For devices sharing same firmware, there may be few customization based
on SKU ID - for example being clamshell or form factor. On Kukui and
Jacuzzi platforms the SKU ID is defined on AP SOC, so we have to send
the information to EC.
BUG=b:161767717
TEST=make -j # builds and boots on Juniper
BRANCH=kukui
Change-Id: I8ffdd9fd1e609c1dd4b0e22dc7aab560ccdc842e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43788
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, audio is not working on Boten, caused by the coreboot
HDA driver not being run as the Jasper Lake PCI ID is missing.
So, add the Jasper Lake ID.
BUG=b:160651126
BRANCH=NONE
TEST=Connect speaker to audio jack, and verify sound is played.
Signed-off-by: Yan Liu <yan.liu@bitland.corp-partner.google.com>
Change-Id: Ib62c332d8d87201b3e6903251d824e1c3e06cd68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43441
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Peichao Li <peichao.wang@bitland.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
HDMI DDC GPIOs were configured as NC till now in waddledoo.
This may cause HDMI i2c transfer to break and EDID read will
fail due to wrong configuration
Configuring these GPIOs as NF in coreboot to fix the issue.
BUG=b:160324327
BRANCH=None
TEST=HDMI works on DDI2 onn Type-C port
Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C bus3 frequency and insure it meets I2C spec.
BUG=b:161650117
TEST=flash coreboot to the DUT and actual measured I2C bus3
make sure it meet Spec.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Ifa9f0bce723f55a12fd2313788c995f8326e3e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the scan-build warning below:
CC romstage/drivers/mrc_cache/mrc_cache.o
src/drivers/mrc_cache/mrc_cache.c:450:26: warning: Value stored to 'flash' during its initialization is never read
const struct spi_flash *flash = boot_device_spi_flash();
^~~~~ ~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
The function can return early before the value is read. Fix this, by
getting rid of the variable, as the value is only read once.
Change-Id: I3c94b123f4994eed9d7568b63971fd5b1d94bc09
Found-by: scan-build (clang-tools-9 1:9.0.1-12)
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Rename the pch_init function to bootblock_pch_init and romstage_pch_init
according to the stage it is defined in.
TEST=Able to build and boot Waddledoo successfully.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: Iaa0a41f3b5972251d6cd9359bbb46d392196b2e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The outb() call is replaced with the post_code()
The post_codes.h is replaced with console.h since console.h
includes both the post_code definition and post_codes.h
Change-Id: I21345260e86de30614c416e2f509bd77b9e00cb7
Signed-off-by: Sindhoor Tilak <sindhoor@sin9yt.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
BOOL type Kconfig values should be used through the CONFIG() macro.
These instances were not, so update them.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie4706d82c12c487607bbf5ad8059922e0e586858
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We have definitions for the bits in the PCI COMMAND register. Use them.
Also add spaces around bitwise operators, to comply with the code style.
Change-Id: Icc9c06597b340fc63fa583dd935e42e61ad9fbe5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Mark the CPU as enabled and the socket as populated.
EDK2 tests these flags before further reading this structure.
Change-Id: Ic545bb47c502cb9d2352ba6d43eaed8c97229c02
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43703
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement type 19 by accumulating the DRAM dimm size found in cbmem's
CBMEM_ID_MEMINFO structure. This seems common on x86 where the
address space always starts at 0.
At least EDK2 uses this table in the UI and shows 0 MB DRAM if not
present.
Change-Id: Idee8b8cd0b155e14d62d4c12893ff01878ef3f1c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Don't initialize fields with zeroes since gnvs structs were zeroed out
in southbridge already. Also add some comments.
See also these commits:
* Commit a76cf28 with Change-Id
I2ccf4699ba3ed3f5b9402c0340153d4a5bf82682 ("mb/lenovo/*/acpi_tables:
Don't initialize already initialized fields").
* Commit 0c52638 with Change-Id
I71f092ed7582b4931122d72f41d0b42a7569b96e ("mb/lenovo: Remove
thermal.h header").
Change-Id: I1a0042bc93a2b30babcb896b3df23faf37998f3c
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40479
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Update MAINBOARD_PART_NUMBER for TGL variants
- MAINBOARD_PART_NUMBER is reported as FRID on acpi
- This is required for cros_config to differentiate
across TGL variants.
- Mosys uses cros_config to identify TGL variants using
data read from FRID
Bug=none
Test=build and boot coreboot on TGLRVP UP3 hardware
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Set up a 8-byte I/O range at 0x290-0x297 as PIIX4's generic device 9,
which activates a chip select when this range is accessed.
