The WP signal to the AP isn't inverted as it is on other platforms, so
it was reporting incorrectly. Change the ACPI table to be active low,
and invert the signal when reporting it to everything else.
BUG=b:74946358
TEST=Boot grunt with battery inserted, WP signals both report 1. Remove
battery, WP_CUR reports 0, WP_BOOT still reports 1.
Change-Id: Ic1369dbda609e34b308af308880449643be6af39
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This allows compiling the program using musl-libc, since otherwise
iopl(2) is undeclared.
Change-Id: Ia27203cf47b9be3f7bf1ad422c8f490caeae8f56
Signed-off-by: Ivan J. <parazyd@dyne.org>
Reviewed-on: https://review.coreboot.org/23834
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch sets PL1 value to ~6W. Here, 8W setting gives
a run-time 6W actual measured power.
Also, this patch sets PL2 value to 15W.
BUG=None
BRANCH=None
TEST=Build and read the MSR 0x610.
Change-Id: I2439a49b9917db0d9b05f333ce1c35003da493f6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/25341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is hopefully more readable.
TEST=Build lenovo/x200 with and without this patch (using make
BUILD_TIMELESS=1), compare build/coreboot.rom, notice no differences.
Change-Id: I079d5353633a3d58ce0e5e616f3fad687a064d65
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23709
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch selects `HAVE_APCI_RESUME` to enable S3 resume. This
has a dependency on EC to store the hash.
BUG=b:72472969
TEST=suspend and resume from S3 should work.
Change-Id: I9de84dfd450936b3bc08e016bec6cf5ae88eab3d
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25390
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copy strrchr from libpayload.
To be used by Cavium's BDK or FDT parsers.
Change-Id: Iab7981c25113ed16f1b8130de4935d30c29d2fa5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Sometimes when bringing up a new board it can take a while until you
have all the peripheral drivers ready. For those cases it is nice to be
able to bitbang certain protocols so that you can already get further in
the boot flow while those drivers are still being worked on. We already
have this support for I2C, but it would be nice to have something for
SPI as well, since without SPI you're not going to boot very far.
This patch adds a couple of helper functions that platforms can use to
implement bit-banging SPI with minimal effort. It also adds a proof of
concept implementation using the RK3399.
Change-Id: Ie3551f51cc9a9f8bf3a47fd5cea6d9c064da8a62
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The <gpio.h> API is supposed to include a gpio_set() function that just
toggles the state of a GPIO already configured as an output, even though
we rarely need it since gpio_output() can already be used to initialze a
GPIO to a default value while configuring it as an output. This function
was forgotten on Rockchip, so this patch adds it now.
Change-Id: I201288139a2870e71f55a7af0d79d4a460b30a0c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
BUG=b:77345148
TEST=Pull power from grunt, verify CMOS power failure is detected.
Reboot and verify that CMOS power failure is not detected.
Change-Id: Idbf0254e197a6d282e618a98bced52ea5a44917f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25468
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change f43adf0 (intel/common/block/cpu: Change post_cpus_init after
BS_DEV RESOURCES) moved post_cpus_init to BS_OS_RESUME for S3
path. This results in BSP timing out waiting for APs to be
parked. This change increases the time out value for APs to be parked
to 250ms. This value was chosen after running suspend-resume stress
test and capturing the maximum time taken for APs to be parked for
100 iterations. Typical values observed were ~150ms. Maximum value
observed was 152ms.
BUG=b:76442753
TEST=Verified for 100 iterations that suspend-resume does not run into
any AP park time out.
Change-Id: Id3e59db4fe7a5a2fb60357b05565bba89be1e00e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
google_chromeec_command() may only write the 1 or 2 bytes to
variable r (4 bytes). However, this api returns 4 bytes data.
To avaid returning the incorrect data, we need to initialize the
local variable.
BUG=b:76442548
BRANCH=none
TEST=write 2 bytes data into the flash, then, read by cbi_get_uint32
Change-Id: I3395c97ab6bfd7882d7728310de8a29041190e76
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25460
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case of all DMI Type 17 to be empty, the strip trailing whitespace
code will have a zero length Part Number entry, which will cause
exception when using (len - 1) where len is zero. Add extra code to
cover this corner case.
