This patch ensures soc_finalize() is getting called at the entry of
BS_PAYLOAD_BOOT boot state instead of BS_PAYLOAD_LOAD, BS_ON_EXIT.
The purpose of this change is to accommodate more time to push out
sending CSE EOP messages at post.
BUG=b:200644229
TEST=coreboot serial log suggests soc_finalize() is getting called
as part of the BS_PAYLOAD_BOOT entry.
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
BS: BS_PAYLOAD_BOOT entry times (exec / console): 21 / 15 ms
Change-Id: I8632eca057255d7f4a38b64fd17c1f3d84123051
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Prior to coreboot sending EOP messages during post, it's important to
ensure that CSE is not in Idle state. In case CSE is in Dev Idle
state (which means D0I3 bit is set), reset this bit before sending
EOP command.
This patch ensures coreboot has provision to send CSE EOP messages even
after the FSP Notify phase without any delays waiting for the device
to respond or timeout.
BUG=b:200644229
TEST=Able to send CSE EOP message even after FSP Notify phase.
Attempting CSE EOP msg sending post FSP notify without this code change
causes `timeout` issue as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 171 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
HECI: timed out reading answer!
HECI: Failed to receive!
HECI: receive Failed
HECI: EOP send/receive fail
ERROR: Failed to send EOP to CSE, 2
cse: CSE status registers: HFSTS1: 0x90000255, HFSTS2: 0xf10516 HFSTS3:
0x20
VB2:vb2api_fail() Need recovery, reason: 0x31 / 0xc
Saving nvdata
board_reset() called!
full_reset() called!
Attempting CSE EOP msg sending post FSP notify with this code change
is `successful` as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 170 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
CSE: EOP requested action: continue boot
CSE EOP successful, continuing boot
Change-Id: Iae1bc52e94b08f97004424ea0c147d6da8aca6e2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures APIs that are responsible for CSE device state
transition between active to idle and vice-versa are available
publically for other modules/boot stages to consume.
BUG=b:200644229
TEST=Able to build and boot ADLRVP-P.
Change-Id: Ia480877822d343f2b4c9bf87b246812186d49ea3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update to recommended Rcomp drive strength value for DDR4 as per
MRC team's input.
Additionally, add space around the `targets` array.
Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507d99a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
M.2 spec describes PERST# should be sequenced after power enable.
BUG=b:201512872
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ie164ddb29f947e190fa87b31165e3c84b07926e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58034
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These platforms no longer use reg-script. Drop unneeded select.
Change-Id: I8fc4dc29d25dffbf9ed1947d0ff013b2fae0faaf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: I87d1278360a231cbe5b5f825ad9a448e59e63ea2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: Ib3c83131c30fd02c579b910cfad6843eb28ba8f1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The current names of the PMC init/enable callbacks are very confusing.
Rename them.
Change-Id: I69f54f3b4e1ea9a9b4fa5c8dd9c0d454d7cd1283
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In CB:52662 when MIPI display support was added, we accidentally changed
the code flow for eDP displays such that i2c_init() will no longer be
called when display_init_required() is false. This is a problem because
on this platform, i2c_init() does not just prepare the I2C controller
for firmware use, it also loads firmware to the controller that makes it
behave like an I2C device in the first place -- a step that the kernel
cannot later do on its own if the firmware didn't already do it.
Skipping this initialization means the I2C controller becomes unusable
to the kernel.
This patch fixes the issue by making the i2c_init() unconditional again.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4546c31d87d91113eeef7dc7a18599a87e6d6eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58026
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rename the `ecps` GNVS struct member to `epcs` to match the name in ASL.
Change-Id: I1f6b97309eea75e7dbb4e5e664660df05ec0845e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Initializing SAR sensor (QUP2, address 0x988000)
BUG=b:198456205
BRANCH=None
TEST=Boot into kernel and make sure no i2c errors for 0x988000 in
dmesg
Change-Id: I75b0e9173d4c49b5e7308158a678964d6637b225
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For Herobrine variants that include a finger print sensor, we will
need to power sequence it. We are using the same FP sensor as
trogdor, so we will follow the timings used for trogdor from
CL:2695676.
BUG=b:198474942
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B
Change-Id: Ica6eafc47cf1b95eeb8d94c6e0a8c88519665e3f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58021
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ID "10029836" for machine driver, "RTL5682" for ALC5682I and "MX98357A" for MAX98360.
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: Iab9d11adb7cd08effa2a9b6a627832bd89cb3cb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Updating from commit id c5a482ed:
2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven)
to commit id 13f601f:
13f601f vboot: boot from miniOS recovery kernels on disk b
This brings in 14 new commits.
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: I66788ea434a6000435b97ce64107f3b5da882414
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57994
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Iba91b51cbbe7adc502372c9a026867de61d8035d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The %fs and %gs segment are typically used to implement thread local
storage or cpu local storage. We don't currently use these in coreboot,
so there is no reason to map them. By setting the segment index to 0,
it disables the segment. If an instruction tries to read from one of
these segments an exception will be raised.
The end goal is to make cpu_info() use the %gs segment. This will remove
the stack alignment requirements and fix smm_do_relocation.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaa376e562acc6bd1dfffb7a23bdec82aa474c1d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This CL adds support for new ADL-M graphics Device ID 0x46c3.
TEST=boot to OS
Change-Id: Ib55fb501f96fe9bcc328202511bbfe84a3122285
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add ADLP 242 sku power related settings, which follow the settings of
ADLP 282 sku (both are 15w).
BUG=b:201253904
TEST=Build and check fsp log to confirm the settings are set properly.
