GPIO Driver mode is used for configuration interrupt routing for
external devices through GPI. But there is no point in configuring
this for GPO. This patch replaces the PAD_CFG_GPO_GPIO_DRIVER macro
with others that do not set the corresponding bit in the Host Software
Pad Ownership register.
Change-Id: I406a08e526a6c655f38e4c0a355957c98e93881c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Add sc7180 display hardware pipeline programming support
and invoke the display initialization from soc_init.
Changes in V1:
- added display init required check.
- added edid read function using i2c communication.
- added sn65dsi86 bridge driver to init bridge.
- moved display initialization to mainboard file.
Changes in V2:
- moved diplay init sequence to mainboard file
- moved edid read function to bridge driver.
- calculated timing paramters using edid parameters.
- removed command mode config code.
- moved bridge driver to drivers/ti.
- seperated out bridge and soc code with mainboard file as interface.
Changes in V3:
- add GPIO selection at runtime based on boardid.
- add vbif register struct overlay.
Changes in V4:
- update gpio config for lazor board.
Change-Id: I7d5e3f1781c48759553243abeb3d694f76cd008e
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add sn65dsi86 bridge driver to enable the eDP bridge.
Datasheet used : https://www.ti.com/lit/ds/sllseh2b/sllseh2b.pdf
Changes in V1:
- fix the dp lanes using mask
- separate out the refclk and hpd config to init function
Change-Id: I36a68f3241f0ba316c261a73c2f6d30fe6c3ccdc
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add support for display external clock in coreboot for SC7180.
Tested: Display clocks are configured.
Change-Id: Ida222890252b80db738fa1f685b212b3f7c6e689
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Configure GPIO pins as I2S mode for audio speaker.
The audio speaker does not work on Trogdor revision 1, as the
layout was changed.
Developer/Reviewer reference, be aware of this issue:
https://partnerissuetracker.corp.google.com/issues/146533652
Change-Id: Ia4bbfea591a3231640b53e64f0e4e9d43c4437a3
Signed-off-by: vsujithk <vsujithk@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
With the current timeout of 1000 cycles of 100 microsecond would see
timeout occurs on OCP Delta Lake if the log level is set to values
smaller than 8. Because the prink(BIOS_SPEW, ..) in ipmi_kcs_status()
creates delay and avoid the problem, but after setting the log level
to 4 we see some timeout occurs.
The unit is millisecond and the default value is set to 5000 according
to IPMI spec v2.0 rev 1.1 Sec. 9.15, a five-second timeout or greater
is recommended.
Tested=On OCP Delta Lake, with log level 4 cannot observe timeout
occurs.
Change-Id: I42ede1d9200bb5d0dbb455d2ff66e2816f10e86b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45103
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add new memory.c to support DDR4 memory types.
Use the new meminit_ddr() and variant_memory_sku() for eldrid variant
code on memory.c
The initial settings override the baseboard from volteer and fine tune
gpio.c and overridetree.cb on eldrid's configuration.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that Eldrid
can boots. NOTE that tests the ddr4 side of the implementation.
Change-Id: I2c7b30093a8d85bac5aba5b83768af5eb36c4f70
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Allows the AM335X to boot from the coreboot generated MLO by:
- Fixing the load address in the MLO header to be the start of SRAM
- Fixing the way that the bootblock size is calculated (which is
embedded into the MLO so that the MLO knows how much to load into
SRAM). The previous method relied on parsing cbfstool output - the
output has changed format since this was originally written so this no
longer works. Directly using the filesize of the built binary is
probably a more stable way of doing this.
As part of this, the start addresses of SRAM and DRAM were fixed to be
consistent with the AM335x Technical Reference Manual (spruh73, rev Q).
TEST: Booted Beaglebone Black from MLO placed at offset 0x00 on an SD card
Change-Id: I514d7cda65ddcbf27e78286dc6857c9e81ce6f9e
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44381
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The console is initialized before mainboard_init, so the peripheral
should be initialized in bootblock_mainboard_early_init rather than
bootblock_mainboard_init.
