Because cpu/intel/car/romstage.c assumes a 8KiB stack size
when setting up stack guards, and all Slot 1 compatible
CPUs have enough L1 cache available for the increase.
Adjust DCACHE_RAM_BASE to match.
Boot tested on asus/p2b-ls and asus/p3b-f using a 1400MHz
Tualeron. The latter actually requires this patch to boot
successfully.
Change-Id: I5b440e7be4f3149378db88872872012c92049c20
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Make all CAR-related calculations refer to CONFIG_DCACHE_RAM_BASE
and CONFIG_DCACHE_RAM_SIZE for consistency.
Do not set %ebp before and switch directly to stack returned by
romstage_main().
Remove an unneeded 4-byte gap in CAR stack.
The caching strategy for flash XIP area should be WRPROT.
Clarify the various comments in the file on the logic.
Together they lay the groundwork for bringing EARLY_CBMEM_INIT to
intel/slot_1 boards.
Change-Id: Ibb6cf6a2adbe3a1f28bf2903d852ddc19e09b484
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21503
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove CAR testing code currently blocked out by #if. Newer CAR code
don't even do it anymore.
Change-Id: I2d53b4e7a244824c7aa2c0f597ed91e17f6cc668
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21502
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove Hyperthreading related code that was missing setup of SIPI
vector and did not work.
Change-Id: I27e329a7b667ce4405fe07a637edbc6b5be22f2d
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21375
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add support for detecting WWAN.
* Allows to turn off power to WWAN if no card is installed.
Add the following devicetree values:
* has_wwan_detection
Set to one to indicate that the following register are sane.
* wwan_gpio_num
SB GPIO num to read.
* wwan_gpio_lvl
SB GPIO level for card to be present (usually zero).
Don't enable WWAN power if no card is detected.
As there are no devicetree values yet, the new code doesn't have any effect.
Change-Id: Ie53275b384c85df8adf71fe79b3d54211c868756
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Add support for BDC detection, based on the schematics for each board.
Support for boards without schematics needs further testing.
Needs test on all boards.
Change-Id: If33ef88fb808f36b050393fa83eb1b541ce936b9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Move rtc init code into common area and update the implementation for
apollolake to avoid build break.
Change-Id: I702ce0efba25cb6fde33cc15698ae44312742367
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The RO_VPD region is required for ChromeOS.
BUG=b:65408869
TEST=Build and check coreboot.rom with fmap_decode.
Change-Id: I9c475acc5e34a3a41f815990fb1f363963c7b9b9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The original purpose of adjust_cpu_apic_entry() was to set
up an APIC map. That map was effectively only used for mapping
*default* APIC id to CPU number in the SMM handler. The normal
AP startup path didn't need this mapping because it was whoever
won the race got the next cpu number. Instead of statically
calculating (and wrong) just initialize the default APIC id
map when the APs come online. Once the APs are online the SMM
handler is loaded and the mapping is utilized.
Change-Id: Idff3b8cfc17aef0729d3193b4499116a013b7930
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
With AMD_INIT_ENV and AMD_INIT_S3LATERESTORE moved
from romstage to ramstage, heapamanager in romstage
is no longer needed.
Change-Id: Iea8ad3ddb245c83dd290436ac9d4ecac9350b88c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CONFIG_MAINBOARD_VENDOR is customizable by OEM for Chrome OS
devices. However, VBOOT_FWID_MODEL indicates the firmware vendor and
hence if CHROMEOS is selected, then VBOOT_FWID_MODEL should always
prefix "Google_" instead of CONFIG_MAINBOARD_VENDOR.
BUG=b:65493192
Change-Id: I0a2280bfd6d535586bc14d9a3c4a8198287f08bc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
- Get rid of CONFIG_ prefix from variables that don't come from Kconfig.
- Remove 2nd set of variables that are duplicates of the first set.
- Delete duplicate set of Prerequisites
Change-Id: I194b4c790b3e35353d480d34b60507a00f10ef11
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21451
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- The SMU firmware used to be named *.sbin, now is named *.csbin.
Update the makefile so that the files can be named as they are
delivered and don't have to be renamed.
- Add a Kconfig option to allow the secure os binaries to be excluded.
BUG=b:64932297
TEST=Build with old and new firmware, verify file sizes.
Change-Id: I3091f8af126159488c3c398a6dc881fa05039cff
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Adapted from Chromium commit 9756af8.
Add SOC helper to identify BSW SoC stepping. Will be used to
override USB2 phy setting based on stepping in subsequent commit.
Original-Change-Id: Ic736dd945f01cf9f24af4ce3bd3f2757abfdeb2e
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Ib2371f85ea84df4b417e25ec8840d317cd918d5f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With FSP 1.1, all FSP blobs are forward-compatible with newer FSP 1.1
header files, so adjust the header revision check to ensure that the
FSP blob isn't newer than the header, rather than an exact version match.
This resolves a version mismatch issue with Braswell ChromeOS devices,
which ship with FSP blobs newer than the publicly-released blob (1.1.2.0),
but older than the current Braswell FSP 1.1 header (1.1.7.0).
