The number at the end actually means the max MiB/s. So 52 MHz clock @ 8x
data width, sampled on each clock edge = 104 MiB/s.
According to JEDEC Standard No. 84-B51A (JESD84-B51A), maximum bandwidth
& clock frequency for various MMC bus speed modes are (at x8 bus width):
MMC_Legacy: 26 MB/s at 26 MHz Single Data Rate (SDR)
MMC_HS: 52 MB/s at 52 MHz SDR
MMC_DDR52: 104 MB/s at 52 MHz Dual Data Rate (DDR)
MMC_HS200: 200 MB/s at 200 MHz SDR
MMC_HS400: 400 MB/s at 200 MHz DDR
BUG=b:159823235
BRANCH=zork
TEST=build zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7818d8cb5ed5974c60a900477a0aa2ecc904db0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48309
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due the location of X86_RESET_VECTOR, the anchor point
for linking the bootblock is at the end, which equals
ROMSTAGE_ADDR.
Change-Id: I2d25911582393c9a10fd3afa1a484eda2604d95a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The architectural requirement is for the address to be
located at the end of bootblock -0x10 bytes, so the
definition was redundant with other Kconfig variables.
Change-Id: Ia014470cfadf0b401a12a2de6dce3b1fc1862137
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change adds support to lock down the DMI configuration
in dmi_lockdown_cfg() by setting Secure Register Lock (SRL)
bit in DMI control register.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I98a82ce4a2f73f8a1504e5ddf77ff2e81ae3f53f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48258
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change reorganizes FMAP for volteer to make use of the lower
16MiB of the SPI flash for RW_SECTION_A and RW_MISC in addition to
RW_LEGACY. This is now possible because TGL supports memory mapping of
BIOS region greater than 16MiB.
Following changes are made in chromeos.fmd as part of this:
1. Move RW_SECTION_A and RW_MISC to lower 16MiB.
2. Reduce size of RW_LEGACY to 2MiB since we longer need to use it as
a placeholder in the lower half of the SPI flash.
3. Reduce size of RW_ELOG to 4KiB as coreboot does not support a
larger region for ELOG.
4. Increase WP_RO to 8MiB to allow larger space for firmware
screens. GBB size is thus increased to 448KiB.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I0c3c0af94183a80c23d196422d3c8cf960b9d9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change enables support for extended BIOS window by selecting
FAST_SPI_SUPPORTS_EXT_BIOS_WINDOW and providing base and size of the
extended window in host address space.
BUG=b:171534504
Cq-Depend: chromium:2566231
Change-Id: I039155506380310cf867f5f8c5542278be40838a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
AP_PEN_DET_ODL isolated by a diode and need to pull up internally.
BUG=b:160752604
BRANCH=dedede
TEST=Build and confirm waveform by google EE parter.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I85f3d0209094af07891a5c0cc218443da586e6e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48294
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the PMC MUX and CONx devices for adlrvp for
conn2.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I52afbd429750cfa416f4ed93aeb1be590f8c3a5c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48230
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ramstage parts gets renamed to fch.c and the bootblock one to
early_fch.c. No functionality from the old southbridge file is used in
romstage, so don't link it there.
Change-Id: I7ca3b5238c3b841191dd0459996b691edd76fbf8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Since mmio_util gets also linked into verstage on PSP, all-y can be used
here.
Change-Id: I03572d760b485938f0d00b6cead00746eda6ca09
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48436
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace sb prefix with fch prefix, since those are all FCHs and no south
bridges any more. Verstage on PSP uses the I/O access mechanism instead
of the MMIO one, so keep a separate function for that, but also move it
to the common mmio_util file to have them all in one place.
Change-Id: I47dac9ee3d9e27f7b7a5fddab17cf4fc10de6c3e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48435
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the setup of the base address to a separate function and explicitly
set the SMBUS and ASF I/O port decode even though it is expected to
already be set after reset.
Change-Id: I8072ab78985021d19b6528100c674ecdd777e62e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
ACPIMMIO_DECODE_REGISTER_04 is the definition in the common ACPIMMIO
code block that actually gets used. Also fix the indentation of the
ACPIMMIO register decode defines in the common code.
Change-Id: Ib2c460541be768fe05d8cc3d19a14dbd9c114a45
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
sb_disable_4dw_burst is only used in the same compilation unit, so no
need to make it externally visible.
Change-Id: I6c7c96f67b98fb8ed808f45a7685c4d72a10d32c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change restricts RW_DIAG region to lower 16MiB to ensure that the
extended BIOS checker for FMAP does not complain about 16MiB boundary
crossing.
