Some settings like direction are only used if the mode is GPIO.
Change-Id: I4efc54dfef3721b528b90d49f490014d9132cdf8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28627
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that the last dependency was resolved, remove AmdLib folder.
BUG=b:112525011
TEST=Build and boot grunt.
Change-Id: Ibd9a20bc358742520138b9b01f76d7fd2fac92ab
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28742
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This board is pretty much like the G41M-GS, but with DDR3 memory
instead. The PCB layout is almost identical.
What works:
- S3/S4 resume
- RAM init
- Booting to Debian
- Display lights up w/ libgfxinit
- Both PS/2 work
- Ethernet
- Graphics card on PEG
- USB
- SATA ports
- NVRAM debug_level
- Internal flashing
- PCI slots (tested with CT4810 audio card)
- fancontrol (Only CPU fan can be regulated)
- Audio (Rear ports only)
What does not work:
- Hell knows what might be wrong
What is not tested:
- PCIe x1
- IDE
- Floppy
- Parallel port
Change-Id: I66b216af740680c390ea82e4fe07737c20227cc6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The function to fill out the FADT table exits early if the devicetree
config option to disable the legacy timer is set. This means it never
gets to the later check for s0ix config option and so the flag to
indicate that it supports low-power idle in S0 is not set.
Change-Id: Ia0416f21b6445f6feecb6f0301d48fdf2522b8a6
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/28755
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Gigabit Ethernet network controller on whiskey lake rvp platform,
add NVM bin file as well.
BUG=N/A
TEST=Build and boot up into chromeos on whiskey lake rvp platform, and
check eth0 can get IP address assigned,
Change-Id: Ia299a2aa78108175074e084cc34a7d2b38cf1c72
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27848
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SkipMpInit UPD had ben moved from Fsp SiliconInit UPD to Fsp MemoryInit
UPD, hence change the settings in coreboot side as well. The old options
in SiliconInit get deprecated, so leave the code as is will be
harmless. Make the changes limited to coffeelake itself.
Change-Id: If968de78117068668e4f0006c412442c50658ba9
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28740
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sphinx displays a tab as four spaces, which makes code indented with
eight spaces per level stand out. Format the example configuration file
in fit.md consistently with tabs to make it look consistent everywhere.
Change-Id: Ia1d4c44e68e5267bac1f0f558421c6a0c7a9329c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Some of the FSP silicon UPD entry can be updated base on device switch
in pci device tree, have both static config setting and device tree "on"
and "off" will be redundant.
BUG=N/A
TEST=Build and boot up fine with Whiskey Lake RVP platform.
Change-Id: Ia36cfab03c4613786e5580a039d89007b630adf9
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27766
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change is required to apply patch
06_CorebootPayloadPkg_keep_cb_table since conflict in white space
between patch and target file in edk2 makes patch rejected while
building under coreboot-sdk:1.52.
Change-Id: I38f7d46925cc00a2b5c5400e3fbf3579990f3fa5
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Martin Roth <martinroth@google.com>
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
This mainboard is based on mc_apl1. In a first step, it contains a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl2 mainboard will follow in separate commits.
Change-Id: I0af60ab0dfe556dd95da2cf1a49c685a8f0ae4eb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
In preparation for a future MC Apollo Lake board which will be equipped
with LPDDR4 modules, it is necessary to make the swizzle data
configurable. Starting from the mc_apl1 baseboard, which is equipped
with DDR3L memory and therefore does not need swizzle data, the
structures are initialized with zero.
Change-Id: I4954d0a00d1d5fc28a8dda45a9fb27f98d5c3f1e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Increase power limit1 maximum value from 5W to 7W. This value as per
recent measurement on closed system which shows better performance
results.
BUG=None
TEST=Build and tested on Nocturne system. Performance tests
show better results.
Change-Id: I7485b1d2afde46ec28d548c13be35a43e7572918
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The previous does not work well enough when testing with
high ambient temperature. Update DPTF settings to make
it work better.