Change-Id: I829dd690c22d167a507b1910106da06b275cec09
Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The voltage rail discharge times have been measured, so therefore
the boot time on a cold boot when the CSE must go through a global reset
and thus a trip to S5 can be optimized. Select the lowest applicable
value for each PchPmSlp UPD that can be used with these measurements.
This is programmed in the baseboard because the measured discharge times
leave (what should be) plenty of margin for variants to also not violate
any power sequencing guidelines from the PDG.
BUG=b:184799383
TEST=verified time in S5 during a global reset is ~1s instead of 4s
Change-Id: Ia373c47b3967d68ddac21707c6eb4565d9d6519e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
The UPDs for PM power cycle duration and SLP_* signal durations are all
identical to Tiger Lake, so add similar support, but use enums instead
of comments to represent the durations symbolically.
BUG=b:184799383
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a531f042658894bcbc6a76eff453c06e90d66b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57891
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These methods are never used in the code. Drop them.
Change-Id: If5568b494f821d2647ada5ae845bcd015708520e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
These fields are never used in the code. Drop them.
Change-Id: Icd07f2d704c19126bf6df4d740c21d5a1342061b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This field is never used in the code. Drop it.
Change-Id: I88207ec369ab83823ef2f3fc40f68a0980ce9663
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
BUG=b:192429713
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507c99b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57980
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove unused drivers and some fast calibration implementations
to align with the latest MTK memory reference code.
TEST=boot to kernel
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I2e6be2e16c139e48c65352fe2eabf16bf9cd550a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57978
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: I2c4fb1933eda2eb75bfe9181f13e189ec66cadf9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that taeko can successfully
boot into OS with non-serial coreboot.
BUG=b:199969366 & b:200711149
TEST=Build FW and test with non-serial FW reboot 20 times pass.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I032c5b90fb2148c4075d6ead3e4161c0cc659b20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add wifi sar for magma.
Due to fw-config cannot distinguish between magolor and magma.
Using sku_id to decide to load magma custom wifi sar.
BUG=b:192423859
TEST= emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Iac15e958e61be6e3c136fb9be18b4695823ad1c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Currently, static analyzers don't recognize that hlt() doesn't return,
so they show errors like uninitialized variables assuming that it does
return. This takes care of that problem.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia2325700b10fe1f89d749edfe5aee72b47d02f2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Update PL1 min and max values to 6 W for Galith/Gallop systems.
BUG=b:201010771
BRANCH=None
TEST=Build and verify on Galith/Gallop system
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I0dfda3c2c830a2ce203668431f396859e782aa3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The headers added are generated as per FSP v2374_01.
Previous FSP version was v2347_00.
Changes Include:
- Offset change in FspmUpd.h and FspsUpd.h
BUG=b:201239436
BRANCH=None
TEST=Build and boot brya
Cq-Depend: chrome-internal:4150766
Change-Id: I097e854bcb4033bdaf2498fb97b255e87d3dd70f
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57920
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the next build phase, modify the HID of the speaker amp to
MX98360A.
BUG=b:199098681
BRANCH=none
TEST=build coreboot without error
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I0c318464fca7d35bbffd7ea0f5694b83acedff0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The current MRC binaries for Bay Trail are always ELF files. Always
adjust the position in CBFS using the ELF header regardless of file
names. Without adjusting the position, the system hangs right after
calling into MRC.
TEST: MRC position in CBFS does not change for bostentech/gbyt4.
Change-Id: I74e1246a5fac3f3649be9842ff13c2fc70f72a20
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57989
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor DPTF section of code under the kracko overridetree. This makes kracko override dptf section of dedede/baseboard, because the DPTF tool's CRT, PSV and TSR3 settings are different than expected.
BUG=b:187482019
BRANCH=dedede
TEST=Built and tested on dedede system
Change-Id: Iacc543f961a7f4652ee8583920b1794f916c7ec9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This file does not exist in the coreboot tree. One should place this
file in the `site-local` subdirectory and specify the paths by means
of `site-local/Kconfig`.
Change-Id: I86ac2a6176947f12194bec6b63bedd7db79820a0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This code is identical except for some renaming.
Change-Id: I93795a6087ce0daca27c0d5038a1febd6ca9c775
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This will help reduce duplication and make it easier to add new members
to the cpu_info struct.
BUG=b:194391185, b:179699789
TEST=Compare assembly of romstage and ramstage before and after
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I31f264f4bb8b605fa3cb3bfff0d9bf79224072aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
mb_set_up_early_espi should only be called when
SOC_AMD_COMMON_BLOCK_USE_ESPI is selected.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic8ad724a2a79c1995fbe9d97f11a0f69eed9435c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Enable CCP DMA use in PSP verstage. This helps to reduce the boot time.
BUG=b:194990811
TEST=Build and boot to OS in Guybrush. Observed a 35 - 40 ms improvement
in the boot time.
Before CCP DMA:
508:finished loading body 898,286 (287,576)
Total Time: 2,146,182
After CCP DMA:
508:finished loading body 853,627 (240,061)
Total Time: 2,110,117
Cq-Depend: chrome-internal:4116566
Change-Id: I6e4f081622a2ec78763adf56548204efc1bccf39
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
PSP verstage can access the boot device either in Programmed I/O mode or
DMA mode. Introduce a boot device driver and use the appropriate mode
based on the SoC support.
BUG=b:194990811
TEST=Build and boot to OS in Guybrush.
Change-Id: I8ca5290156199548916852e48f4e11de7cb886fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57563
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Subrata Banik