This patch makes strtok_r:
- handle the end of the string
- handle string that contains only delimiters
- do not set ptr outside of str
Change-Id: I49925040d951dffb9c11425334674d8d498821f1
Signed-off-by: Jeremy Compostella <jeremy.compostella@gmail.com>
Reviewed-on: https://review.coreboot.org/16524
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Move the current devicetree.cb to be under variants/baseboard.
New variants can provide their own devicetree as needed.
BUG=chrome-os-partner:56677
Change-Id: Ib109ca4be883884b318264500d14aa8d40e3072a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16510
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The early TPM probe was done directly in tis.c ignoring the lower
layer that provides appropriate access to the chip. Move this into
a tpm_vendor_probe() function so it can use iic_tpm_read() with all
of the built-in delays and semantics instead of calling i2c_readb()
directly from the wrong layer.
This fixes early init failures that were seen with the cr50 i2c tpm
on the reef mainboard.
Change-Id: I9bb3b820d10f6e2ea24c57b90cf0edc813cdc7e0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16527
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable the hexdump function in verstage as it can be useful there for
debugging I2C and TPM transactions.
Change-Id: If9dc4bcc30964e18ff5d8a98559f6306c0adec6f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16528
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For an unknown reason the printed address in the SPI debug messages is
modified before it is printed by subtracting the constant 0xf020 from
the passed in address.
What I suppose this debug code should do is to print the used register
address within the SPI controller while any parts of this address that
belongs to the SPI base address should be omitted. To fix that remove
the subtraction of 0xf020 and adjust the address mask to 0x3ff so that
only the offset to the registers inside the SPI controller will be
visible in the debug messages.
In addition switch to uint8_t and friends over u8 to sync up with used
types in this file.
Change-Id: I93ba7119873115c7abc80a214cc30363a6930b3b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16500
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Hardcoding the microcode filenames into the makefiles is great when
the microcode is in the blobs directory. When the microcode isn't
posted to the blobs directory, we need some method of supplying the
microcode binary into the build. This can of course be done manually
after the build has completed, as can be done with everything that
we're including in the ROM image. Instead of making life hard for
everyone though, let's just add a way to specify where the microcode
rom comes from.
BUG=chrome-os-partner:53013
Change-Id: I7c5127234809e8515906efa56c04af6005eecf0b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/16386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Omar Pakker
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Defining this OpRegion for SMBus controller prevents linux kernel
driver i2c-i801 from registering SMBus under sysfs, with following
error in dmesg:
ACPI Warning: SystemIO range .. conflicts with OpRegion .. (\_SB.PCI0.SBUS.SMBI)
Solution taken from intel/bd82x6x. Worth noting we do not
define ENABLE_SMBUS_METHODS anywhere currently.
Removed remaining reference to HSTS from GETAC P470.
Change-Id: I7c13d344b0343387681b46019cc5061b1435b46b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16266
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Similarly to 2b2f465fcb
"mb/gigabyte/ga-g41m-es2l: Fix ACPI IRQ settings for SATA"
SATA must function in "plain" mode because it does not work in
"combined" mode.
Tested on d945gclf
Change-Id: I2e051a632a1341c4932cf86855006ae517dbf064
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16319
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
The script checkpatch.pl complains about these files. Fix
the warnings.
Change-Id: I4271cc35bb101447a316a75273cf8a6e95ed62d5
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/16011
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
DIV_ROUND_CLOSEST and DIV_ROUND_UP are useful macros for other
architectures. This patch moves them from soc/nvidia/tegra/types.h
to commonlib/include/commonlib/helpers.h .
Change-Id: I54521d9b197934cef8e352f9a5c4823015d85f01
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16415
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is necessary for PCI express graphics card add-ons,
otherwise the pci allocator cannot fit the mmio for the
add on card into the space it has available and the OS
turns off the card. Old value was 1GiB.
Change-Id: I606994501b15e636fe209d1ed4b3d3f73b42bf5c
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
No more hang on DMI init when wait for DMI is re-enabled.
Previously the virtual channel arbitration table was not being
set up in the south/north bridges causing invalid DMI state.
This has been tested on GA-G41M-ES2L with patches following.
An NVIDIA GT218 card was detected by the OS and displayed using
the nouveau driver with no blobs.
Change-Id: I35e03c40f5f7aa4915afd5d26db7ab053abcf0cd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16491
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The field that was previously named 'efr' is actually the iommu feature
info field. The efr field is a 64-bit field that is only present in
type 11h or type 40h headers that follows the iommu feature info field.
