Migrate the last two platforms to using Kconfig through
`get_valid_prmrr_size()` instead of hardcoded values in the devicetree.
Change-Id: I93aa177f741ca8b2a2d50fae2515606b96784e83
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that primus can successfully
boot into OS with non-serial coreboot.
BUG=b:199967106
TEST=USE="project_primus" emerge-brya coreboot and verify it builds
without error.
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I9c66efe96515347502d059556052c764c1be5d09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Including arch/cpu.h is needed to have the declaration for
cpu_get_feature_flags_ecx.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I091c82f5a55ee9aa84a255c75c7721eff989344d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Including arch/cpu.h is needed to have the declaration for cpuid_eax.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic22aba062117e3afa818fa2fc39cb0738e6a1612
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Apart from the u8, u16 and u32 types, the bool type is used in this file
so include types.h instead of stdint.h to have bool defined too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95f037deb0fe11b717586df655065bfbb33b0d23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Apart from the bool type, uint8_t, uint32_t and uint64_t are used in
this file, so include types.h instead of stdbool.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I30088d68132058f40b974fbaa822f322b58ed6c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Both bool and uintptr_t types are used in this file, so include types.h
to have the definitions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I647d9f50cd6edaf08bebf5d713cd05731fadfc1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
These statements fit on a single line. Reflow them to ease future works.
Change-Id: Ie18e9a00f67b999fdcedcab3c28b68e34bc93da4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Follow FIBOCOM_L850-GL Hardware User Manual_V1.0.8.
BUG=b:180166408,b:187691798
TEST=measure WWAN power off by scope is meeting the spec.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I6b2725cd61d5b54bc7fd70a9daffd29e7b43690b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When the century byte was reserved, the debug_level was accidentally
converted from an enum to a hidden value. Change it back to an enum.
Fixes: f05bd8830d ("mb/system76/*: cmos.layout: Reserve century byte")
Change-Id: Id88a7aed7b2fc793fd003db5b45f3f201b1a7630
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
When using a debug build of the FSP, the FSP-M binary is larger than the
memory region we have allocated for it, so increase the size to make the
binary of the debug build fit in there. Also adjust the VERSTAGE_ADDR so
that it starts right after the the FSP-M memory region.
TEST=coreboot builds now successfully when using a debug version of the
FSP
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib64806bcf948d5ed4bcf8e1f50004091f125dc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Currently there are two versions of spd_tools: one for LP4x and one for
DDR4. This change is the first step in unifying these into a single
tool.
This change implements a unified version of the spd_gen tool, by
combining the functionality currently in lp4x/gen_spd.go and
ddr4/gen_spd.go. The unified version takes the memory technology as an
argument, and generates SPD files for all platforms supporting that
technology.
BUG=b:191776301
TEST=Compare the SPDs generated by the old and new versions of the tool
for all supported platforms. For reference, the test script used is
here: https://review.coreboot.org/c/coreboot/+/57511
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I7fc036996dbafbb54e075da0c3ac2ea0886a6db2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
To save the space for FW, some of the FWs are going to be defined as
LVL2 entries. To be compatible to "flattened" layout, we still drop
the LVL2 entry to level1 if there is only one level.
Change-Id: Ibe8cdd5c14225899352b02bb19aae6059d56d428
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The `CaVrefConfig` FSP-M UPD describes how the on-die Vref generators
are connected to the DRAM. With the exception of an early Skylake RVP
board (which doesn't have coreboot support), mainboards using DDR3 or
LPDDR3 memory should set `CaVrefConfig` to 0, whereas mainboards with
DDR4 should set `CaVrefConfig` to 2. MRC uses this information during
memory training, so it is important to use the correct value to avoid
any issues, such as increased power usage, system instability or even
boot failures.
However, several Skylake DDR4 mainboards don't set `CaVrefConfig` to 2.
Although they can boot successfully, it's not optimal. For boards that
set `DIMM_SPD_SIZE` to 512 (DDR4 SPD size), set `CaVrefConfig` to 2.
Change-Id: Idab77daff311584b3e3061e9bf107c2fc1b7bdf1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Implement _BIX method to expose battery cycle count.