BUG=b:76452395
TEST=Boot up fine with meowth platform, without this patch system will
get stuck at "Create SMBIOS type 17".
Change-Id: Id870c983584771dc1b60b1c99e95bbe7c0d25c4c
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25377
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to save the ACPI OpRegion table
address in ASLB, and restore table address upon S3 resume.
Implementation modeled on existing Baytrail code.
Test: boot Windows 10 on google/chell with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: Icd6b514e531eec6e49dbb03eb765144f41c1e31b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to save the ACPI OpRegion table
address in ASLB, and restore table address upon S3 resume.
Implementation modeled on existing Baytrail code.
Test: boot Windows 10 on google/edgar with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: I7c1fbf818510949420f70e93ed4780e94e598508
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Get rid of custom opregion implementation and use drivers/intel/gma/opregion
implementation instead.
Test: boot Windows 10 on google/chell and google/edgar using Tianocore
payload with GOP init, observe Intel graphics driver loaded and functional.
Change-Id: I5f78e9030df12da5369d142dda5c59e576ebcef7
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21703
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
me_progress_rom_values array provides detailed information maps to ME
HFSTS2 register value.
There is a chance that ME status value might be over the size of
me_progress_rom_values.
This commit adds a check before access the array.
BUG=b:77247550
Change-Id: I5de569c62b94b0595d3d3ea254f50e312e8c11a4
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/25425
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new variant of Poppy for the Atlas board.
BUG=b:75454415
TEST=tested on a P0 board. System boots and is mostly
functional, though some peripherals are not ready so there
are no touchpad/touchscreen devices configured yet.
Change-Id: I5a0bccd1bda0134aa51885ac2c6e7bb5b45de924
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change updates devicetree and GPIO configurations to match the
schematics:
1. pcie_rp...[2] is the one being used for wifi, thus, clk_req and
deemphasis_enable for [2] need to be set instead of [0].
2. WLAN power enable, wifi disable and PERST# GPIOs need to be
configured correctly.
BUG=b:76180142
TEST=Verified that wlan0 scan works.
Change-Id: Ic51a94902e2cac3491081ade32079e5b88719f45
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This moves the sandybridge both smm setup and smihandler code to a
common place.
Tested on Thinkpad X220, still boots, resume to and from S3 is fine
so smihandler is still working fine.
Change-Id: I28e2e6ad1e95a9e14462a456726a144ccdc63ec9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This enables ThunderPeak WiFi card on M.2.
TEST=Verify wlan card shows up in lspci
Change-Id: I5b3f871bdc67bfc4ed283b997b2a5698451b2bd2
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/24931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable VMX if supported by CPU and enabled in board devicetree.
Check lock bit unset before enabling VMX.
Change-Id: Ic57eac45e9c65baa4479735c6d70a7eb685f080e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb.
Change-Id: I34e7d750d3f75757a68977ae8d92bfbee1a10af1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
Change-Id: I5aea15511c52d1191babf551feb237f4144683e4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When CONFIG_VBOOT is enabled then the xDCI controller should only be
enabled if the system is in developer mode. This prevents a system
in normal/verified mode from being used as a USB peripheral device
which could potentially be used to access user data.
This change adds a function to return whether xDCI can be enabled
or not, which will be used by the SOCs.
Change-Id: Ie3ee9dd7077c094a01fd857a2e4033a12ce8979b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch disables debug consent in the devicetree. When debug
consent is set to DBC by default, it prevents some clocks from turning
off during S0ix. This blocks S0ix entry.
This patch also enables S0ix from the devicetree.
BUG=b:76163091
TEST=enter S0ix and check if slp_s0 is asserted
Change-Id: I05001a41b13e7784c34fa8f1f773fb94bbdcd01f
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25312
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the NHLT configuration for the max98373 codec to skylake,
taken directly from cannonlake.
This will allow skylake/kabylake boards to use this codec.
Change-Id: Ifb6bf2d31fda25b18d9b1ce2bb721255335d55e4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds a call to heci_reset before attempting to read
ME firmware version. This is important to ensure that both ME and BIOS
are in sync.
BUG=b:76167737
BRANCH=poppy
TEST=Verfied that ME firmware version read does not fail on first boot
after power failure (i.e. removing battery and AC power).