Change-Id: I62c158a258d43bf1912fedd63cc31b80321a27c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16508
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The revision field was correct, but the comment was wrong. The revision
1 means that the IVRS table only uses fixed length device entries.
Update the field to use the IVRS revision #define.
Change-Id: I4c030b31e3e3f0a402dac36ab69f43d99e131c22
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16507
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
According to "G45: Volume 3: Display Register
Intel ® 965G Express Chipset Family and Intel ®
G35 Express Chipset Graphics Controller" some registries
are set incorrectly in gm45/gma.c.
Some values are changed after comparing them with the values
the i915 linux kernel (3.13 was used) module sets while modesetting.
The values were obtained using 'intel_reg' from intel-gpu-tools,
during a normal boot and with 'nomodeset' as a kernel argument.
Some registers that don't exist on gm45 are set in gma.c, which is
probably the result of copying code from a more recent intel
northbridge.
The result is that that gm45 laptops with wxga displays still work as
before. gm45 laptops with wxga+ or higher resolution now just work,
where previously a black screen was shown.
TEST: build with native graphic init and flash on a gm45 target, like
lenovo x200.
Change-Id: If66b60c7189997c558270f9e474851fe7e2219f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16217
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Remove an unusued function declaration that caused problems while
compiling the target.
Change-Id: Idfd73693e9b0e1777cafa4706113fde394e95795
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16435
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
If the TPM completely fails to respond then the vendor structure may not
have assigned handlers yet, so catch that case and return error so the
boot can continue to recovery mode instead of asserting over and over.
Change-Id: If3a11567df89bc73b4d4878bf89d877974044f34
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16416
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Enable the I2C based TPM on the reef board at
bus 2 and address 0x50.
This makes vboot functional without needing MOCK_TPM and
results in the following in the SSDT:
Device (TPMI)
{
Name (_HID, "GOOG0005") // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
Name (_DDN, "I2C TPM") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
I2cSerialBus (0x0050, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer)
Interrupt (ResourceConsumer, Edge, ActiveLow, Exclusive)
{
0x00000039
}
})
}
Change-Id: Ia9775caabeac3e6a3bd72de38f9611b4cea7cea4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16398
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add code to generate an ACPI descriptor for an I2C TPM based
on the device as described in devicetree.cb.
This currently requires the devicetree to provide the HID,
since we don't currently talk to the TPM in ramstage and I
didn't want to add yet another init path for it here.
This was tested on a reef board to ensure that the device
is described properly in the SSDT.
Change-Id: I43d7f6192f48e99a4074baa4e52f0a9ee554a250
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16397
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for the cr50 TPM used in apollolake chromebooks.
This requires custom handling due to chip limitations, which
may be revisited but are needed to get things working today.
- timeouts need to be longer
- must use the older style write+wait+read read protocol
- all 4 bytes of status register must be read at once
- same limitation applies when reading burst count from status reg
- burst count max is 63 bytes, and burst count behaves
slightly differently than other I2C TPMs
- TPM expects the host to drain the full burst count (63 bytes)
from the FIFO on a read
Luckily the existing driver provides most abstraction needed to
make this work seamlessly. To maximize code re-use the support
for cr50 is added directly instead of as a separate driver and the
style is kept similar to the rest of the driver code.
This was tested with the cr50 TPM on a reef board with vboot
use of TPM for secdata storage and factory initialization.
Change-Id: I9b0bc282e41e779da8bf9184be0a11649735a101
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16396
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Allow the sleep durations used by the driver to be set by the
specific chip so they can be tuned appropriately.
Since we need to read the chip id to know the values use very
conservative defaults for the first command and then set it
to the current values by default.
Change-Id: Ic64159328b18a1471eb06fa8b52b589eec1e1ca2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16395
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use CAR accessors where needed for accessing static data.
In some cases this required some minor restructuring to pass
in a variable instead of use a global one.
For the tpm_vendor_init the structure no longer has useful
defaults, which nobody was depending on anyway. This now
requires the caller to provide a non-zero address.
Tested by enabling I2C TPM on reef and compiling successfully.
Change-Id: I8e02fbcebf5fe10c4122632eda1c48b247478289
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16394
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fix a few more instances of global variable usage in the tlcl
and marshaling code for tpm2.
For the tlcl case this buffer doesn't need to be static as it
isn't used after this function exits.
Change-Id: Ia739c81d79c6cee9046ae96061045fe4f7fb7c23
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16393
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Place config DEVICETREE after the sourced mainboard Kconfig. This
gives the mainboard the opportunity to set a unique default value.