Requires an EC version with support for cycle count.
Change-Id: I5f7a1d275caff59960aaf9c39b9c707970350987
Signed-off-by: Ian Douglas Scott <idscott@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
vboot_reference is introducing a new field (ctx) to store the current
boot mode in crrev/c/2944250 (ctx->bootmode), which will be leveraged
in both vboot flow and elog_add_boot_reason in coreboot.
In current steps of deciding bootmode, a function vb2ex_ec_trusted
is required. This function checks gpio EC_IN_RW pin and will return
'trusted' only if EC is not in RW. Therefore, we need to implement
similar utilities in coreboot.
We will deprecate vb2ex_ec_trusted and use the flag,
VB2_CONTEXT_EC_TRUSTED, in vboot, vb2api_fw_phase1 and set that flag
in coreboot, verstage_main.
Also add a help function get_ec_is_trusted which needed to be
implemented per mainboard.
BUG=b:177196147, b:181931817
BRANCH=none
TEST=Test on trogdor if manual recovery works
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I479c8f80e45cc524ba87db4293d19b29bdfa2192
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57048
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make neovim the default editor and create an alias for vim.
The NixOS module for neovim is currently broken. Thus, add a note to
`description.md` to switch to that later.
Change-Id: I9345a6e32f3035565e55e50579c97121b4987d83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57393
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a Nix shell file which provides an environment for compilation of
the coreboot toolchain. The Nix shell can be used by running the
following command:
$ nix-shell --pure util/nixshell/toolchain.nix
The `--pure` parameter is optional, but it makes sure that the
environment is as minimal as possible and does not contain any unrelated
or unneeded software or configuration.
Once compiled, the coreboot toolchain can be used without loading the
shell environment.
If `--pure` is used, SSL connections won't work since the
`SSL_CERT_FILE` environment variable is not configured, which makes the
build tool unable to download the source files. Thus, let it point to
the system certificate store.
Change-Id: I341ee28c5451d2c6cb4ff22de67161d99f4ca77a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This now skips all of the pieces done by PSP_verstage.
BUG=None
TEST=Boot Guybrush with & without PSP_verstage
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5a6b8e2284e232c30c9f36ea7c6ab044e2644f7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Since the PCIE training for the USB WWAN card is no longer being run,
we can initialize the GPIOs the same for all WWAN cards.
BUG=b:193036827
TEST=Boot and reboot with fibocom FM350-GL & L850GL modules
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idc9a7cb883fc8dd6bbc6077b8ea99182f17f888b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57317
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check to see if the PCIe slot needs to be activated for the WWAN card.
If it doesn't, leave it unused so it will be powered off and not do
the PCIe training.
BUG=b:193036827
TEST=Boot & Reboot guybrush with both PCIe & USB WWAN cards.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I79c32e4814672c03ee0821786d5be1c77fd1b410
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:200009010
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I09c7830fff6b318cf1a1f4a44ee0a819691f7c58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57673
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add MIPI camera support for OVTI2740
BUG=b:196937374 b:194926283
TEST=Build and boot on Kano
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I248c64b9460c898f9faa5f7ac8cf339a9c814013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch has changes to support multiple camera modules, base on the value set in the SSFC_CONFIG.
BUG=b:198235323
TEST=tested the changes with redrix 5MP(ov5675/hi556) camera.
Change-Id: I71c8355617171ec7d08862759b87d4bf12ce2924
Signed-off-by: Arec Kao <arec.kao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57272
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCIe WWAN module used on brya0 requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WLAN_RST#, then WLAN_PERST# in ramstage
BUG=b:187691798
Change-Id: I10f15a4dcfd86216c334fb24b4693ea250d35ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This GPIO is used to force the USB retimers on Type-C ports to stay in a
powered state and can be used e.g., during a firmware update to the
retimer to force power on even when no device may be connected to the
port. However, its power rail is controlled elsewhere and coreboot is
not applying a FW update, so this GPIO should be driven low instead.
