GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs that are being set low had the wrong value getting set.
FCH_GPIO_OUTPUT_VALUE was being set instead of FCH_GPIO_OUTPUT_ENABLE.
BUG=b:70234300
TEST=Build and boot Grunt
Change-Id: I16792b76252506a43aac92738b04096ae3fde01c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Grunt and Kahlee touchpads are on different i2c busses; I2CC and I2CD,
respectively.
Since grunt is the 'baseboard', put its configuration under baseboard, and
include it from the grunt variant.
BUG=b:71820409
TEST=Boot grunt to kernel, use evtest to test trackpad.
TEST=Boot kahlee to kernel, use evtest to test trackpad.
Change-Id: I1aeacf9a840342e73c1e219a825b39a124b4dd57
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23232
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Grunt and Kahlee have different audio codecs.
Create a new audio .asl for the baseboard for grunt's codec, link
to it from the grunt mainboard, and move the kahlee codec table
from the baseboard mainboard to its own .asl in variant/kahlee.
Note, we can't use the generic drivers due to the PCI scope
expectation. The AMD I2C are not PCI devices.
BUG=b:69397774
TEST=Codec driver loads. Check dmesg.
Change-Id: I1cc245357d1f3d444e5a5012466eaa5d75d637eb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23226
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the apci/ to the baseboard and move mainboard.asl to
each variant.
BUG=b:71873651
TEST=build
BRANCH=none
Change-Id: I8a829f2946e4b280cd78574eb8dbda6c2a9a1028
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The ACPI unique identifier (_UID) should be unique.
This doesn't actually matter much for Linux, though, since the kernel
can handle it when the BIOS doesn't get this right.
See:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b4b6cae2f36d92b31788f10816709d5290a1119a
b4b6cae2f36d ACPI / platform: use ACPI device name instead of _HID._UID
Change-Id: I8b1b3143174584a93f3d45bf482b8922b3f0ec12
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
This reverts commit 0f5651584ebb8e2ccfa151275bfd2f70e74bae9b.
This is not the correct fix for the heap allocator.
It looks like the root cause is in the buffer size of the
deallocate function.
Change-Id: I33c479a30d89a665677d3e4914194ae8136504af
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23245
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Meowth uses GPD_2 as a dedicated lan_wake pin, so GPD_2 must
be set to use NF1 instead of gpio.
BUG=b:64395641
BRANCH=none
TEST=none
Change-Id: Iadf7158a792dfae0ea5e824d197a558524cdb5fd
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Intense PC uses FCBGA1023 socket, not rPGA989. Correct the socket
in the devicetree.
Change-Id: Ie657af2f51dfb7add90b19b26c0c37d312d59821
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Enable the UART via SMSC SIO1007 SuperIO, this allows you to see boot
boot messages from coreboot over the integrated RS-232 port (requires
use of included dongle).
Change-Id: I11a4c532ed73a0cf27d6e7bef6e04035c3942567
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The code is based on autoport and that for 8470p.
Tested:
- CPU i5-3437U
- Slotted DIMM 8GiB
- Soldered RAM 4GiB from Hynix (There may be more models here)
- Onboard USB2 interfaces (digitizer, wlan slot, wwan slot, camera)
- Mini pci-e on wlan slot
- On board SDHCI connected to pci-e
- USB3 ports
- USB3 hub on dock (connected to USB3 port 1)
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.13.13-1 within Debian GNU/Linux testing, loaded from
SeaBIOS, or Linux payload (Heads)
Not work:
- An "NFC" device connected to LPC
Not implemented yet:
- Detecting the model of Soldered RAM at runtime, and loading
the corresponding SPD datum (3 observed) from CBFS
Change-Id: Iba9c361591697e6a2b3b7b485f7f1649c2a83524
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/22972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
We check for NULL from the return of function acpi_device_path
before passing it to acpigen_write_scope to avoid NULL pointer
dereference.
Change-Id: I997461c9b639acc3c323263d304333d3a894267c
Found-by: Klockworks
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/23094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to Intel document #559100 KBL EDS v2.8, section 7.2
DC specifications, the IccMax setting for KBL-U, KBL-U42 and
Celeron/Pentium are different. This patch overrides the IccMax
settings for KBL-U/R/Y since device tree could not handle all
KBL-U/R combinations when multiple SKUs are adopted in a project.
Besides, it is inefficient to maintain the same code for all
variants. Hence, place it in the common code so that all variants
could leverage the benefits.
