Add a function domain_acpi_name to return "PCI0", rather than
falling back to the parent' device's "\_SB" label. This repair is
required for the LPC TPM device to register its presence without
blowing up the table and preventing the payload from finding SATA.
Before change, the TPM device reported as:
\_SB.\_SB.LPC0.TPM
After change, the TPM device reports as:
\_SB.PCI0.LPC0.TPM
A separate change submission will correct "LPC0" as well.
Change-Id: I5e8d4715c9b42f50c84dd65818e4b0fdfc9d54f9
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/26204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
I'm increasing the max because when AGESA tracing is enabled it will use
over 120 entries. I added some padding to the number incase more probes
are added. This only affects ramstage so the extra ram shouldn't matter.
BUG=b:64549506
TEST=boot on grunt and ran cbmem -t
Change-Id: I7a3d2d09c91c9e302d139e7f65fa9c85c4594de4
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This will allow loading of programs that are more than one type,
e.g. ramstage type might now be a stage or payload.
Further, unknown types of 0 are dangerous, make it a real value.
Change-Id: Ieb4eeb7c5934bddd9046ece8326342db0d76363c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/26242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Had 0x2e hardcoded, which is often the SuperIO chip. Instead,
pull the port from the PNP tree generated from devicetree.cb,
where either 0x4e or 0x2e will be specified.
Change-Id: I4a92693f8acd3a1618cefcdf6b25eb22a727e20f
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/26203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
If the timestamp entries are added out of order, the duration
calculation will be wrong.
AGESA collects timestamp data through all the stages. Then in AmdInitPost
it asks for a buffer to write TP_Perf_STRUCT into. agesawrapper will then
take the data and call timestamp_add on each entry. This results in
the entries being out of order.
TEST=Built firmware for grunt that manually added entries and then ran
cbmem -t/-T to verify the entries were in the correct order.
Change-Id: I6946a844b71d714141b3372e4c43807cfe3528ad
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26168
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is based on the code from the 8470p port. Tested on the quad
core/quad SODIMM version. This laptop uses discrete MXM 3.0b graphics
cards. Tested working with both Quadro K3000M and GTX 980M 8GB. The
laptop must be completely disassembled down to the motherboard to
perform the initial flash, subsequent flashes can be done internally
via flashrom. There is a simple mod that can be performed to make
subsequent external flashes easier in case of a brick, I'll put more
information on this on the wiki later. The lack of an MXM structure
built in to the firmware causes the GPU to enter a mode with nerfed
performance, there is a workaround though, I'll add this to the wiki
as well. I have no info on EHCI debugging.
Tested and working:
- memory: 4G+4G, 4G+4G+4G+4G
- Linux (Debian Stretch with kernel 4.9.0) booted from SeaBIOS payload
with graphics init disabled in coreboot. I allowed SeaBIOS to load the
VBIOS from the MXM.
- WLAN
- keyboard, trackpoint and touchpad
- USB
- serial port on dock
- fan control
- VGA
- DisplayPort
- Audio
- Both HDD SATA ports, ODD SATA, eSATA
- S3 with SeaBIOS 1.11, SERCON must be disabled
- Brightness and volume FN keys
- Mute and calculator hotkeys
- Status LEDs
- Bluetooth
Not working:
- GRUB2 as payload will freeze. Has something to do with at_keyboard
module. The built in keyboard requires this module to function though.
- Sleep FN key
- WiFi toggle and internet browser hotkeys
- S3 fails to resume (restarts) if the laptop is removed from AC power,
or gets unplugged and then plugged back in while suspended. Sleep
status LEDs remain normal during this process.
Change-Id: Ic4ff64e9cf0c7a51ac48ca2fe6fe8beab02e9f9a
Signed-off-by: Robert Reeves <xiinc37@gmail.com>
Reviewed-on: https://review.coreboot.org/23651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The VIA CPUs allow setting the CPUID vendor, which is best read as
a character string.
Change-Id: I67f77ca75f7d77e47b3ba09bad904df5805e373a
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
VIA c3 & C7 use the the family of 0x6 and model 10, but are not quite
Pentium III.
Change-Id: I85e9853b42cfd20db46db0bd244620d6813bc826
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18256
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copies the common/env_ctrl support code from the it8728f driver.
Tested on an ASUS AM1I-A using Linux 4.16.7-gentoo as payload,
and booting userspace without a kexec call.
Prior to this change, an error was given during boot:
it87 it87.656: Detected broken BIOS defaults, disabling PWM interface
After this change, the message is gone, and PWM fan control works
through the /sys/class/hwmon interface.
Change-Id: Id97c4ec19562e7c78308c5afe6ff7c938922c9e7
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/26224
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 0ff9daac45.
It points to a stale commit under review; i.e. not to a commit on
blob.git's master branch like it's supposed to.