TEST: build/boot google/cyan and edgar boards, observe no adverse
effects from using current FSP header (1.1.7.0) with the factory-
shipped FSP blobs (1.1.4.0/1.1.4.2).
Change-Id: I8934675a2deed260886a83fa34512904c40af8e1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the common acpi code.ACPI code is very similar
accross different intel chipsets.This patch is an effort to
move those code in common place so that it can be shared accross
different intel platforms instead of duplicating for each platform.
We are removing the common acpi files in src/soc/intel/common.
This removes the acpi.c file which was previously in
src/soc/common/acpi. The config for common acpi is
SOC_INTEL_COMMON_BLOCK_ACPI which can be defined in SOC's
Kconfig file in order to use the common ACPI code. This patch also
includes the changes in APL platform to use the common ACPI block.
TEST= Tested the patch as below:
1.Builds and system boots up with the patch.
2.Check all the ACPI tables are present in
/sys/firmware/acpi/tables
3.Check SCI's are properly working as we are
modifying the function to override madt.
4.Extract acpi tables like DSDT,APIC, FACP, FACS
and decompile the by iasl and compare with good
known tables.
5.Execute the extracted tables in aciexec to check
acpi methods are working properly.
Change-Id: Ib6eb6fd5366e6e28fd81bc22d050b0efa05a2e5d
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/20630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
APL internal UARTs are not used on this mainboard.
Change-Id: I39118262fc6f37b45785538a3f2d1d31d42cbe86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is one on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I45202937eba11da3bea14fef6ebed70599804335
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Boards with CBMEM_TOP_BACKUP=y can also use POSTCAR_STAGE
for MTRR setup after adding this file in the build.
Change-Id: I5f9a673ff59ccfbba16308d27f653f5cf3b49017
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Postcar failed when loading from stage_cache, if
romstage did not pass same pcf->stack on normal
and resume paths.
Change-Id: I853afb1fbdb942fd671d89950911c850c96e3af3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The change allows to update rmodule parameters after
it has been loaded from stage cache.
Change-Id: Ib825ffe245d447ad3a8246f7dbd52c6e34103a0c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements soc function to get previous sleep state
using chipset_power_state global structure.
acpi_get_sleep_type is needed in PRE_RAM stage when soc selects
CONFIG_EARLY_EBDA_INIT kconfig option.
Change-Id: I79acbfc09c8d255fbf9d73e49e8c7764f3f3fac6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Fix the warnings of klocwork scan.
e.g. "Pointer 'dev' checked for NULL at line 158 will be dereferenced at line 159"
Change-Id: I6cc9c68652b074c666c86456183460ca38a886ed
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We've decided to move control for the 3.0V rail (technically 3.3V on
Scarlet, but who cares about millivolts) back to a GPIO on the AP for
Scarlet rev2. This patch adds the necessary code to enable it and make
ARM TF aware of its existence. Since the pin had previously not been
connected to anything, we shouldn't really need to guard this by board
ID... older Scarlets will just be twiddling an empty pin.
Change-Id: I6037aa486b50119f2c7b859b966cadc3686e3459
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/21328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Vendorcode expects some DRAM controller registers to
be writable, but they are actually locked after soft
resets if C6 states are enabled.
Without the workaround, raminit fails on soft resets.
Change-Id: I6b9e275e11b2907d026c13341334983a4d9c8889
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's too critical to ignore when sending the message on
SMBus fails, so allow for a fair amount of retries.
Failure here causes watchdog to do hard reset later.
Move it out of mainboard.c as we need to call this
early in romstage while we are debugging.
Change-Id: I1006b079269d6dd44de630db7a5694124af2f974
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix regression caused by commit
9e94dbf ACPI: Get S3 resume state from romstage_handoff
Boards with EARLY_CBMEM_INIT are required to provide
romstage_handoff structure to signal S3 resume path.
Change-Id: I7c9065ccc48dfbdefade698ed275756f17dff7a0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix regression caused by commit
9e94dbf ACPI: Get S3 resume state from romstage_handoff
Boards with EARLY_CBMEM_INIT are required to provide
romstage_handoff structure to signal S3 resume path.
Change-Id: I464feb1655a51a937b6cf53508dd5c7aa0d8f791
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Fix regression caused by commit:
714709f AMD fam10 ACPI: Use common fixed sleepstates.asl
Adding common sleepstates.asl got lost in rebase process.
Change-Id: I4f22ee950ae5637113db8e79ca238cb1b81002aa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds imon and vmon slot numbers for Maxim 98927 driver.
These values are used to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I4382da4f984507d147751c168e8177b58c88a70f
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change list adds imon and vmon slot numbers as params for
Maxim 98927 driver. These values are looked up in the kernel driver
to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I21d72ba91af83782587f11018b2d1d1c8d4f676c
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There was already a uart.c added to bootblock. Remove the
duplicate addition.
Change-Id: I2d420ff7437d25a596ee9a120964f8d4bc413bc4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add Vboot and ChromeOS support in SOC Kconfig, include a separated
verstage in Makefiles.inc as well.
Change-Id: I114a9d6e92b69199ccacc1e7e1535eccc0e2cb99
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kyösti Mälkki