On the P2B family it connects to the W83781D hardware monitor,
allowing access to it over the ISA bus, just like vendor firmware.
Apparently this does not work on p3b-f, but no ill effects observed
either.
TEST=On p2b-ls lm-sensors can detect chip and get readings over ISA.
Change-Id: Iaed1df7230359e94c580c305f4769c8bb4f5fce0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These will be put to use in a follow-up.
Change-Id: Id13dde5ce2239064b9b18de7ca516525158ae268
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove EIO define. It is unused and means something else,
elsewhere in the tree.
Move PMIOSE bit definition next to PMREGMISC, where it actually
belongs.
Correct a number of bit defines with glaring errors.
Clarify in comments which PM register defines are in PCI config
space are which are in I/O space.
Change-Id: Ic7f2267d013403c0a519c2ee1786bd3c7f5a9708
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Embedded Firmware Structure contains various SPI parameters for
the PSP to program. This change adds support to amdfwtool for
populating these values as well specifying SOC Family and Model.
BUG=b:158755102
TEST=Read EFS values at appropriate offsets using a hex editor. Boot
test on Tremblye and Morphius.
Change-Id: I87c4d44183ca65a5570de5e0c7f9b44aa6dd82f9
Signed-off-by: Matt Papageorge <matt.papageorge@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42566
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Coverity detects dereferencing pointers that might be "NULL" when
calling acpigen_write_scope and acpigen_write_device. Add sanity
check for both of scope and name to prevent NULL pointer dereference.
Found-by: Coverity CID 1430454
TEST=Built and boot up to kernel on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I8ece3831bbd2641ceafbd71b9dc3db7e04a8eae4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43449
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously, the spi base address code was using a number of different
functions in a way that didn't work for use on the PSP.
This patch consolidates all of that to a single saved value that gets
the LPC SPI base address by default on X86, and allows the PSP to set
it to a different value.
BUG=b:159811539
TEST=Build with following patch to set the SPI speed in psp_verstage.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I50d9de269bcb88fbf510056a6216e22a050cae6b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43307
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The while loop in \_SB.DPTF._OSC accidentally used <= instead of <, so
there was an error indexing into IDSP.
BUG=b:162043345
TEST=verify disassembled ASL, as well as no BIOS bug mentioned in
/var/log/messages
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I08c4152c59cc9eb13386c825aab983681cfa88ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
I accidentally had the same value for two different postcode
entries. Fix that.
BUG=None
TEST=Watch postcodes in psp_verstage
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id0bf18efc7e79278a21683c11a1084d2a7d97e6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The only reason to use a named choice statement is if you plan on
having the choice statement in multiple places. Since none of these
are used in multiple places, we can get rid of the names.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie5f84e9dc38050234976bd193ac5fbf649e564f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Missed one other scope operator in the DPTF cleanup. This one is for the
fan device, and without this fix, the kernel isn't able to properly
control the fan (it gets confused about whether it's ACPI 4+ compatible
or not).
BUG=b:149722146
TEST=verify /sys/class/thermal/cooling_zone0/max_state returns > 1,
and /sys/class/thermal/cooling_zone0/cur_state is writable, and writing
the value of `max_state` causes the fan to spin faster.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7bd83967ace761ddd17eaeae9c25abb0b2cbe413
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Variants that select BASE_ASUS_P2B_D will also get
MAX_CPUS==2 below, so this was redundant.
Change-Id: I9048a4821f19d90e1489b09e294d2551941abf10
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43809
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's not stricly related to spinlocks. If defined, a better
location should be found and the name collisions with other
barrier() defined in nb/intel solved.
Change-Id: Iae187b5bcc249c2a4bc7bee80d37e34c13d9e63d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43810
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's not related to spinlocks and the actual implementation
was also guarded by CONFIG(SMP).
With a single call-site in x86-specific code, empty stubs
for other arch are currently not necessary.
Also drop an unused included on a nearby line.
Change-Id: I00439e9c1d10c943ab5e404f5d687d316768fa16
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43808
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's a `GPL-2.0-or-later` version of this file in volteer2, so use it
in place of these weirdly-licensed files.
Change-Id: Icde2f6539d9c726d6967350f74e7bc015e01e7b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are many places where we do this. Put it inside an inline function
for convenience reasons.
Change-Id: I5515a52458b6c78c1a723cb08e6471eb9bac9cd6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43871
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hung-Te Lin