I haven't updated any other regions to occupy the newly freed space
but it is fine since this board is dead and should be dropped from
coreboot soon.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I19ab204fbe3e020e42baf68bfa350dcff32066a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change restricts SI_ME region to live below the 16MiB boundary to
ensure that no regions cross the 16MiB boundary as the extended BIOS
window checker for FMAP complains about it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib0838ff4c63b06b8dc169b40d3022965b2f2f8f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change adds support to Lock down the configuration of
extended BIOS region. This is done as part of
fast_spi_lockdown_cfg() so that it is consistent with the
other lockdown.
Change includes:
1. New helper function fast_spi_lock_ext_bios_cfg() added that
will basically set EXT_BIOS_LOCK.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I730fc12a9c5ca8bb4a1f946cad45944dda8e0518
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48068
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables caching for extended BIOS region.
Currently, caching is enabled for the standard BIOS region
upto a maximum of 16MiB using fast_spi_cache_bios_region,
used the same function to add the support for caching for
extended BIOS region as well.
Changes include:
1. Add a new helper function fast_spi_cache_ext_bios_window()
which calls fast_spi_ext_bios_cache_range() which calls
fast_spi_get_ext_bios_window() to get details about the
extended BIOS window from the boot media map and checks for
allignment and set mtrr.
2. Make a call to fast_spi_cache_ext_bios_region() from
fast_spi_cache_bios_region ().
3. Add new helper function fast_spi_cache_ext_bios_postcar()
which does caching ext BIOS region in postcar similar to 1.
4. If the extended window is used, then it enables caching
for this window similar to how it is done for the standard
window.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I9711f110a35a167efe3a4c912cf46c63c0812779
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47991
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds the SPI-DMI Destination ID for tigerlake
soc. This is needed for enabling support for extended
BIOS region. Also, implements a SOC helper function
soc_get_spi_dmi_destination_id() which returns SPI-DMI
Destination id.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0b6a8af0c1e79fa668ef2f84b93f3bbece59eb6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change enables support for configuration of extended BIOS
region decode window. This configuration needs to be performed
as early as possible in the boot flow. This is required to
ensure that any access to the SPI flash region below 16MiB in
coreboot is decoded correctly. The configuration for the extended
BIOS window if required is done as part of fast_spi_early_init().
Changes include:
1. Make a call to fast_spi_enable_ext_bios() before the bus master
and memory space is enabled for the fast SPI controller.
2. Added a helper function fast_spi_enable_ext_bios() which calls
fast_spi_get_ext_bios_window() to get details about the extended
BIOS window from the boot media map.
3. Depending upon the SPI flash device used by the mainboard and
the size of the BIOS region in the flashmap, this function will
have to perform this additional configuration only if the BIOS
region is greater than 16MiB
4. Adddditionally, set up the general purpose memory range
registers in DMI.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Idafd8be0261892122d0b5a95d9ce9d5604a10cf2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47990
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change allows configuring the General Purpose
Memory Range(GPMR) register in BIOS to set up the decoding in DMI.
This driver provides the following functionality:
1. Add a helper function dmi_enable_gpmr which takes as input base,
limit and destination ID to configure in general purpose memory range
registers and then set the GPMR registers in the next available
free GMPR and enable the decoding.
2. Add helper function get_available_gpmr which returns available free
GPMR.
3. This helper function can be utilized by the fast SPI driver to
configure the window for the extended BIOS region.
BUG=b:171534504
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I34a894e295ecb98fbc4a81282361e851c436a403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47988
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds details about the memory map windows to translate
addresses between SPI flash space and host address space to coreboot
tables. This is useful for payloads to setup the translation using the
decode windows already known to coreboot. Until now, there was a
single decode window at the top of 4G used by all x86
platforms. However, going forward, platforms might support more decode
windows and hence in order to avoid duplication in payloads this
information is filled in coreboot tables.
`lb_spi_flash()` is updated to fill in the details about these windows
by making a call to `spi_flash_get_mmap_windows()` which is
implemented by the driver providing the boot media mapping device.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I00ae33d9b53fecd0a8eadd22531fdff8bde9ee94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48185
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change reserves the window used for extended BIOS decoding as a
fixed MMIO resource using read_resources callback in systemagent
driver. This ensures that the resource allocator does not allocate
from this window.