BUG=b:193402306
TEST=compile
Change-Id: I976a0b8252b31aacef476d5ee4bcf6b1ef2e79de
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Adds "add" command to elogtool. This command allows adding elog events
manually. It supports event type and, optionally, event data.
If the free buffer space is < 1/4 of the total space, it shrinks the
buffer, making sure that ~1/4 of the free space is available.
BUG=b:172210863
TEST=./elogtool add 0x17 0101
./elogtool add 0x18
Repeated the same tests on buffers that needed to be shrunk.
Change-Id: Ia6fdf4f951565f842d1bff52173811b52f617f66
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Updated return type as CB_SUCCESS and aligned indentation.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ifabe0508a37a841779965f4e38172f680e18d38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Add mipi panel support for wormdingler
- Add the following panel for wormdingler:
INX P110ZZD-DF0
BOE TV110C9M-LL0
- Use panel_id to distinguish which mipi panel to use.
- Setup panel orientation
BUG=b:195898400,b:198548221
BRANCH=none
TEST=emerge-strongbad coreboot
Change-Id: I8cd28e024ecbfdcd473bc39efb529eb4aca1b5d0
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add supported memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
2. Hynix H54G46CYRBX267
BUG=b:199032134
TEST=emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: If8b75f9ed4d789d6c9c4365c517358df8d6e55c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
touchpad:390kHz
codec:395.8kHz
BUG=b:199481261
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ifadc3d19eb57fe6f67504be154c30df7bc0fee71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
All variants originally had been changed to start with an arrow with
two spaces following it to line up with the platform name. A number
of recent platforms were added only using a single space. This change
updates them all to have two spaces so they line up again.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iab9e6207fff5a7d2f6d76e5ca33eeaca721a224f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
FspMultiPhaseSiInit API was introduced with FSP 2.2 specification
onwards. EnableMultiPhaseSiliconInit is an arch UPD also introduced
as part of FSP 2.2 specification to allow calling FspMultiPhaseSiInit
API.
However, some platforms adhere to the FSP specification but
don't have arch UPD structure, for example : JSL, TGL and Xeon-SP.
Out of these platforms, TGL supports calling of FspMultiPhaseSiInit
API and considered EnableMultiPhaseSiliconInit as a platform-specific
UPD rather than an arch UPD to allow calling into FspMultiPhaseSiInit
API.
It is important to ensure that the UPD setting and the callback for
MultiPhaseInit are kept in sync, else it could result in broken
behavior e.g. a hang is seen in FSP if EnableMultiPhaseSiliconInit
UPD is set to 1 but the FspMultiPhaseSiInit API call is skipped.
This patch provides an option for users to choose to bypass calling
into MultiPhaseSiInit API and ensures the EnableMultiPhaseSiliconInit
UPD is set to its default state as `disable` so that FSP-S don't
consider MultiPhaseSiInit API is a mandatory entry point prior to
calling other FSP API entry points.
List of changes:
1. Add `FSPS_HAS_ARCH_UPD` Kconfig for SoC to select if
`FSPS_ARCH_UPD` structure is part of `FSPS_UPD` structure.
2. Drop `soc_fsp_multi_phase_init_is_enable()` from JSL and Xeon-SP
SoCs, a SoC override to callout that SoC doesn't support calling
MultiPhase Si Init is no longer required.
3. Add `FSPS_USE_MULTI_PHASE_INIT` Kconfig for SoC to specify if
SoC users want to enable `EnableMultiPhaseSiliconInit` arch UPD (using
`fsp_fill_common_arch_params()`) and execute FspMultiPhaseSiInit() API.
4. Presently selects `FSPS_USE_MULTI_PHASE_INIT` from IA TCSS common
code.
5. Add `fsp_is_multi_phase_init_enabled()` that check applicability of
MultiPhase Si Init prior calling FspMultiPhaseSiInit() API to
honor SoC users' decision.
6. Drop `arch_silicon_init_params()` from SoC as FSP driver (FSP 2.2)
would check the applicability of MultiPhase Si Init prior calling
FspMultiPhaseSiInit() API.
