Use of device_t has been abandoned in ramstage.
Change-Id: I8fe817bb514c69a647c2208a0573a2c5fe98722d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Note: For some of the boards affected ACPI S3 support
was never tested but feature was just copy-paste from
reference design.
Change-Id: I2a54d605fa267a7501f57efd79a16b3bfa49891e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Damien Zammit <damien@zamaudio.com>
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All thse Option.*Install.h files are about configuring
what eventually is referenced in the final libagesa
build. It's self-contained so isolate these together
with PlatformInstall.h to hide them from rest of
the build.
Change-Id: Id9d90a3366bafc1ad01434599d2ae1302887d88c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
SSFG was meant to be used as a mask to enable sleep states
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
State _S3 is now set conditionally if HAVE_ACPI_RESUME=y.
For pi/hudson this had been fixed already preprocessor.
Note that all boards had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
States _S1 and _S2 still appear enabled in ASL/AML
but may not actually work.
TEST: 'cat /sys/power/state' and notice choice 'mem' was
removed from the list of available sleep states.
Change-Id: I27d616871c1771f0c87d8fba23d4ce1569607765
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
We define AGESA_LEGACY_WRAPPER a method of calling AGESA
via functions in agesawrapper.c file. The approach implemented
there makes it very inconvenient to do board-specific
customisation or present common platform-specific features.
Seems like it also causes assertion errors on AGESA side.
The flag is applied here to all boards and then individually
removed one at a time, as things get tested.
New method is not to call AGESA internal functions directly,
but via the dispatcher. AGESA call parameters are routed to
hooks in both platform and board -directories, to allow for
easy capture or modification as needed.
For each AGESA dispatcher call made, eventlog entries are
replayed to the console log. Also relocations of AGESA heap
that took place are recorded.
New method is expected to be compatible with binaryPI.
Change-Id: Iac3d7f8b0354e9f02c2625576f36fe06b05eb4ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This replaces the custom environment controller handling in the it8728
driver with the common library.
It also updates the two existing boards with hwm register settings in
their devicetree config so they better match their vendor BIOS fan
control settings.
Change-Id: Idf0c8908ba5ad6ff552b8302bffc638aa9052941
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/19293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We define AGESA_LEGACY as an implementation of mainboard
that has its romstage main completely under mainboard/
directory. We have learnt from other platforms this approach
has several downsides when it comes to making platform-wide
improvements.
We start by creating per-family romstage.c file, which
boards will gradually take into use by removing the
AGESA_LEGACY Kconfig option we here apply to all of them.
Change-Id: Id01931e185a023039a60af16a678de9966db8d65
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18619
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Note that M and M_PRO had same DefaultPlatformMemoryConfiguration
defined, use one for both.
Change-Id: Ia1925957800a7fe6ef511b2d041f7a863c8fc931
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18606
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Status:
- The primary PCIe 16x slot works:
It was tested with a GPU compatible with nouveau
- USB and audio are not very reliable
- The ethernet card is not seen with lspci
- The secondary pcie16x slot isn't working:
When plugging a GPU inside, it's not seen with lspci
- SATA works: The board fully boots GNU/Linux
- Serial doesn't work
- Populating the RAM slots might have to follow
the recommended memory configuration that is described
in the mainboard manual in order to be able to boot.
Note that when running the shutdown command, the default
boot firmware will rewrite part of the boot flash before
powering off the machine.
Flashing coreboot internally from the default boot fimrware can
still work, if the power plug is removed after running flashrom.
Change-Id: I934de521d0acceb7770f23b2ae15c31a67ae73eb
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/16931
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
These definitions do not require AGESA.h include,
and we will eventually remove agesawrapper.h files.
Change-Id: I1b5b78409828aaf2616e177bb54a054960c3869f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18588
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The bare ACPI MMIO address 0xFED80000 was used in multiple
AMD mainboard files as well as the SB800 native code. Reduce
duplication by using a centrally defined value for all AMD
ACPI MMIO access.
Change-Id: I39a30c0d0733096dbd5892c9e18855aa5bb5a4a7
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/18032
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Make the ending comment associated with "chip ...hudson" match the
appropriate directory name.
Change-Id: I5e0d6d41a2e3f963760aad08ed6108acac5b66b3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/17904
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
These headers & comments indicating a lack of functionality don't help
anything. We discourage copyrights and licenses on empty files, so
just clear these.
Change-Id: Id2ab060a2726cac6ab047d49a6e6b153f52ffe6d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17657
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Vendorcode always does PCI MMCONF access once it is
enabled via MSR.
In coreboot proper, we don't give opportunity to make
pci_read/write calls before PCI MMCONF is enabled via MSR.
This happens early in romstage amd_initmmio() for all cores.
Change-Id: If31bc0a67b480bcc1d955632f413f5cdeec51a54
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Replace the use of the old device_t definition inside
mainboard/asus/*.
Change-Id: I5ddfba2102854adcc9bbfd75f7acbe76f0152b72
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16438
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The included file does not declare pm_ioread(), and the
modified file does not call it either.
Change-Id: I9723caf1062db23b4a3648e07c2dc4c02f862619
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14968
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
These files do not use definitions from OptionsIds.h. Also those
definitions are required and already included for Ids.h.
Change-Id: I149fcfe2ad72fe3d7390ee2043a86432aeae3f08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14980
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
File buildOpts.c is a can of worms, pull platform memory
configuration in to OemCustomize.c. This array should be
assigned at runtime instead of linking a modified defaults
table.
Change-Id: I73d9d3fbc165e6c10472e105576d7c40820eaa6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are other things besides PCIe port configuration that
require board specific hooks.
Change-Id: I0923651487b9ed5f6f7569ce08e02d993fa5f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