Change-Id: Ib6b39c398d2e1177b087352a4acb8bcf5a9897d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Current emmc tuning parameters for octopus were copied over from other
boards and result in failure to boot from emmc. This change gets rid
of the emmc tuning parameters in devicetree. Once emmc tuning tests
are run for octopus, these parameters can be added back.
BUG=b:75986903
BRANCH=None
TEST=Verified that octopus boots from eMMC without any errors in
depthcharge.
Change-Id: I7ac44a54afd1ecfe355a9654ac8e92133b67637f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch changes the GBB flag configuration to the latest usage in
upstream vboot (as of https://chromium-review.googlesource.com/976660).
Change-Id: I585d662d7de34b4964d028e3d06b4df5665fbe9e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The EC needs to set the PPCM value depending on whether
Turbo is enabled or not, and the values differ between
Broadwell (0, 1) and Skylake (1, 2) platforms.
Change-Id: I662dce54415e685c054ffc00b6afde0f1f7765e2
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The LPC I/O ports for EC communication were not set properly,
causing ectool to fail to read the Index I/O from the EC.
The EC Index I/O is on port 0x380 and the LPC I/O port needs to be
decoded by the PCI device for it to be accessible.
Correct the value for the Librem 13v1, 13v2 and 15v3.
Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change remove work-around code for the power issue of MIPI and
USB cameras on previous board revision. With the work-around code,
PMOF ACPI method cannot turn off MIPI camera. So we need to remove
it.
BUG=b:74214248
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/25337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The code is based on autoport and that for revolve_810g1
Tested:
- CPU i5-3437U
- Slotted DIMM 8GiB
- Onboard USB2 interfaces (wlan slot, wwan slot, camera, smart card)
- Mini pci-e on wlan slot
- On board SDHCI connected to pci-e
- USB3 ports
- USB3 hub on dock (connected to USB3 port 1)
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.13.17-1 within Debian GNU/Linux testing, loaded from
SeaBIOS, or Linux payload (Heads)
Not tested:
- Fingerprint reader on USB2
Not working well:
- EHCI debug on port SSP2,(The USB port on the left, wired to ehci
before OS) it has always-on enabled by default (maybe via EC),
which disturbs FT232H's own power up, requiring a very critical
timing to plug it in for it to work.
Change-Id: I52e549ec18e8aa661a506a16dbc7f83417c0da78
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/25218
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=build
Change-Id: I32d185741ce20a3a82e6895de3026ade52d0bcc8
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
TEST=build
Change-Id: Ie54e310a94f61b8d86c13261937015e3f5a2ab01
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
A change introduced by commit fe4983e5 [1] in order to prevent
re-initialization of the TPM if already set up in verstage
had the wrong logic in the if statement, causing the TPM
to never be initialized if vboot is disabled.
The RESUME_PATH_SAME_AS_BOOT config is enabled by default for
ARCH_X86, resulting in the if statement to always evaluate to
false. Remove that condition from the if statement to allow it
to function as intended.
This patch also enables TPM initialization for FSP 2.0 with
the same conditions.
[1] intel/fsp1_1: Do not re-init TPM in romstage if already setup in verstage
https://review.coreboot.org/#/c/coreboot/+/14106/
Change-Id: Ic43d1aa31a296386c7eab6d997f9b701e9ea0fe5
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23680
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the support for KBL-S MCH and Z270, H270, B250 and
Q250 PCH chips.
BUG=None
BRANCH=None
TEST=Boot with KBL-S CPU and B250/H270 PCHs.
Change-Id: If03abb215f225d648505e05274e2f08ff02cebdc
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/25305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
In an attempt at consolidation, commit 0a203d1 [1] introduced
an additional read/write of the MISC_ENABLE msr, as well a bug
which nullified the setting of Intel SpeedStep by inserting said
read/write calls in between another set of read/write calls to the
same msr. Fix by reverting to previous (simpler) implementation.
[1] soc/intel/skylake: Use CPU common library code
https://review.coreboot.org/19566
Test: boot Linux on Librem13v2, read MISC_ENABLE msr and verify
SpeedStep bit correctly set based on devicetree setting.
Change-Id: Id2ac660bf8ea56d45e8c3f631a586b74106a6cc9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Martin Roth