Change-Id: I19cb8a32b3971c3104e381673ca08ae4d3979128
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This change adds board-specific implementation of
mainboard_vbt_filename which returns "vbt.bin" by default. This is in
preparation to allow multiple vbt binaries to be added to single
image. More sku_id specific names will be added in follow-up CLs.
BUG=b:79396300
Change-Id: I3821d55bfbe9e5773bd2eb0b0003045a80158d8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
My bad, it seems the acronym for Broadwell is BDW, and not BDL, so
I'm renaming librem_bdl into librem_bdw and changing the KConfig
options accordingly.
Change-Id: I8e992aa3474863236adf8893fcbe37c1b801fa25
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/26237
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In 4a3956d7 (drivers/intel/gma, soc/intel/common: improve
cooperation) the vbt_size parameter was not honored leading to
the use of unitialized variables from the caller. Instead, keep
track of if the vbt is already loaded by using the size returned
from the load. If it's non-zero the vbt has been loaded.
BUG=b:79562868
Change-Id: Ia1c47f0d982fae74e0223922f83943c68a846aa9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/26236
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms
BUG=b:78541692
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I5f9103aca7871095a828a74cd6a97e1951adb81f
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/26214
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without it the PS/2 keyboard doesn't work after booting into the OS.
Change-Id: Idcb0ea0779fcd5dfd6e0fbf33a532ecf0caec420
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/26131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Adding new librem_bdl variant for the Librem 15 v2, which is very similar
to Librem 13 v1, with the following differences:
- SATA ports 0 and 1 instead of 0 and 3
- SATA DTLE IOBP value is 7 instead of 9 for port 0
- There is no LAN device
- There are two SODIMM slots, and DQs are interleaved
- USB ports are different
Change-Id: Ifaca382a540d085e6c919daa992a0fbd52643a5b
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/26184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Convert the purism/librem13v1 to a variant setup, in
preparation for adding the librem15v2 board as a new variant.
The Librem 13 v1 and Librem 15 v2 are nearly identical, so
this minimizes new code to add support for the latter.
Also update the URL in board_info to an archive.org link.
Change-Id: I00bb82b9e895e2464ddaa92915c01ce0e35933a2
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/26183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I69c8b95ff1937c0b08147d9e26a3118c58129cf5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This commit adds support for writing ACPI _PLD structures that
describe the physical location of a device to the OS.
This can be used by any device with a physical connector, but is
required when defining USB ports for the OS.
A simple function is provided that generates a generic _PLD
structure for USB ports based on the USB port type.
Change-Id: Ic9cf1fd158eca80ead21b4725b37ab3c36b000f3
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/26171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This commit adds support for writing ACPI _UPC structures that
help describe USB ports for the OS.
This is a simple structure format which indicates what type of
port it is and whether it is connectable. It should be paired
with an ACPI _PLD structure to define USB ports for the OS.
Change-Id: Ide3768f60f96e9ad7f919ad3fb11d91045dc174a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/26170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This commit adds support for describing USB ports in devicetree.cb.
It allows a USB port location to be described in the tree with
configuration information, and ACPI code to be generated that
provides this information to the OS.
A new scan_usb_bus() is added that will scan bridges for devices so
a tree of ports and hubs can be created.
The device address is computed with a 'port type' and a 'port id'
which is flexible for SOC to handle depending on their specific USB
setup and allows USB2 and USB3 ports to be described separately.
For example a board may have devices on two ports, one with a USB2
device and one with a USB3 device, both of which are connected to an
xHCI controller with a root hub:
xHCI
|
RootHub
| |
USB2[0] USB3[2]
device pci 14.0 on
chip drivers/usb/acpi
register "name" = ""Root Hub""
device usb 0.0 on
chip drivers/usb/acpi
register "name" = ""USB 2.0 Port 0""
device usb 2.0 on end
end
chip drivers/usb/acpi
register "name" = ""USB 3.0 Port 2""
device usb 3.2 on end
end
end
end
end
Change-Id: I64e6eba503cdab49be393465b535e139a8c90ef4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/26169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
* This feature embedds RST into markdown for
table generation.
For more information, see
http://recommonmark.readthedocs.io/en/latest/index.html#autostructify
Change-Id: Iefebb3b7857bc98818e345f7d0e95fbf987305a8
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/26190
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds a new SPD entry for samsung's new 4GB memory and updates
atlas to use it instead of the previous gen memory.
BUG=b:79444337
TEST=booted on atlas
Change-Id: I19567736c45a1321586378c3d964c2cbebe24755
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/26185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This keeps Audio clock and data pins ON in S0ix to support
Wake on Voice.
BUG=b:77605180
BRANCH=none
TEST=Checked that S0ix suspend/resume works. Validation of WoV
was done on glkrvp previously. For Yorp, audio topology firmware
updates are required for testing WoV.