Additionally, selects FSPS_HAS_ARCH_UPD for Alder Lake as Alder Lake
FSPS_UPD structure has `FSPS_ARCH_UPD` structure and drops
`arch_silicon_init_params()` from SoC
`platform_fsp_silicon_init_params_cb()`.
Skip EnableMultiPhaseSiliconInit hardcoding for Tiger Lake and uses
the fsp_is_multi_phase_init_enabled() function to override
EnableMultiPhaseSiliconInit UPD prior calling MultiPhaseSiInit FSP API.
TEST=EnableMultiPhaseSiliconInit UPD is getting set or reset based on
SoC user selects FSPS_USE_MULTI_PHASE_INIT Kconfig.
Change-Id: I019fa8364605f5061d56e2d80b20e1a91857c423
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch selects SOC_INTEL_COMMON_BLOCK_TCSS from Alder Lake SoC
Kconfig and drops SOC_INTEL_COMMON_BLOCK_TCSS Kconfig selection from
specific mainboard (brya) to ensure all Alder Lake mainboards can make
use of common TCSS block.
BUG=b:187385592
TEST=Type-C pendrive/Gen-2 SSD detected as Super speed.
Change-Id: I85f6a967eb34ea760418131a9586bfdeb13c9b5d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch allows ADL-RVP mainboards to set AUX GPIO PADs based
on the board id value.
Various ADL-P and ADL-M RVPs SKUs demand different GPIO AUX programming
hence, this patch implements a helper function inside `adlrvp` mainboard
to override devicetree chip config.
Note: Different ADL-P/M SKUs (LP4/LP5/DDR4/DDR5) don't have dedicated
devicetree for overrides hence, board id is being used for unique SKU
identification.
Additionally, skip AUX GPIO PAD filling up for Windows SKUs.
TEST=Able to override AUX GPIO PADs based on ADL-P RVP board id.
Change-Id: I2f0a37c7a8bd69af715551df2a93e6eed89e954a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This function is "extracted" from cmd_clear().
This new function will be called from cmd_add(), and new command that
will be added in a future CL (see CL chain).
Additional minor fixes:
- calls usage() if no valid commands are passed.
- Slightly improves usage() output. Needed for cmd_clear()
BUG=b:172210863
TEST=elogtool clear
Change-Id: I0d8ecc893675758d7f90845282a588d367b55567
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit 2eb100dd12 added PMC LPM requirements to the the PEP ACPI
objects, but it was not made clear that one of the pointer arguments to
the mentioned function is not supposed to be NULL and Coverity
complained. Make the intention clear by instead asserting that `info`
cannot be NULL.
Fixes: Coverity CID 1462119
Change-Id: I9e8862a100d92f4a7ed1826d3970a5110b47f4c4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change uses a static 8-bit counter in
`acpi_device_add_power_res()` to generate the name of power resource
object rather using a default name "PRIC". This makes it easier to
identify which power resource Linux kernel logs are referring to. If
more than 256 power resources are used in the system, then the counter
will wrap around to 0. However, 256 seems to be a large enough number
for the power resource count.
TEST=Verified that Power Resources are named as expected:
```
dmesg | grep ACPI | grep PR
[ 0.550921] ACPI: Power Resource [PR00] (on)
[ 0.869960] ACPI: Power Resource [PR01] (on)
[ 1.013973] ACPI: Power Resource [PR02] (on)
```
No new ACPI errors are seen in dmesg on brya.
Change-Id: Ia18f7177b03821ce0f8c989ae5d258f2f83517a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
copy existing QUP driver from /soc/qualcomm/sc7180 to common folder.
This QUP common driver provide QUP configurations, GPI and SE
firmware loading and initializations.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I95a0fcf97b3b3a6ed26e62b3084feb4a2369cdc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
SPI NOR size should match with coreboot ROM size. On QCOM Piglin board SPI
NOR size is 64MB and the default coreboot ROM size is 8MB. So, update the
coreboot ROM size to match with SPI NOR size.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board and checked
basic boot up.
Change-Id: I78f3f402b383bbad303f26c31d3d973c5f20d172
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Michael Niewöhner