The initial timestamps are now pushed on the stack when entering the
romstage C code.
Tested on Asus P5QC.
Change-Id: I88e972caafff5c53d8e68e85415f920c7341b92d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This removes the need to synchronize the devicetree and the romstage
writing to FD.
Change-Id: I83576599538a02d295fe00b35826f98d8c97d1cf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30244
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The newest and most useful incarnation was hiding in soc/intel/common/.
We move it into the Mainboard menu and extend it with various flags to
be selected to control the default and which options are visible. Also
add a new `int` config MAINBOARD_POWER_FAILURE_STATE that moves the
boolean to int conversion into Kconfig:
0 - S5
1 - S0
2 - previous state
This patch focuses on the Kconfig code. The C code could be unified as
well, e.g. starting with a common enum and safe wrapper around the
get_option() call.
TEST=Did what-jenkins-does with and without this commit and compared
binaries. Nothing changed for the default configurations.
Change-Id: I61259f864c8a8cfc7099cc2699059f972fa056c0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Note that while these boards had entry 0x0ff0 in comparison
to 0x0ffc of the get_default_pci1234() initialisation, the
implementation of get_pci1234() unconditionally overrides
the first entry.
Change-Id: I8bec612f84fe3c3a0c21fc1e10629368857e9c5e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
All these boards use the same default initialiser.
As this is initialized late after device enumeration,
it can't really be used to alter platform configuration.
Change-Id: I30fc0298081df0442ec4e9a527340b93a3cd6106
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Values in the array are not used anywhere.
Change-Id: Iee92f903db97533709d54d1f214f2f23a1fab06b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Values in the array are not used anywhere.
Change-Id: I608b8c2e21bc515c56a27982815c1da43f3bb976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It has to be called once before PIRQ and MP table generation.
Change-Id: I238c6b4810404d320b36d4f6b4a161c1ff11c8d3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Also remove global ramstage-y += get_bus_conf.c, this is
specific to amdfam10.
Change-Id: I49b604ebff6bcfe85518b2c3896ab798c3c7878d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Value of the global is never evaluated.
Change-Id: I74106b0f5f033053288882a5bcd3c1dba3235ac0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This mainboard has the BSEL straps hooked up to the SuperIO
similar to the ASUS P5GC-MX and might therefore require a restart.
Tested:
- FSB 800, 1067 and 1333MHz CPUs
- USB
- Ethernet
- Serial
- 2 DIMM slots
- SATA
- Libgfxinit (VGA)
TESTED with SeaBIOS (sercon disabled) and Linux 4.19.
Change-Id: Id845289081751ff8900e366592745f16d96f07c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Any board that uses the AST driver will have support for native graphics
init. So, select the option in the driver instead of every board.
Change-Id: I2bf42c168d1ffdda11857854889b74953abd7e40
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This board doesn't have a UART on the super I/O. Selecting this option
speeds up boot time from ~493 ms to ~416 ms.
Change-Id: I1d84f373831381da79022638e1082adf68f47aad
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When the BMC firmware module is installed on the KGPE-D16, the
RAM SPD multiplexer lines are disconnected by hardware from the
SP5100 GPIOs and attached to BMC GPIO lines instead.
Set the BMC GPIOs to match the state of the SP5100 GPIOs during
RAM setup.
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac5
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/19820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This makes the mainboard able to boot again.
Change-Id: Id96fbfd5c815431dba2f030fca62a5ea16b97393
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29994
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Working:
- SATA on southbridge ports
- SATA on Marvell IDE controller ports
- USB
- COM1
- PS/2 keyboard
- DDR2 DIMMs
- PCIe x16 PEG port
- PCIe x1 ports
- PCI ports
- NIC (MAC address needs to be set in Kconfig or in a CBFS file)
- S3 resume
- Green audio line out connector (the rest is untested)
Not working:
- Floppy port. Does not seem to be mainboard-specific, though.
Untested:
- EHCI debug
TODO:
- Add documentation
Change-Id: I6ed434a691e8ef2a61e0acb1f986a59b8e1ad818
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/25691
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Even though these two mainboards use the same gpio.c file, other boards
such as the p5ql_pro do not.
Change-Id: I2f7c8c12cb1bdcf47f3b4d4cef0b11e44a5b8863
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/29447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
On some boards the devicetree and Function Disable register did not
match. In this case the FD values are put in the devicetree as these
were the values that were actually used in practice.
A complete devicetree will make it easier to automatically disable
devices in ramstage.
Change-Id: I1692ca5f490ea84e2fc520d3f66044ad7514f76e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Instead of having the code for the RAM init time stamps in each
mainboard’s `romstage.c`, factor it out to the northbridge code, done in
commit 771328f7 (intel/i945: add timestamps in romstage).
Change-Id: Ibb699a1fea2f0b1f3c6564d401542d2fb3249f5a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17994
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