List of tweaks:
1. Raise DRAM Critical temperature from 48C to 55C
Note that there are mechanisms in EC that complement
this because of DPTF limitation that we can't have
multiple passive temperatures.
2. Lower response time for DRAM temp sensor from 60s to 5s.
3. Increase throttle priority to the charger when DRAM hit
passive temperature from 100 to 200.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: Idf7efa76b2c6085cf97aa9f65c6ce066e8cff99a
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28738
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These parameters are not used and not necessary in sdram.c, because the
DDR PLL is configured in clock.c.
Change-Id: I8060bd21e05765cedf7bdabc28052c32774f9ca1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28710
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After emulating an instruction in the misaligned load/store handler, we
need to increment the program counter by the size of instruction.
Otherwise the same instruction is executed (and emulated) again and again.
While were at it: Also return early in the unlikely case that the
faulting instruction is not 16 or 32 bits long, and be more explicit
about the return values of fetch_*bit_instruction.
Tested by Philipp Hug, using the linuxcheck payload.
Fixes: cda59b56ba ("riscv: update misaligned memory access exception handling")
Change-Id: Ie2dc0083835809971143cd6ab89fe4f7acd2a845
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This part of our documentation has bitrotted for a long time.
Any remaining information should ideally be moved to
Documentation/getting_started/kconfig.md.
Change-Id: I3920d002813c2838285446dc0ed8dacfa5364581
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28665
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that PspBaseLib is no longer used, fully remove the folder.
BUG=b:116579642
TEST=Build grunt
Change-Id: I441b3f46e2312c12771766f87b25d1dc15ff3af0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
FIT payloads do not support compression. Currently this would thrown an error
like the following:
E: FIT images don't support whole-image compression, compress the kernel component instead!
With this patch, menuconfig will correctly *not* show payload compression for
FIT payloads, and this will correctly set compression to NONE.
Change-Id: If564e2f5c0d499bc30411d7bd41611790453d4ef
Signed-off-by: Andrea Barberio <insomniac@slackware.it>
Reviewed-on: https://review.coreboot.org/28732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The Cheza board contains a couple of non-standard FMAP sections that
contain per-board calibration data. When flashing new firmware to the
board, care should be taken to copy these sections over so that all
features can still function correctly afterwards. This patch wraps a new
RO_PRESERVE FMAP section around these sections to make them easier to
preserve as a group.
Change-Id: I77919336f609a1be399598736f46921c3da99e68
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Configuration of pins exposed by superIO are inconsistent between board
variants. Each platform should have UARTs enabled, this is expected
behaviour of these pins. Given that APU2_PINMUX_UART_x can be set for
all boards as default.
Change-Id: Ifb7dfe23a95ba0e572adc38212333d9fdd234d53
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
My CPU (3770k) supports 9 MCE banks, but the code is hardcoded to reset
only 7. This causes Linux to spuriously log errors during boot and S3
resume.
Fix this by reading the real value from the right MSR.
Change-Id: Id05645009259fd77b4de49bde518361eeae46617
Signed-off-by: Dan Elkouby <streetwalkermc@gmail.com>
Reviewed-on: https://review.coreboot.org/28443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This board doesn't support the newest RISC-V Privileged Architecture
spec (1.10), and it's based on an FPGA so it's a moving target.
Now that there's actual RISC-V silicon out there (from SiFive),
mb/lowrisc/nexys4ddr will only continue to bitrot.
Change-Id: I4e3e715106a1a94381a563dc4a56781c35883c2d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Need to tune I2C bus 6 clock frequency under the 400KHz
Bug=b:116543001
TEST=flash coreboot to the DUT and measure I2C bus 6 clock
frequency whether arrive to 399.1KHz
Change-Id: I95b535a6b429fc34961a4953004a1c51e53a9be6
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28747
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since I2C bus 7 attached the touchscreen device however Phaser units
that haven't it. So for avoiding side effects, we need close I2C bus
7 SCL and SDA respectively.
BUG=none
TEST=according to sku_id (Phaser: 0x1, Phaser360: 0x2, Phaser360s: 0x3)
distinguish whether close these gpios.