Change-Id: Id877e1e8f555334a99b6c0ee1782d06a4a2b7a04
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/16493
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the config switch CONFIG_DEBUG_SPI_FLASH on compiler level rather
then on preprocessor level to ensure that the code is compiled even if
the switch is not selected. In addition the following two changes are
introduced:
1. Prepend the debug messages with 'SPI:' to make the output more
meaningful.
2. Change the address mask from 0xffff to 0x3ff and remove the subtraction
of the constant value 0xf020 in order to print only the register
offset within the SPI controller and avoid the visibility of any
fragments from SPI base address.
3. Switch to uint8_t and friends instead of u8 to sync up with other
code in the same file.
Change-Id: Iaf46f29a775039007a402fe862839df06a4cbfaa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16499
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The pull up for CLKRUN is required to resolve keyboard slowness
and malfunctioning observed on some reef systems. The CLKRUN
signal was probed and found to be floating when the pull up
was not enabled. Also Added pull ups for the LPC Multiplexed
command, address and data lines LAD0:3 because the LPC
Interface specification requires them.
BUG=chrome-os-partner:55586
BRANCH=none
TEST=When a key is pressed, the character is immediately visible
on the screen. Also the interrupt count for i8042 increments
immediately in /proc/interrupts.
Change-Id: I16df1a0301a3994c926a609f61291761219f9e01
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/16426
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The last vestige of the proto boards is the memory sku id
gpios. The internal pullups are still required because there's
only pulldown stuffing options available on the reef boards.
BUG=chrome-os-partner:56791
Change-Id: I04d541a897ec9aacbf2011293d18242fa32896d2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16432
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Move the current NHLT configuration implementation to the baseboard
area such that other variants can leverage it or provide their
own configuration.
BUG=chrome-os-partner:56677
Change-Id: If0d48cacdc793492e1618d0eda02a149e33f0650
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16431
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Move the current memory configuration implementation to the baseboard
area such that other variants can leverage it. The swizzle config
is exported as a global to allow duplicate swizzles to use the same
structure while still allowing different memory SKUs.
BUG=chrome-os-partner:56677
Change-Id: I57201118053051c01f0e3f164ab4bbaf650b892b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16430
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add support for Chrome OS gpio ACPI table information by
providing weak implementation from the baseboard.
BUG=chrome-os-partner:56677
Change-Id: I517764b78f47fb7b3637482ff9efc053cdd1ac69
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16422
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Since multiple boards will be living within one directory move all
the macros for defining anyting related to GPIOs to the gpio.h
header file. That way, when other boards land they can override
or use them as is.
BUG=chrome-os-partner:56677
Change-Id: I36967e57fc61ef354e0b51d1ff1396ce562fa805
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16421
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
There's no common EC header file in the code base, and I didn't
want to use a header file for single declaration. Therefore,
just move the declaration to each file that uses that symbol.
BUG=chrome-os-partner:56677
Change-Id: Ibaebb0ea6a07029aec02d5185cf05ffb8593b117
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16420
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Provide APIs for the board_id() and gpio table functionality.
Default and weak implementations are provided from the baseboard.
BUG=chrome-os-partner:56677
Change-Id: I02d8deb7f60f8c4842916a9d35f51d8af74b1da4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16419
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Commit e96543e1 (vendorcode/intel: Add UDK 2015 Bindings)
had an extra underscore at the end of one of the make lines that
we missed in the review. Remove it.
Fixes this build warning:
.../Makefile.inc:34: Extraneous text after `ifeq' directive
Change-Id: I0bc76d827207b4f641ac5ff08f540a114347533b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16411
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
A recently announced Turbot system populates two Ethernet
controllers. Enable the remaining disabled PCIe port.
Also add a clarifying comment regarding the port associated
with Function 0. Coreboot must not be allowed to disable the
function which breaks PCI compatibility.
Change-Id: I2815ba7e6d68b9898091fbc21c96eeeb49c8e05a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/16429
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
MinnowBoard Turbot systems have a GPIO-controlled LED that is
generally used to indicate the CPU is running. Commit 2ae9cce8
changed the parameter for GPIO_NC, exposing an issue with the
assumed behavior of the signal. Use a pull-down to turn on the
LED.
Change-Id: I153870904c007d89016c0d47bb3db9b824ebbcff
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/16428
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Taken from upstream Linux kernel.
Change-Id: Id8c9d48b8ca3c7592dc4d78cfd092714bbbb2abf
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/15980
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
northbridge/intel/i945.
The patch has been tested both with the arch/io.h definition of
device_t enabled and disabled in order to ensure compatibility
while the transaction takes place.
Change-Id: I041c150a7b50261e26955ad9287ef05b9a06e412
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16371
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Jeremy Compostella