Additionally, this window is also marked as fixed memory region in
_CRS for PNP0C02 device.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I42b5a0ebda2627f72b825551c566cd22dbc5cca7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change enables support for a custom boot media device in fast SPI
controller driver if the platform supports additional decode window
for mapping BIOS regions greater than 16MiB. Following new Kconfigs
are added:
1. FAST_SPI_SUPPORTS_EXT_BIOS_WINDOW: SoC can select this to indicate
support for extended BIOS window.
2. EXT_BIOS_WIN_BASE: If FAST_SPI_SUPPORTS_EXT_BIOS_WINDOW is
selected, this provides the base address of the host space that is
reserved for mapping the extended window.
3. EXT_BIOS_WIN_SIZE: If FAST_SPI_SUPPORTS_EXT_BIOS_WINDOW is
selected, this provides the size of the host space reserved for
mapping extended window.
If platform indicates support for extended BIOS decode window,
cbfstool add command is provided additional parameters for the decode
window using --ext-win-base and --ext-win-size.
It is the responsibility of the mainboard fmap author to ensure that
the sections in the BIOS region do not cross 16MiB boundary as the
host space windows are not contiguous. This change adds a build time
check to ensure no sections in FMAP cross the 16MiB boundary.
Even though the platform supports extended window, it depends upon the
size of BIOS region (which in turn depends on SPI flash size) whether
and how much of the additional window is utilized at runtime. This
change also provides helper functions for rest of the coreboot
components to query how much of the extended window is actually
utilized.
BUG=b:171534504
Change-Id: I1b564aed9809cf14b40a3b8e907622266fc782e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There have been a few issues with the new CBFS mcache code in stages
after romstage, where the mcache resides in CBMEM. In a few special
cases the stage may be doing a CBFS lookup before calling
cbmem_initialize(). To avoid breaking those cases, this patch makes the
CBFS code fall back to a lookup from flash if CBMEM hasn't been
reinitialized yet in those stages.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icf6d1a1288cb243d0c4c893cc58251687e2873b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
cbmem_online() always returns 1 in stages after romstage. However, CBMEM
isn't actually immediately available in those stages -- instead, it will
only become available when cbmem_initialize() is called. That usually
happens very early in the stage, but there are still small amounts of
code running beforehand, so it is useful to reflect this distinction.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I623c0606a4f49ea98c4c7559436bf32ebb83b456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds the PMC MUX and CONx devices for lindar. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:172533907
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id5ee78b7ece8421144086af9b95f5f0d849be56c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
SATA_AHCI is already the default mode for CNL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I814e191243224a4b021cd7d4c1b611316f1fd1a4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Align the SATA mode names with soc/skl providing a consistent API.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I54b48462852d7fe0230dde0c272da3d12365d987
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The PCI devices P2SB and PMC are hidden by the FSP and cannot be
unhidden, because the FSP locks their configuration. Thus, setting them
to `on` is not correct. Therefore, set their state to hidden.
Change-Id: Ib7c019cd7f389b2e487829e5550cc236ee5645b7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds optional CBFSTOOL_ADD_CMD_OPTIONS that can be used by
arch/SoC/mainboard Makefiles to supply any additional arguments that
need to be passed into cbfstool when using cbfstool add command.
This is useful when platform wants to add these parameters depending
upon some arch/SoC/mainboard specific configs. Immediate use case is
the fast SPI controller on Intel platforms adding arguments for
extended window base and size.
BUG=b:171534504
Change-Id: I2f48bc3f494d9a5da7e99b530a39d6078b4a881c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47884
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Skylake FSP isn't used by coreboot anymore. Therefore, drop the
misleading comment and the "KBLFSP" extension from the names of these
enums.
Also, drop the "MODE" extension to make their names shorter in general,
since it doesn't add any more value.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: If37d40e4e1dfd11e9315039acde7cafee0ac60f0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48377
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use proper indents in the devicetree and align `end` keywords.
Change-Id: Id6e6f4ad648a9bed35305b7a446744c6ed06a150
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48372
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCI devices P2SB and PMC are hidden by the FSP. So instead turning
them off, set their state to hidden being able to allocate ressources
for them.
Change-Id: Ie6e12f99b0a7ffb1c4831b3aa8705e911b677e88
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48371
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update lindar gpio settings for Synaptics trackpad no function issue.
Update I2C5 bus freq to 400kHz.
Improve Goodix Touchscreen power on sequence.
BUG=b:160013582
BRANCH=firmware-volteer-13521.B
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device. Verify trackpad function workable.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I8c1ab6bab1f9de187e2a78ead7b5bbaf758f5fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Raul E Rangel