+----------------+-------------+---------------+------+-----+
| Domain/Setting | SA | IA | GTUS | GTS |
+----------------+-------------+---------------+------+-----+
| IccMax(KBL-U/R)| 6A(U42) | 64A(U42) | 31A | 31A |
| | 4.5A(Others)| 29A(Celeron) | | |
| | | 32A(i3/i5) | | |
+----------------+-------------+---------------+------+-----+
| IccMax(KBL-Y) | 4.1A | 24A | 24A | 24A |
+----------------+-------------+---------------+------+-----+
BUG=b:71369428
BRANCH=None
TEST=Remove icc_max setting from devicetree & emerge-fizz coreboot
chromeos-bootimage & Ensure the KBL-U42, KBL-U22 and Celeron
SKUs are identified correctly and IccMax settings are passed
to FSPS correctly.
Change-Id: I291462b73d3fbd17f17975de7fd77dc48ca99251
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The EC does enable bluetooth on wifi cards and BDC at the same time.
Check the new Kconfig to support bluetooth on wifi in case no BDC
is installed and the BDC detection fails.
Change-Id: I23f14c937252a296dc543db49ec9e093e7e24604
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fizz has external Lan on PCIE port.
The Lan device on PCH is not used.
BUG=b:70889517
Change-Id: I99894bedec14a44724ac7c22d0c894132a795b78
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds the EC_GOOGLE_CHROMEEC_SWITCHES option so that we
use the common switch.c file
Change-Id: I93a2ba63015db17989c89ce1b5897de6a93e201f
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/23131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds recovery cache.
TEST:glkrvp boots with this change and also FAFT test
firmware_CorruptRecoveryCache passes.
Change-Id: I9b32628d814693fb0591fc3750348d48cf9e26f1
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/23067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Digitizer power is not controlled by SoC. Also, since the digitizer
uses I2C-HID driver in Linux kernel, the device is put into sleep
anytime system is suspended. Thus, there is no need to control the
reset gpio using ACPI power resource.
TEST=Verified that digitizer device is properly detected on boot-up
and after suspend/resume.
Change-Id: Id11b8412d0ac48b2701d53b0a22ad3b747b544ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of duplicating code in each mainboard that supports HDA use
the common driver and provide the HDA verb table.
This was compile tested for both variants with "abuild -t intel/kblrvp"
Change-Id: Ie3bab7aabcfa040935062b7764853df8fb19b04d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There is common HDA code in soc/intel/common that provides generic
HDA support functions, but it does not provide a driver.
This change adds a common block driver for HDA that provides a
ramstage driver for SOCs that need to initialize an HDA codec.
This was tested on a board with an HDA codec to ensure that it
properly detected it and ran the codec init steps.
Change-Id: I41b4c54d3c81e1f09810cfaf934ffacafca1cf38
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
A side effect of using the common MTRR assignment code is the flash
device loses its WP setting and is no longer cacheable. After MTRR
setup, reenable the setting for the duration of POST.
TEST=Run on Kahlee and inspect MTRRs prior to AmdInitLate()
BUG=b:70536683
Change-Id: Ib4924e96e2876e1e92121bb52d1931ead723d730
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The heap allocator would try to split a buffer node that
was too small for another node. In the failing case, the buffer
node was 0x140 bytes and the requested size was 0x133 bytes.
The logic would check that there was room for the header and
buffer and try to split the buffer node. The buffer node header
is 0xC bytes, so 0x13F bytes are need. The problem is that it didn't
leave room for another node header and a little space for a buffer.
BUG=b:71764350
TEST= Boot grunt.
BRANCH=none
Change-Id: Iece5e12d5787415a335bb953985331a5dc312152
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
The Port initializer had been changed from PortDisabled to PortEnabled,
but engine inializer hadn't been updated from PcieUnusedEngine to
PciePortEngine. Update this so the port works.
Also change disabled port to PcieUnusedEngine.
BUG=b:71818026
TEST=PCIe device now shows up on D2F4
Change-Id: I11eb8c1fbad12fa9cf34d758a4ef3c22ef8ba4f7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23210
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After running `lint-stable` in the pre-commit hook, its result is
ignored. This behavior was introduced in commit b18f522b
(lint/gitconfig: Enable checkpatch.pl checking of commits) and it
doesn't seem intentional. This issue was also mentioned in the revert
discussion (https://review.coreboot.org/c/coreboot/+/17440).
Enable `errexit` mode of the shell so that the hook fails when an error
occurs in any of the tests. Also, enable `nounset` mode to catch typos
easier.
Change-Id: I749963167660ea6a1a04d40a14ad1113e82f0f86
Signed-off-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/23130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
If using type-C charger, then PsysPl2 may be lower than barrel jack
value of 90W, so need to override value to the max power of type-C
charger.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 60W with zinger, but 90W
when using proper barrel jack adapter on and i7.