Change-Id: Idafe4e7d24fe16f8e8ff3dd86e299776ea860d03
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/26202
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This moves the blobs submodule marker forward to include the following:
b45abbd cpu/intel: microcode: add license agreement
1d37962 cpu/intel: add microcode updates 20180312 for new CPU models
8b8bbce cpu/intel: apply microcode updates 20180312 to currently tracked models
in short: bump Intel's microcode updates to the latest version. This
includes Spectre/Meltdown mitigations.
Change-Id: I4ab74ae0bdcf2a109b0697ad233fbb812b5c4544
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/25505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Was never used for the boards in our tree.
Change-Id: Ib9e9ab25ccb8d1d556fdeb8bb4c6558f25bb81b6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The patch series ending in 64049be (lib/bootmem: Add method to walk OS
POV memory tables) expanded the bootmem framework to also keep track of
memory regions that are only relevant while coreboot is still executing,
such as the ramstage code and data. Mixing this into the exsting bootmem
ranges has already caused an issue on CONFIG_RELOCATEABLE_RAMSTAGE
boards, because the ramstage code in CBMEM is marked as BM_RAMSTAGE
which ends up getting translated back to LB_RAM in the OS tables. This
was fixed in 1ecec5f (lib/bootmem: ensure ramstage memory isn't given to
OS) for this specific case, but unfortunately Arm boards can have a
similar problem where their stack space is sometimes located in an SRAM
region that should not be made available as RAM to the OS.
Since both the resources made available to the OS and the regions
reserved for coreboot can be different for each platform, we should find
a generic solution to this rather than trying to deal with each issue
individually. This patch solves the problem by keeping the OS point of
view and the coreboot-specific ranges separate from the start, rather
than cloning it out later. Ranges only relevant to the coreboot view
will never touch the OS-specific layout, to avoid the problem of losing
information about the original memory type of the underlying region that
needs to be restored for the OS view. This both supersedes the
RELOCATABLE_RAMSTAGE fix and resolves the problems on Arm boards.
Change-Id: I7bb018456b58ad9b0cfb0b8da8c26b791b487fbb
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/26182
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to ACPI 6.1 spec 19.6.44, External informs compiler that
object is external to this TABLE, no necessary for object in same DSDT
tables.
A name cannot be defined and declared external in the same table (GPID)
A name cannot be defined and declared external in the same table (CTOK)
Change-Id: Ica80b59ad6a8af865bf1551ac4e014ec5f4e7d08
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26122
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates the below:
1)
Nocturne board has only Max98373 speaker amp.
Update both NHLT and DT entries to include only Max98373
and not include DA7219.
2) I2S2 is used for Boot Beep.
So, update GPP_F0 ~ F2 pins accordingly.
3) Include DMIC-4ch configuration.
BUG=b:79362472
TEST=None [Waiting for HW to verify]
Change-Id: I0e9b3a564c22de6e84e96e5e937a3aca4ae73d75
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the Video Bios Table to improve user experience when running
coreboot's blob free graphics init.
As it's not a binary blob it should not be added to the blobs repo.
This is taken from vendor BIOS and contains purely documented
configuration data, so it should not be subjected to copyright.
Extracted using intelvbttool with applied patch
I8cbde042c7f5632f36648419becd23e248ba6f76 "util/intelvbttool: Rewrite tool"
Change-Id: I15573ddd37ee9738df1f7178f967131687a50f48
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/25926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of both featuring their own VBT loaders, use a single one.
It's the compression-enabled one from soc/intel/common, but moved to
drivers/intel/gma.
The rationale (besides making all the Kconfig fluff easier) is that
drivers/intel/gma is used in some capacity on all platforms that load a
VBT, while soc/intel/common's VBT code is for use with FSP.
BUG=b:79365806
TEST=GOOGLE_FALCO and GOOGLE_CHELL both build, exercising both affected
code paths.
Change-Id: I8d149c8b480e457a4f3e947f46d49ab45c65ccdc
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/26039
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Incorrect interrupt routing configuration prevented handling
interrupts for devices behind PCIe bridges 00:02.1 and 00:02.5.
With the new configuration, devices work as expected.
Tested with Linux 4.10 booted with the "pci=nomsi" parameter.
Change-Id: I3c95be7ba6207697afc7983d4b5f9d9a28584723
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I6efd1675b1124b200b5ff16fdef91c10b77b69d1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I7f1276ee593928956913eaeecd62fd3018cc9ae2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I4b2b8593c98791dac7a5c016e75d2c05bcfbf890
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I15f160c1e30496461f7100e3bd3a2e2467c64c4a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I6cb8f36dea4a22fdf05c57bb3e3dcaeb2da8020f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I8fe817bb514c69a647c2208a0573a2c5fe98722d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I6fc056acb8ff16a943352342b99a9ede6558d438
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I01270248bddf07df4c959f0c632e722728d0cd03
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
TEST=build
Change-Id: Icf934caf8b4584ef2633054a5cc7f5be7cc734ee
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Kevin Cody-Little