trigger a HW
reset for SoC and H1.
BUG=b:80501386
BRANCH=none
TEST=emerge-kukui coreboot; manually verified the do_board_reset() on
Kukui P1
Change-Id: I9afad84af2031a766bc08fc76c8b5f55588c453a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31118
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Separate WDT reset function from WDT driver, then we can use the common
WDT driver and have a board-specific reset function on different boards.
In Kukui, we plan to use GPIO HW reset, instead of WDT reset. Add config
"MISSING_BOARD_RESET" in Kukui to pass the build for now.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot;
Change-Id: Ica07fe3a027cd7e9eb6d10202c3ef3ed7bea00c2
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31121
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ELAN touchpad supports up to 400KHz, so we need to limit its CLK
frequency to 400HKz.
BUG=b:123376618
BRANCH=octopus
TEST=built and verified touchpad I2C clk frequency gets be lower than 400KHz
Change-Id: If7a43fe20c7e5abdf23c8c36e34c072c371563bf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
New emmc DLL values for Ampton
BUG=b:122307153
TEST=Boot to OS on 5 systems
Change-Id: Iadd58d254f4bb384f483c2c3e5615f7569d5211c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add support Synaptics touch pad for Aleena/Kasumi.
BUG=b:122549449
BRANCH=master
TEST= Check if synaptics touch pad working in ChromeOS.
Change-Id: Icab1b312f1943b27037ef458044ce9e7172919ee
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31064
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable gpio_keys driver for bobba and add required configuration in the
device tree to handle the pen eject event.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder.
Change-Id: I768b89d2b45f4dcab6d235b11ce00544a827f22d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL adds a new function mt8183_early_init, which includes all
initializations that should be done in early stages. All mainboards
using MT8183 should manually call it in either bootblock or verstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I35d7ab875395da913b967ae1f7b72359be3e744a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch enables relevant GPIOs to enable WWAN. WWAN also requires to
enable USB 2 port 6 and USB3 port 5 which is already enabled in device
tree related changes.
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I1559bbc6168aec1a369bf3291d2c1e2f9a2fbe07
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable PCIe WLAN for hatch
1. Enable PCI port 14 for PCIe WLAN
2. Enable CLKREQ, CLK SRC 3 for PCI port 14
3. GPIO pad config for WLAN and BT
USB port for BT has already been enabled so not included in this patch
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I4f2a6eb37a467ad8b8cdde8fe6b657fabb383b04
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
With the memory controller the separate sockets becomes a useless
distinction. They all used the same code anyway.
UNTESTED: This also updates autoport.
Change-Id: I044d434a5b8fca75db9eb193c7ffc60f3c78212b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31031
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Kukui with vboot enabled will build with `detachable_ui`, which needs
larger space in CBFS for more complicated assets. So we need to revise
FMAP sections:
- BOOTBLOCK (not really used) only needs <= 32K.
- GBB can be much smaller since assets moved from GBB to CBFS.
- FMAP is re-ordered (with the cost of less efficient in bsearch) so CBFS can
get larger continuous space.
- COREBOOT(CBFS) should take all space left.
Since FMAP and COREBOOT have changed location, the system will need to
reflash EC (which contains the new bootblock) as well.
BUG=b:123202015
TEST=Builds and boots on Kukui P1
Change-Id: I22cff99dca8c396c5897c3f6631721af40f3ffbd
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
disable unused usb2 ports of bard and ekko skus
BUG=120874946
TEST=build a test firmware and run lsusb to check usb ports
Change-Id: I2ef3cd17ada8b65c96bc80675650905949f235e1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30986
Reviewed-by: Vincent Wang <vwang@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
close the FP module power in power off (s5)
BUG=122887366
BRANCH=Nami
TEST= build test firmware and measure the fp power enable pin
Change-Id: I80ddfbf1edf7c6435d263d5f5e0edb8b8701817d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30910
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