Change-Id: If955b9af0e23f47719f001f1d73ec37113937cea
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently bootmode default is set to FSP_BOOT_WITH_FULL_CONFIGURATION
and bootmode UPD is updated in fsp_fill_mrc_cache based on mrc cache data
validity. With current implementation in S3 resume path, if mrc cache
data is invalid, the bootmode is not updated further and remains set
at FSP_BOOT_WITH_FULL_CONFIGURATION. This results in fsp-m to get
incorrect boot mode context and reinitialize memory in S3 resume
path. In correct flow fspm should have correct bootmode context
i.e. S3 resume and return error in case mrc cache data is invalid
or not found.
BUG=b:70973961
BRANCH=None
TEST=Verify correct bootmode is set on S3 resume, even when
mrc cache data is invalid.
Change-Id: Idc0da6ffbfe5ce616d852908a9b0074dc8ce7cbe
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/23156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In S3 resume, for cases if valid mrc cache data is not found or
RECOVERY_MRC_CACHE hash verification fails, the S3 data pointer
would be null and bootmode is set to BOOT_WITH_FULL_CONFIGURATION.
This gets memory to be retrained in S3 flow. Data context including
that of imdr root pointer would be lost, invoking a hard reset in
romstage post memory init. Issuing hard reset before memory init,
saves fsp memory initialization and training overhead.
BUG=b:70973961
BRANCH=None
TEST=Verify S3 resume flows on soraka.
Change-Id: Ibd6d66793ed57c2596d9628c826f6ad198aad58b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The spd.bin file was not getting generated properly, so moved logic
to variant's makefile.
BUG=b:64395641
BRANCH=none
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully and spd.bin is found when booting.
Change-Id: I4642d6ddb5e65f721d1bde31ca0ca5b4438da554
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the 8086:191f North/Host Bridge to the list of definitions.
Adding the definiton makes the Northbridge get recognized by inteltool.
It is found in the Intel i5-6600K CPU:
https://ark.intel.com/products/88191/Intel-Core-i5-6600K-Processor-6M-Cache-up-to-3_90-GHz
Change-Id: Id746d1e8b3bb90b3b68a2f6c372890671dd61b5f
Signed-off-by: Christoph Pomaska <cp_public@gmx.de>
Reviewed-on: https://review.coreboot.org/23055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch fixes 2 edp display issues:
1. When rk_edp_prepare fails >3 times, edp_init isn't run because
while-condition is not satisfied. Then, only a partial init sequence is
ran. This causes all aux transactions to fail.
2. If rk_edp_prepare never succeeds, coreboot never leaves link training
stage due to infinite loop. Boot process is stuck.
TEST=Boot past eDP initialization stage and make sure AP logs don't have
show aux transaction fails.
Change-Id: I44c3f53e8786558c43078d4afe9acde4d64796e7
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/23152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This change adds a call to gspi_early_bar_init in bootblock to
allocate a temporary BAR for any GSPI buses that are accessed before
resource allocation is done in ramstage.
Change-Id: I82387a76d20fb272da6271dd9e5bf2c835d5b146
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22781
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Creating initial common acpi and implement halt.h
BUG=b:71575631
BRANCH=none
TEST=put poweroff() call in Kahlee's mainboard_final and board turns off
correctly
Change-Id: Ie7dd9851dcb240c53f2487b4f4b8a3e51d6b98d6
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/23074
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Now that all the files under util/gitconfig have their license headers,
enable lint-000-license-headers to check the directory too.
Change-Id: I242256f72ac70553535509f83166c6d1ddb16fdc
Signed-off-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/23098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
License header for the `gitconfig.sh` was copied from the Makefile it
was extracted from in commit 9ab8ae6a (util/gitconfig: Make gitconfig
a bash script).
License header for the pre-commit hook names Patrick Georgi as the
copyright holder as he is the original author.
Change-Id: Ie051e5e6ae7571050ece383e6be8236ed7d1ddd9
Signed-off-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/23097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The .spd.hex text is added to the name by the build process. This
was causing a failure because we were trying to add the files:
'file.spd.hex.spd.hex' to the build.
Remove the additional .spd.hex text.
BUG=b:71535311
TEST=Build
Change-Id: I11df7a90c979503676a66c6502900a13f1a8e359
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure
that required SPD hex files are included in the SPD binary.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I449ab56dfc7a75752944b58ba6291b5ee32f81ad
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/22205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Martin Roth