Change-Id: I9f4ba29798eb0b1efea76f5ade4a234fb35a2f83
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This is an intermediate step to have SOC_INTEL_COMMON_BLOCK_CPU select
CPU_INTEL_COMMON directly, to avoid dependency problems.
Tested with BUILD_TIMELESS=1: Without including the config file in the
coreboot.rom, both OCP Tioga Pass and Delta Lake remain identical.
Change-Id: I565e75869be730e7c2fe7114b829941bc9890e6c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45041
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This ports Linux commit 71f677a91046599ece96ebab21df956ce909c456
"Handle configuration without P2A bridge".
Quote:
The ast driver configures a window to enable access into BMC
memory space in order to read some configuration registers.
If this window is disabled, which it can be from the BMC side,
the ast driver can't function.
Closing this window is a necessity for security if a machine's
host side and BMC side are controlled by different parties;
i.e. a cloud provider offering machines "bare metal".
P2A stands for primary to AHB.
Tested on Prodrive Hermes, which uses an AST2500. The machine still
boots, has a high resolution framebuffer working in EDK2, and its
boot time has been reduced by 2.5 seconds as it no longer runs into
a timeout due to disabled P2A bridge.
Change-Id: I3293dc35ae89c010154e02eff904ec3a68c96683
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fixes complains about missing INT configuration by the pciexp kernel
modules.
Tested with Linux 5.5 on Prodrive Hermes.
Change-Id: I277f592cd8d2c86a9c7ba4b34d3f703f7d593582
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The three Intel Apollo Lake boards (apl_rvp, leafhill and minnow3) do
not define MAX_CPUS, which would then default to 1. Since this is most
likely an oversight, use the same value as other Apollo Lake boards.
To ensure this does not happen again, factor out MAX_CPUS to SoC scope.
Change-Id: I5ed98a6b592c8010b59eca7ff773ae1ccc4cd7b1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APL does not support Hyper-Threading, and has at most four CPU cores.
Change-Id: Ib2ffadc0c31cdd96bec8eed5364c984acb2e1250
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45143
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update critical and passive policy for TSR0.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I244e1b5cacabf5b73c47b4039ae150cd17fcd0fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45169
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sushi is not a real product, just a test of the new_variant program.
The effort to keep it up-to-date with the rest of Hatch is no longer
worth it. Remove the variant.
BUG=b:168030592
TEST=build bot is successful, hatch-cq builds successfully
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I2b0036f3cbdea4bfaed1274ab87a20d24c75de57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CB:44774 introduced the non-existent SPD path. This is preventing the
device from booting up.
BUG=b:168053219
TEST=Build and boot drawcia board to OS.
Change-Id: I70ca5f4cf2c8e2e88ea5b1514b656caafb732743
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
SMBus code is linked unconditionally since commit 0e3c59e. This change
drops that obsolete part from the help text.
Change-Id: I603ab012760684021be1b5eca5d0ddff69463b79
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Instead of generating hexdumps, output binary SPD files since we plan to
convert all hex SPD files to binary. Also adjust the file extension
where needed.
Test: compared generated binaries with converted binaries from hex files
Change-Id: Ie99d108ca90758d09dbefad20fe6c9f7fc263ef1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Passing binary SPD files to apcb_edit can lead to an encoding error,
since the files were read in text mode. To fix this, read SPD files
always in binary mode and only decode them, when `--hex` is set.
Tested by comparing output files from the same SPDs in both, binary and
hex mode.
Change-Id: I6b75a9e1234e71667bdc8cb4eb10daf8c0ac3c17
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Most of them are needed for SMBIOS type 17 creation.
Tested=With FSP WW36 verified the printed hob values match
with FSP hob data.
Change-Id: I02f4600f1be39e2576d7c84a5a6b6672ebb7034b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44847
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Support SPI flash dual read funciton which change spi mode (1-1-1)
to dual mode (1-1-2).
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: Iabd3668fc4bc42137b7743144fc1cced4fe72737
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44852
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To minimize the quirks the kernel has to apply, the headset mic is set
to its correct value in coreboot.
Tested on lemp9, audio is functional.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I6b59de95f01360a5f7779f87f39edeb75dedc215
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43631
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Maxim Polyakov