Change-Id: I8ad17761f2a053dc329bbec0a0a3284d47289666
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28669
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since each variant has a separate build, we don't need to support
multiple manufacturers in a single file.
BUG=b:79874904
TEST=Build, boot, see updated mainboard manufacturer
Change-Id: I0ccf207ba8d5e5200aa4b19c46784bbda82f7b6e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
To disable NB-Pstate, the system wouldn't auto restart on EVT board when idling.
BUG=b:116082728
Change-Id: Iec4f0355cb6eb1c2b0372e3d131cc5e6ba36635e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The following was tested:
- CPUs with 800, 1067, 1333MHz FSB (1333MHz FSB needs a jumper set)
- The VGA output with libgfxinit
- USB
- COM1
- Ethernet
- SATA
- PCIe
- PCI
Has the following problems:
- The Ethernet NIC is not usable after S3 resume and requires Linux to reload
the driver. Vendor firmware also has this problem so it is quite likely it
is just a atl1c driver problem.
TODO: Add documentation
Change-Id: Ibce9ecdc0e44db3703401f116c9a8bff5b66437f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Eliminate the references to PspBaseLib.c and PspBaseLib.h in
agesa_headers.h. Fix psp.c references to definitions in those files
by adding them to include/amdblocks/psp.h.
BUG=b:78514564
TEST=Build and boot grunt/ChromeOS and restore an image from the internet.
Change-Id: I2740ceb945736c6e413f7d0bd0c41a19e19c7d5a
Signed-off-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27619
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to set eMMC tuning params from the device tree so that it
can be configured per board.
BUG=b:112718426,b:112690628
BRANCH=none
TEST=Build nocturne image and checked values passed in dev tree is set
by FSP.
Change-Id: Ic71934dce9a1c380a057e579ca3fda41983b9385
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/28274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This commit creates an ampton variant for Octopus. The initial settings
are copied from Bip, but the following changes are made to support
hardware differences:
* GPIO_66 is not connected (LTE).
* GPIO_67 is not connected (LTE).
* Updated comment for GPIO_134 (EC_AP_INT_ODL), but not configured yet.
* GPIO_143 is not connected.
* GPIO_144, GPIO_145 mapped to PEN_EJECT are not connected.
* EN_PP3300_TOUCHSCREEN moved from GPIO_213 to GPIO_146.
* GPIO_213 is not connected.
* GPIO_214 is not connected.
BUG=b:111498206
TEST=None
Change-Id: I7d6cf19c906df19115b1101e3d91c62f5f3f61e3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add new mainboard variant of whiskey lake rvp, which is primary
validation platform for whiskey lake silicon, support socket DDR4 memory
module.
BUG=N/A
TEST=Build and flash, confirm boot up into kernel on whiskey lake rvp
platform.
Change-Id: I4a5e8a9ec76d5e55e55ef9bf968825c17fbe9816
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch sets the MRC UPD "CmdTriStateDis" to disable TriState for
the rammus boards. Rammus is LPDDR3 design without RTT for CMD/CTRL.
BUG=none
TEST=Run memtester app and also webgl fishtank on the LPDDR3 kabylake
boards and also check the margin data is proper in FSP.
Change-Id: Iee115f49ba5b36dc5b0425e9da02b58cd19b2236
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28568
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's only DDR4 or LPDDR3 support for coffelake processor line,
details can be found out on EDS #570805.
BUG=N/A
TEST=N/A
Change-Id: I8ba6b6861b15b40b01237f87c8d55394f7fd6706
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
No support for SoC D-1 stepping is available.
According to Intel doc #332095-015 stepping C-0 has revision
id 0x21 and D-1 revision ID 0x35.
Also correct the RID_C_STEPPING_START value for C-0.
BUG=none
TEST=Built, Intel Cherry Hill Rev F.
Change-Id: I29268f797f68aa4e3b6203e098485e0bd4a44fc4
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27471
Reviewed-by: Wim Vervoorn
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Arthur Heymans